1、AMSC N/A FSC 5935 MIL-DTL-28731/35C 25 May 2012 SUPERSEDING MIL-C-28731/35B 4 June 1985 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, CONTACT FORK TYPE, CRIMP REMOVABLE (5.0 AMPERES) This specification is approved for use by all Departments and Agencies of the Department of Defense. The require
2、ments for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-28731. FIGURE 1. Contact, fork type, crimp removable. INCH - POUNDS Inches .003 .016 .034 .049 .072 .076 .095 .100 .580 mm 0.08 0.41 0.86 1.24 1.83 1.93 2.41 2.54 14.73 Provided by IHSNot for Resal
3、eNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-28731/35C 2 FIGURE 1. Contact, fork type, crimp removable Continued. Inches .0000050 .0000100 .001 .005 .250 .266 .480 mm 0.000127 0.000254 0.03 0.13 6.35 6.76 12.19 Provided by IHSNot for ResaleNo reproduction or networki
4、ng permitted without license from IHS-,-,-MIL-DTL-28731/35C 3 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerance is .005 (0.13 mm). All dimensions are for parts after plating. 4. Trim area not to exceed width of contact
5、across retaining lance area “X”. 5. Contact crimp for use with (AWG) wire range No. 22 to No. 30 standard type E in accordance with MIL-DTL-16878. 6. Remove all burrs and sharp edges .001 (0.03 mm) maximum. 7. Crimp tool MIL-C-22520/17-02. 8. Contact insertion and removal tool MIL-I-81969/5-01 and M
6、IL-I-81969/4-02. 9. Contact relief hole configuration, optional. FIGURE 1. Contact, fork type, crimp removable Continued. REQUIREMENTS: Dimensions and configuration: See figure 1. Contact separating force (see configuration A). Polished steel gauge from unplated contacts: 1 ounce, minimum. Plated go
7、ld over nickel contacts (contact to contact): 2 to 10 ounces. Current rating: 5 amperes, 22 AWG wire. Contact mating area: Contacts may be supplied with either overall plating or localized finish. For localized finish contacts the contact mating area shall be in accordance with detail B and MIL-DTL-
8、28731. Part or Identifying Number (PIN): M28731/35-0001 supplied loose for hand crimping installation. M28731/35-0002 supplied on a reel for automatic crimping machine installation. Identification of contact: Contacts shall be permanently imprinted with manufacturers symbol for purpose of identifyin
9、g manufacturers product (see detail A). Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue, due to the extent of the changes. Referenced documents. In addition to MIL-DTL-28731, this document references the following:
10、MIL-DTL-16878 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-28731/35C 4 CONCLUDING MATERIAL Custodians: Preparing activity: Army CR DLA - CC Navy EC Air Force 85 (Project 5935-2012-070) DLA - CC Review activities: Army AR, AT, AV, CR4, MI N
11、avy AS, MC, OS Air Force 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
