1、 Comments, suggestions, or questions on this document should be addressed to: Attn: DLA Troop Support Standardization Team, 700 Robbins Avenue, Philadelphia, PA 19111-5096. Since contact information can change, you may want to verify the currency of the address information using Acquisition Streamli
2、ning and Standardization Information System (ASSIST) online database https:/assist.daps.dla.mil/ AMSC N/A FSC 8415 INCH-POUND MIL-DTL-32082A 16 February 2012 SUPERSEDING MIL-DTL-32082 1 May 2001 DETAILED SPECIFICATION COVERALLS, MECHANICS, COLD WEATHER This specification is approved for use by all D
3、epartment and Agencies of the Department of Defense (DoD). 1. SCOPE 1.1 Scope. This specification covers requirement for a coverall made from camouflage printed cotton/nylon twill cloth intended to be worn by mechanics in the Department of the Army as a protective garment over cold weather clothing.
4、 1.2 Classification. (see 6.2). 1.2.1 Types. The coverall types are as follows: Type I - Woodland Camouflage Print Type II - Desert Camouflage Print Type III - Universal Camouflage Print 1.2.2 Sizes. The coverall sizes are as follows: Small, Medium, Large, X Large, and XX Large. Note: The above ment
5、ioned sizes may be abbreviated as: SML, MED, Large, XLG, and XXLG. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32082A 2 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in Sections 3, 4, or 5 of this
6、 specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified req
7、uirements of documents cited in Sections 3, 4, or 5 of this specification whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unle
8、ss otherwise specified, the issues of these documents are those cited in the solicitation or contract (see 6.2). COMMERCIAL ITEM DESCRIPTIONS A-A-55634 - Zippers (Fasteners, Slide Interlocking) A-A-55126 - Fastener Tape, Hook and Loop, Synthetic A-A-50199 - Thread, Polyester Core, Cotton, or Polyest
9、er Covered DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-DTL-44031 - Cloth, Camouflage Pattern, Cotton and Nylon MIL-C-44034 - Cloth, Twill, Camouflage pattern, Cotton and Nylon for Desert Uniform MIL-W-5664 - Webbing, Textile, Elastic (Copies of these documents are available online at https:/assist.daps
10、.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these
11、documents are those cited in the solicitation or contract (see 6.2). AMERICAN ASSOCIATION OF TEXTILE CHEMIST AND COLORISTS (AATCC) AATCC Test Method 88B - Smoothness of Seams in Fabrics after Repeated Home Laundering (Copies of documents are available on line at www.aatcc.org or from the American As
12、sociation of Textile Chemists and Colorists, P.O. Box 12215, Research Triangle Park, NC 27709-2215.) AMERICAN SOCIETY FOR QUALITY (ASQ) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32082A 3 ANSI/ASQ Z1.4 - Sampling Procedures and Tables fo
13、r Inspection by Attributes (Copies are available online at http:/www.asq.org or from the American Society for Quality, 600 North Plankinton Avenue, Milwaukee, WI 53203.) ASTM INTERNATIONAL ASTM D 6193 - Standard Practice for Stitches and Seams ASTM D 5035 - Standard Test Method for Breaking Force an
14、d Elongation of Textile Fabrics (Strip Method) (Copies of documents are available online at http:/www.astm.org or from the ASTM INTERNATIONAL, PO Box C700, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.) 2.4 Order of precedence. Unless otherwise noted herein or in the contract in the event
15、 of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 First article. When specified
16、 (see 6.2), a sample shall be subjected to first article inspection in accordance with (see 4.2). 3.2 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible, provided that the material m
17、eets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.3 Description. The coverall shall be a one-piece, unlined garment with a slide fastener front fly closure with heavy duty plastic front slide fastener with double sliders, underar
18、m ventilation slide fasteners with thongs, reinforced knee, elbow and seat patches. The front shall have slanted front chest pockets with two pieces of 5-1/4 inch long by 1-inch wide loop fastener tape placed (as indicated on patterns) for placement of U.S. Army tape and nametape. The coveralls also
19、 have a piece of 2-inch by 2-inch loop tape placed on front flap (as indicated on patterns) for placement of rank, and a piece of 4-inch long by 2-inch wide loop tape on right sleeve (as indicated on patterns) for placement of U.S. Flag. The coveralls have lower front patch pockets with pass through
20、s. Hook and loop fastener tape adjustment tabs for the sleeves and leg bottoms. Additional loop tape is required at sleeve and ankles to correspond with hook on tabs when in the relaxed position. The waistband shall have elastic webbing in the center back tunnel. Other pockets include hip pockets wi
21、th hook and loop closures and a bellowed utility pocket on left sleeve with loop placed on the front of the flap and pocket (as indicated on patterns) for placement of unit patch, with a hook closure. 3.4 Material. Provided by IHSNot for ResaleNo reproduction or networking permitted without license
22、from IHS-,-,-MIL-DTL-32082A 4 3.4.1 Basic material. The basic cloth shall be a Woodland Camouflage printed cotton/nylon twill cloth conforming to Class 5 of MIL-DTL-44031 for Type I, Desert Camouflage printed cotton/nylon twill cloth conforming to Class 3C of MIL-C-44034 for Type II, and Universal C
23、amouflage printed cotton/nylon twill cloth conforming to Class 3 of MIL-DTL-44031 for Type III. Use of fabric seconds or ground shade cloth is acceptable for inside the waistband and front side pass thru reinforcement pieces only. 3.4.2 Thread. Cotton-covered polyester thread conforming to A-A-50199
24、 shall be used in the following thread sizes: Tex size 61-70 and Tex size 36-45, 3-ply for 301 stitch type; and Tex size 31-35, 2-ply for overedging. For the alternate seam type (LSbm-3), the 516 safety stitch portion of the seam shall be Tex size 36-45, 2 ply for all 401 stitching portions (top and
25、 bottom threads), and the overedge stitch portion shall be Tex size 36-45, 2 ply for the needle with Tex size 31-35, 2-ply for the loopers. For the 301 lockstitch-topstitch portion use Tex size 61-70, 2 ply, for the needle and Tex size 36-45, 2 ply for the bobbin. The color for Type I shall be Camou
26、flage Green 483, approximating color chip 34094, Type II shall be Khaki P-1, C. A. 66019 and Type III shall be Foliage Green 504. 3.4.3. Fastener tape. The hook and loop tape conforming to A-A-55126 shall be Camouflage Green 483 for Type I , Tan 380 for Type II or Foliage Green 504 for Type III. Tap
27、e maybe cut ultrasonically or with a hot knife. As an alternate, except without selvage edges, YKK Cosmolon Edge to Edge with heat-sealed edges or Velcro “DD” an edge to edge loop tape (or equal), may be used (see 6.4). 3.4.4 Elastic webbing. The elastic webbing for the waistband section shall be 1-
28、1/2 inches wide, conforming to Type II of MIL-W-5664. Colorfastness requirements shall not apply. The elastic shall be completely covered on the inside of the coverall with a tunnel of basic material. The elastic shall be caught in the stitching at both ends, but not in the stitching forming the top
29、 and bottom of the tunnel. The elastic shall be cut to the following lengths as listed in Table I: TABLE I. Elastic webbing for waistband Size Length (inches) Small 14-1/2 Medium 16-1/2 Large 18-1/2 X Large 20-1/2 XX Large 22-1/2 Tolerance + 1/2 3.4.5 Zippers (slide fastener). The zippers shall conf
30、orm to the requirements of A-A-55634 and to Table II of this document. Zipper chain shall be Type I, style 13with automatic locks, multiple mouth to mouth slider arrangement, open top, bridge bottom plastic individual element chain with minimum of (Size 10) 160 pounds or (size 9) 145 pounds crosswis
31、e strength for front closure and (Size 5) 100 pounds for pockets and underarm. The slide fastener tape shall be polyester and shall approximately match the color of the basic material. Both pronged and solid Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IH
32、S-,-,-MIL-DTL-32082A 5 bottom stops shall be acceptable. Lengths of slide fasteners in Table II shall be measured from stop to stop. TABLE II. Zippers (Slide fasteners) Location Quantity Type Style Size Length (inches) Direction of slide fastener to close Front opening 1 I 13 9 or 10 Small 27-1/2 Me
33、d 28-1/2 Large 29-1/2 X Large 30-1/2 XX Large 31-1/2 Top slider upward and bottom slider downward Slanted chest pockets 2 I 4 5 7 Downward (toward the center) Ventilation underarm 2 I 4 5 10 Downward (toward body) 3.4.6 Zipper thong. All zippers shall have a 3/8 inch wide thong tied to the pull sect
34、ion made from plain weave nylon tape with a breaking strength of 200 pounds. The length of the finished thong shall be 3 to 3-1/2 inches. The color of the thong shall be Black 357 or Camouflage Green 483 for Type I, Tan 380 for Type II or Foliage Green 504 for Type III. As an alternate the thong can
35、 be made from basic material with all sides and ends turned in or otherwise clean finished. 3.5 Labels. Each coverall shall have a size label, an identification label, and a care label. The size and identification labels or the identification and care labels may be combined. The identification label
36、 shall contain the size, NSN, item nomenclature, contract number and fiber content. The inscription shall have a minimum font size of 10 points. The inscription legibility, label, and label attachment shall last the expected life of the coveralls. The labels shall be stitched flat on all four sides
37、on the inside center back of the garment approximately 1 inch below the collar. The care or the combination label shall include the following information: 1. Coveralls may be worn over intermediate layer of the cold, dry combat uniform. 2. WARNING: Launder with zippers and hook and loop fasteners en
38、gaged. Do not use iron on hook and loop fasteners. 3. Pockets are designed to accommodate operational equipment and personal effects. 4. Launder in accordance with laundry formula E in fixed laundries or laundry formula I in field laundries. 5. DO NOT USE STARCH OR BLEACH. 6. DO NOT REMOVE THIS LABE
39、L. 3.5.1 Bar coding. Bar codes (if applicable) shall be as specified in the solicitation and/or contract (see 6.2). 3.6 Patterns. The Government shall furnish a complete set of patterns or a master pattern Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-
40、,-,-MIL-DTL-32082A 6 with grade rules to maintain uniformity and consistency in manufacturing. The Government patterns shall be used to create the contractors working patterns. Minor pattern modifications are permitted to accommodate manufacturing procedures; however the design and finished measurem
41、ents must be obtained. Pattern guidelines shall not be modified. Adhesive patterns are prohibited. Pattern parts shall be as listed in Table III. TABLE III. List of pattern parts Reference Number Pattern piece Cut parts 1 Sleeve tab 4 2 Leg tab 4 3 Sleeve pocket divider 1 4 Sleeve pocket flap 1 5 Fr
42、ont side pass thru 2 6 Sleeve pocket 1 7 Hip pocket flap 2 8 Hip pocket 2 9 Seat patch 2 10 Elbow patch 2 11 Breast patch pocket 2 12 Knee patch 2 13 Front patch pocket 2 14 Collar 2 15 Breast patch pocket slide fastener cover 2 16 Sleeve slide fastener welting 4 17 Back belt 1 18 Upper left front 1
43、 19 Upper right front 1 20 Right Sleeve 1 21 Left Sleeve 1 22 Upper back 1 23 Lower right front 1 24 Lower left front 1 25 Lower back 2 3.7 Construction. Stitches and seams are as specified in Table IV and ASTM D 6193. If not specified, seaming shall be accomplished by stitch type 301. Drill holes w
44、hen used shall be covered. The outer edges of the thigh pockets shall be caught in the side seams. All raw edges shall be overedged. All double stitching shall be 1/4 inch gauge, with the first row 1/16 to 1/8 inch from the edge. There shall be 8 to 10 stitches per inch. Gauge of stitching for the h
45、ook and loop fastener tape shall be 1/8 to 3/16 inches from the edges. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32082A 7 TABLE IV. Construction Reference Number Component Stitch Type Seam Type 1. Shoulder, armhole and underarm seam, si
46、de seam, inseam, waist seam, crotch and seat seam shall be double lapped double stitched, 1/4 inch gauge. As an alternate, join sleeves to armhole and over-edge raw edges, turn seam toward body and raise stitch 3/16 to 1/4 inch from the edge, except stitch type shall be 301 topstitched. 301 or 401 L
47、Sc-2 or LSbm-3 2. Pocket flaps, ankle and sleeve tabs, and collar: single topstitch, 1/4 inch gauge. 301 Sse-2 3. Knee, elbow, and seat patches shall be double stitched 1/4 inch gauge. 301 or 401 LSd-2 4. Sleeve hem and bottom leg hem, stitch approximately 1 inch from the edge; sleeve pocket opening
48、, stitch 5/8 inch from edge. 301 EFb-1 5. Back waist elastic tunnel. 301 SSat-2 6. The slide fastener (zipper) closures for the chest pocket and underarm ventilation shall have welting (without cording) that are flush with each other when the zipper is closed. The zipper tape shall be secured to the
49、 coverall with double stitching, 1/4 inch gauge. 301 OSf-1 7. All pockets shall be double stitched to the coverall, 1/4 inch gauge, except the utility pocket to sleeve shall be single stitched 1/16 to 1/8 inch from edge of pocket. The utility sleeve pocket shall have bellows on the sides and a pencil pocket stitched
