1、AMSC N/A FSC 5935 INCH-POUND MIL-DTL-32385/1 14 July 2011 SUPERSEDING MS90335D 5 January 1996 DETAIL SPECIFICATION SHEET CONNECTOR, RECEPTACLE, CENTER CONTACT POSITIVE, PANEL GROUND TYPE This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirem
2、ents for acquiring the product described herein shall consist of this specification sheet, MIL-DTL-32385, and QPL-32385. INTENDED USE: 1. The connectors covered by this specification sheet are intended for use on control and instrument panels for aircraft, ground, and shipboard applications. REQUIRE
3、MENTS: 1. Material: Material shall be in accordance with MIL-DTL-32385. 2. Finish: Finish shall be in accordance with MIL-DTL-32385. 3. Design: Design shall be in accordance with MIL-DTL-32385. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-
4、32385/1 2 NOTES: 1. The part or identifying number (PIN) consists of the letters MS, the specification number, and the dash number taken from table 1. MS 90335 - X Dash number (see table I) Specification number MS prefix (Retaining MS part number) TABLE I. Dash number PIN cross-reference data. Dash
5、number 1MS90335D PIN MIL-DTL-32385/2 PIN -1 MS90335-1 MS90335-1 -2 MS90335-2 MS90335-2 1See figure 1. 2. Interpret figure in accordance with ASME Y14.5. 3. When mated with MIL-DTL-32385/5, or /6 plug that has been inserted to a depth of 0.140 0.005 inch, the connector shall have a minimum withdrawal
6、 force of 3 pounds of force (lbf) and a maximum withdrawal force of 10 lbf. 4. The manufacturers identification mark shall be permanently stamped in the metal part of the connectors. 5. The current loading of the connectors is limited to the current-carrying capacity of the wire used in the associat
7、ed interconnecting cabling. 6. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. 7. Unless otherwise specified, issues of reference documents are those in effect at the time of solicitation. 8. Interchangeability
8、 relationship: MS90335-1 and MIL-DTL-32385/1-1 parts are universally, functionally and dimensionally interchangeable. MS90335-2 and MIL-DTL-32385/1-2 parts are universally, functionally and dimensionally interchangeable. Provided by IHSNot for ResaleNo reproduction or networking permitted without li
9、cense from IHS-,-,-MIL-DTL-32385/1 3 FIGURE 1. Connector, receptacle, center contact positive, panel ground type. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32385/1 4 NOTES: 1. All dimensions are in inches. 2. Tolerances: Dimensions 0.00
10、5 unless otherwise specified. 3. Female center contact fingers closed down uniformly to meet 4 ounces minimum withdrawal force with 0.079 diameter pin before and after 3 insertions of a 0.082 diameter pin. 4. Captivation of insulator and center contact will maintain 12 lbf when applied from interfac
11、e end. 5. Insulator shall not exceed diameter of body. 6. Angular dimension of 2.5 degrees. FIGURE 1. Connector, receptacle, center contact positive, panel ground type - Continued. Custodians: Preparing Activity: Army - AV Navy - AS Air Force - 85 DLA - GS DLA - GS2 (Project 5935-2011-031) Review Ac
12、tivities: Navy - MC, SH NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST database at https:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
