1、MIL-DTL-39024/13D 7 February 2011 SUPERSEDING MIL-DTL-39024/13C 22 September 2008 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, TEST POINT TYPE, PRINTED WIRING TYPE; SINGLE TEST POINT (RIGHT ANGLE, 2-LEG MOUNTING), LOW VOLTAGE, .080 This specification is approved for use by all Departments and
2、Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-39024. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. See table I for dimensions not specified on fig
3、ure 1. 4. Unless otherwise specified, tolerances are .010 (0.25 mm), and are based on 1 inch = 25.4 mm. 5. All undimensioned pictorial configurations are for reference purposes only. FIGURE 1. Configuration and dimensions. AMSC N/A FSC 5935 Inches mm .001 0.03 .050 1.27 .080 2.03 .118 3.00 .235 5.97
4、 .485 12.32 .5 12.7 INCH-POUND HOLE TO RECEIVE .080 .001 DIA PROBE X .450 LONG Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-39024/13D 2 TABLE I. Design and identification data. Dash number Dimensions (inches) 1/ Insulation A .010 (0.25) B
5、.015 (0.38) C .015 (0.38) Color Number in accordance with FED-STD-595/ -01 -02 -03 -04 -05 -06 -07 -08 -09 -10 -11 .300 (7.62) “ “ “ “ “ “ “ “ “ “ 0.060 (1.52) “ “ “ “ “ “ “ “ “ “ 0.218 (5.54) “ “ “ “ “ “ “ “ “ “ White Red Black Brown Green Orange Blue Yellow Gray Purple Natural 17875 11105 17038 10
6、075 14110 12246 15123 13655 16187 27144 - -12 -13 -14 -15 -16 -17 -18 -19 -20 -21 -22 .400 (10.16) “ “ “ “ “ “ “ “ “ “ .025 (0.64) “ “ “ “ “ “ “ “ “ “ .175 (4.45) “ “ “ “ “ “ “ “ “ “ White Red Black Brown Green Orange Blue Yellow Gray Purple Natural 17875 11105 17038 10075 14110 12246 15123 13655 16
7、187 27144 - 1/ Dimensions are in inches. Metric equivalents are given for information only. REQUIREMENTS: Design and construction: Dimensions and configuration: See figure 1 and table I. Insulation: Material shall be polyamide in accordance with L-P-410 or ASTM D4066. Flammability: Dielectric materi
8、als shall be self-extinguishing in accordance with ASTM D635. Test probe: 0.080 0.001-inch diameter and .450 inch (min) length. Test probe shall be engaged a minimum of .450 inches. Test probe shall be fully inserted. Contact current rating: 5 amperes (maximum). Contact sleeve: Shall be formed of st
9、rip to make a cylinder with a butted seam. Contact resistance: A test probe in accordance with MIL-DTL-39024 shall be fully inserted in the connector. With a current of 5 amperes, potential drop shall be measured between the connector terminal and the extreme end of the solder cup on the test probe.
10、 Measured values shall be within the limits specified in table II. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-39024/13D 3 TABLE II. Potential drop (max) with 5 amperes of current. Test Before test After test Durability Vibration Salt spr
11、ay (corrosion) 6 mV 8 mV 10 mV 8 mV 10 mV 15 mV Dielectric withstanding voltage (at sea level): Test voltage: 3,800 volts rms, 60 hertz, shall be applied for a period of 15 seconds. Insertion and withdrawal forces: Insertion force: 5.0 pounds (max). Withdrawal force: 0.4 pound (min). Identification
12、marking: Part or Identifying Number (PIN): M39024/13-(dash number from table I). Operating conditions: Operating voltage: 2,400 volts rms, 60 hertz at sea level; 350 volts rms, 60 hertz at 80,000 feet. Qualification: Not applicable. Conformance inspection. Groups A and B tests in accordance with MIL
13、-DTL-39024 shall be applicable. Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in th
14、ese notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced documents. In addition to MIL-DTL-39024, this document references the followin
15、g: ASTM D4066 FED-STD-595/15123 ASTM D635 FED-STD-595/16187 FED-STD-595/10075 FED-STD-595/17038 FED-STD-595/11105 FED-STD-595/17875 FED-STD-595/12246 FED-STD-595/27144 FED-STD-595/13655 L-P-410 FED-STD-595/14110 Provided by IHSNot for ResaleNo reproduction or networking permitted without license fro
16、m IHS-,-,-MIL-DTL-39024/13D 4 CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force 85 DLA - CC (Project 5935-2010-196) Review activities: Army - AR, CR4, MI Navy - AS, CG, MC, OS Air Force 19 NOTE: The activities listed above were interested in this document as of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
