1、INCH-POUND MIL-DTL-39024/14C 22 September 2008 SUPERSEDING MIL-DTL-39024/14B 3 February 2003 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, TEST POINT TYPE, PANEL TYPE; SINGLE TEST POINT SUBMINIATURE (PUSH-IN), LOW VOLTAGE, .080 This specification is approved for use by all Departments and Agenc
2、ies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-39024. Inches mm Inches mm .001 0.03 .085 2.16 .005 0.13 .100 2.54 .015 0.38 .187 4.75 .02 0.5 .190 4.83 .045 1.14 .218 5.54 .060 1.52 .281 7.14 .080 2.
3、03 .500 12.70 .685 17.40 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only, and are based on 1 inch = 25.4 mm. 3. Unless otherwise specified, tolerances are .010 (0.25 mm). 4. Recommended mounting hole diameter .218 .001 (5.54 0.03 mm). 5. Range of acceptable p
4、anel thickness: .031 - .093 (0.79 2.36 mm). 6. Parts supplied unassembled. 7. All undimensioned pictorial configurations are for reference purpose only. 8. When unassembled, this dimension shall be .218 .005 (5.54 0.13 mm). When the terminal assembly and insulator are assembled, this dimension shall
5、 be .220 (5.59 mm) minimum. FIGURE 1. Configuration and dimensions. AMSC N/A FSC 5935Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-39024/14C 2 TABLE I. Design and identification data. Insulation Dash number Material Color Number in accordan
6、ce with FED-STD-595/ -01 -02 -03 -04 -05 -06 -07 -08 -09 -10 -11 L-P-410 or ASTM D4066 White Red Black Brown Green Orange Blue Yellow Gray Purple Natural 17875 11105 17038 10075 14110 12246 15123 13655 16187 27144 - -12 -13 -14 -15 -16 -17 -18 -19 -20 -21 -22 ASTM D1710 White Red Black Brown Green O
7、range Blue Yellow Gray Purple Natural 17875 11105 17038 10075 14110 12246 15123 13655 16187 27144 - REQUIREMENTS: Design and construction: Dimensions and configuration: See figure 1. Insulation: Material shall be as specified in table I. Socket contact and terminals: Material shall be as specified i
8、n MIL-DTL-39024. Flammability: Dielectric materials shall be self-extinguishing in accordance with ASTM D635. Terminals: Shall be capable of being wired with two no. 20 AWG wires. Configuration shall be specified on figure 1. Test probe: 0.080 0.001 inch in diameter and -inch (min) length. Test prob
9、e shall be engaged for a minimum of inch. Contact current rating: 5 amperes (max). Contact resistance: A test probe in accordance with MIL-DTL-39024 shall be fully inserted in the connector. With a current of 5 amperes, potential drop shall be measured between the connector terminal and the extreme
10、end of the solder cup on the test probe. Measured values shall be within the limits specified in table II. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-39024/14C 3 TABLE II. Potential drop (max) with 5 amperes of current. Test Before test
11、After test Durability 6 mV 8 mV Vibration 8 mV 10 mV Salt spray (corrosion) 10 mV 15 mV Dielectric withstanding voltage (at sea level): Test voltage: 3,000 volts rms, 60 hertz, shall be applied to the insulting material for period of 15 seconds. Insertion and withdrawal forces: Insertion force: 5.0
12、pounds (max). Withdrawal force: 0.4 pound (min). Identification marking: Part or Identifying Number (PIN): M39024/14-(dash number from table I). Operating conditions: Operating voltage: 2,000 volts rms, 60 hertz at sea level; 350 volts rms, 60 hertz at 80,000 feet. The thickness of the panel on whic
13、h these connectors may be used ranges from 0.031 to 0.093 inch; the diameter of the mounting hole is 0.218 0.001 inch. Qualification: Not applicable. Conformance inspection. Groups A and B tests in accordance with MIL-DTL-39024 shall be applicable. Changes from previous issue. The margins of this sp
14、ecification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements o
15、f this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced documents. In addition to MIL-DTL-39024, this document references the following: ASTM D635 FED-STD-595/14110 ASTM D1710 FED-STD-595/15123 ASTM D4066 FED-STD-595/
16、16187 FED-STD-595/10075 FED-STD-595/17038 FED-STD-595/11105 FED-STD-595/17875 FED-STD-595/12246 FED-STD-595/27144 FED-STD-595/13655 L-P-410 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-39024/14C 4 CONCLUDING MATERIAL Custodians: Preparing
17、activity: Army - CR DLA - CC Navy - EC Air Force - 85 (Project 5935-2008-047) DLA - CC Review activities: Army - AR, CR4, MI Navy - AS, CG, MC, OS Air Force 19 NOTE: The activities listed above were interested in this document as of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
