1、MIL-DTL-39024/15C INCH-POUND 22 September 2008 SUPERSEDING MIL-DTL-39024/15B 3 February 2003 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, TEST POINT TYPE, PRINTED WIRING TYPE; SINGLE TEST POINT, LOW VOLTAGE, .080 This specification is approved for use by all Departments and Agencies of the Dep
2、artment of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-39024. Inches mm Inches mm .001 0.03 .136 3.45 .002 0.05 .187 4.75 .015 0.38 .235 5.97 .018 0.46 .310 7.87 .020 0.51 .500 12.70 .080 2.03 .510 12.95 .132 3.35 .530 13
3、.46 .134 3.40 .550 13.97 NOTES: 1. Dimensions are in inches. (See table for dimensions not specified on figure 1). 2. Metric equivalents are given for information only and are based on 1 inch = 25.4 mm. 3. Unless otherwise specified, tolerances are .010 (0.25 mm). 4. All dimensionless pictorial conf
4、igurations are for reference purposes only. FIGURE 1. Configuration and dimensions. AMSC N/A FSC 5935 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-39024/15C 2 TABLE I. Design and identification data. Dimension Insulation Dash Terminal numb
5、er style 1A (inches /) Material Color Number in accordance with FED-STD-595/ -01 -02 -03 -04 -05 -06 -07 -08 -09 -10 -11 Type “A” long .327 (8.31) .297 (7.54) White Red Black Brown Green Orange Blue Yellow Gray Purple Natural 17875 11105 17038 10075 14110 12246 15123 13655 16187 27144 - -12 -13 -14
6、-15 -16 -17 -18 -19 -20 -21 -22 Type “B” med short .180 (4.57) .160 (4.06) White Red Black Brown Green Orange Blue Yellow Gray Purple Natural 17875 11105 17038 10075 14110 12246 15123 13655 16187 27144 - -23 -24 -25 -26 -27 -28 -29 -30 -31 -32 -33 Type “B” short .120 (3.05) .100 (2.54) L-P-410, ASTM
7、 D4066 White Red Black Brown Green Orange Blue Yellow Gray Purple Natural 17875 11105 17038 10075 14110 12246 15123 13655 16187 27144 - -34 -35 -36 -37 -38 -39 -40 -41 -42 -43 -44 Type “A” long .327 (8.31) .297 (7.54) ASTM D1710 White Red Black Brown Green Orange Blue Yellow Gray Purple Natural 1787
8、5 11105 17038 10075 14110 12246 15123 13655 16187 27144 - See notes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-39024/15C 3 TABLE I. Design and identification data. Continued. Dimension Insulation Dash Terminal number sty
9、le A (inches 1/) Material Color Number in accordance with FED-STD-595/ -45 -46 -47 -48 -49 -50 -51 -52 -53 -54 -55 Type “B” med short .180 (4.57) .160 (4.06) White Red Black Brown Green Orange Blue Yellow Gray Purple Natural 17875 11105 17038 10075 14110 12246 15123 13655 16187 27144 - -56 -57 -58 -
10、59 -60 -61 -62 -63 -64 -65 -66 Type “B” short .120 (3.05) .100 (2.54) ASTM D1710 White Red Black Brown Green Orange Blue Yellow Gray Purple Natural 17875 11105 17038 10075 14110 12246 15123 13655 16187 27144 - 1/ Dimensions are in inches. Metric equivalents are given for information only. REQUIREMEN
11、TS: Design and construction: Dimensions and configuration: See figure 1 and table I. Insulation: Material as specified in table I. Flammability: Dielectric materials shall be self-extinguishing in accordance with ASTM D635. Test probe: 0.080 0.001 inch in diameter and -inch (min) length. Test probe
12、shall be engaged a minimum of inch. Contact current rating: 5 amperes (max). Contact resistance: A test probe in accordance with MIL-DTL-39024 shall be fully inserted in the connector. With a current of 5 amperes, potential drop shall be measured between the connector terminal and the extreme end of
13、 the solder cup on the test probe. Measured values shall be within the limits specified in table II. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-39024/15C 4 TABLE II. Potential drop (max) with 5 amperes of current. Test Before test After
14、test Durability 6 mV 8 mV Vibration 8 mV 10 mV Salt spray (corrosion) 10 mV 15 mV Dielectric withstanding voltage (at sea level): Test voltage: 1,800 volts rms, 60 hertz, shall be applied for period of 15 seconds. Insertion and withdrawal forces: Insertion force: 5.0 pounds (max). Withdrawal force:
15、0.4 pound (min). Identification marking: Part or Identifying Number (PIN): M39024/15-(dash number from table I). Operating conditions: Operating voltage is as follows: 1,200 volts rms, 60 hertz at sea level; 300 volts rms, 60 hertz at 80,000 feet. Qualification: Not applicable. Conformance inspectio
16、n. Groups A and B tests in accordance with MIL-DTL-39024 shall be applicable. Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no l
17、iability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced documents. In addition to MIL-DT
18、L-39024, this document references the following: ASTM D635 FED-STD-595/14110 ASTM D1710 FED-STD-595/15123 ASTM D4066 FED-STD-595/16187 FED-STD-595/10075 FED-STD-595/17038 FED-STD-595/11105 FED-STD-595/17875 FED-STD-595/12246 FED-STD-595/27144 FED-STD-595/13655 L-P-410 Provided by IHSNot for ResaleNo
19、 reproduction or networking permitted without license from IHS-,-,-MIL-DTL-39024/15C 5 CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 85 (Project 5935-2008-048) DLA - CC Review activity: Army MI NOTE: The activities listed above were interested in this document as of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
