1、MIL-DTL-39024/18F 22 September 2008 SUPERSEDING MIL-DTL-39024/18E 3 February 2003 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, TEST POINT TYPE, PRINTED WIRING TYPE; MICRO-MINIATURE, SINGLE TEST POINT (2-LEG MOUNTING), LOW VOLTAGE, .080 INCH This specification is approved for use by all Departm
2、ents and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-39024. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Mounting to fit .052 (1.32 mm) dia hol
3、es (2 holes), and lead spacing shall be such to meet .200 .005 mounting hole layout requirements. 4. Dimensions are valid after plating only. FIGURE 1. Dimensions and configuration. AMSC N/A FSC 5935 Inches mm Inches mm .001 .002 .005 .008 .010 .015 .020 0.03 0.05 0.13 0.20 0.25 0.38 0.51 INCH-POUND
4、 .040 1.02 .052 1.32 .115 2.92 .125 3.18 .187 4.75 .200 5.08 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-39024/18F 2 TABLE I. Dash number and identification data. Dash number Insulation color in accordance with MIL-STD-104 01 02 03 04 05
5、06 07 08 09 10 White Yellow Brown Red Orange Black Green Blue Gray Purple REQUIREMENTS: Design and construction: Dimensions and configuration: See figure 1. Contact: Contact shall be phosphor bronze in accordance with ASTM B139/B139M. Insulation: Material shall be polytetrafluoroethylene in accordan
6、ce with MIL-I-22129 or equal. Test probe: 0.080 0.001 inch in diameter (connector shall accept test probe from either end). Operating voltage: 1,000 volts rms, maximum. Operating temperature range: -65C to +200C. Insulation resistance: Test circuit in MIL-DTL-39024 shall be used. Dielectric withstan
7、ding voltage: Test circuit in MIL-DTL-39024 shall be used. Test voltage (sea level): 1,000 volts rms, 60 hertz, shall be applied for 15 seconds. Test voltage (50,000 feet): 350 volts rms, 60 hertz, shall be applied for 15 seconds. Insertion and withdrawal forces: Insertion force: 10.0 pounds (max).
8、Withdrawal force: 0.5 pound (min). Resistance to test probe damage: inch-pound moment shall be used for insertion depth of 3/16 inch and inch. Shock (specified pulse): Method 213, test condition I of MIL-STD-202. Provided by IHSNot for ResaleNo reproduction or networking permitted without license fr
9、om IHS-,-,-MIL-DTL-39024/18F 3 Vibration, high frequency: 15 gs at 10 to 2,000 Hz, method 204, test condition B of MIL-STD-202. Durability: 150 insertion/withdrawal cycles. Identification marking: Part or Identifying Number (PIN): M39024/18-(dash number from table I). Operating conditions: These con
10、nectors are designed for 1/16 inch nominal thickness printed wiring board (PIN M39024/18-01 thru 10) Supersession data: This specification includes the requirements of contractor (90348) specification 2134873; contractor (05869) specification 716007. Qualification: Not applicable. Conformance inspec
11、tion. Groups A and B tests in accordance with MIL-DTL-39024 shall be applicable. Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes n
12、o liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced documents. In addition to MIL
13、DTL-39024, this document references the following: ASTM B139/B139M MIL-I-22129 MIL-STD-104 MIL-STD-202 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-39024/18F 4 CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA - CC Navy -
14、EC Air Force - 85 (Project 5935-2008-045) DLA - CC Review activities: Army - AR, CR4, MI Navy - AS, CG, MC Air Force 19 NOTE: The activities listed above were interested in this document as of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
