1、AMSC N/A FSC 7110 INCH-POUND MIL-DTL-43101B 11 January 2013 SUPERSEDING MIL-F-43101A 29 May 1967 DETAIL SPECIFICATION FILING CABINET, LETTER SIZE DESIGN, STEEL, OD, ONE DRAWER HIGH, ONE DRAWER WIDE This specification is approved for use by all Departments and Agencies of the Department of Defense. 1
2、. SCOPE 1.1 This specification covers one type and size filing cabinet. 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3, 4, or 5 of this standard. This section does not include documents cited in other sections of this standard or recommend for a
3、dditional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3, 4, or 5 of this standard, whether or not they are listed. 2.2 Government docum
4、ents. 2.2.1 Specifications, standards, and handbooks. The following specifications and standards form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. FEDERAL SPECIFICATIONS QQ-S-698 Ste
5、el, Sheet and Strip, Low Carbon TT-C-490 Chemical Conversion Coatings and Pretreatments for Ferrous Surfaces (Base for Organic Coatings) FEDERAL STANDARDS FED-STD-595/24084 Green, Semigloss DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-DTL-53030 Primer Coating, Epoxy, Water Based, Lead and Chromate Free
6、Comments, suggestions, or questions on this document should be addressed to Defense Supply Center Philadelphia (DSCP), ATTN: DSCP-NASA, 700 Robbins Avenue, Philadelphia, PA 19111-5096 or e-mail to dscpg&ispecommentsdla.mil . Since contact information can change, you may want to verify the currency o
7、f this address information using the ASSIST Online database at https:/assist.dla.mil . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-43101B 2 DEPARTMENT OF DEFENSE STANDARDS MIL-STD-130 Identification Marking of U.S. Military Property (Copi
8、es of these documents are available online at https:/assist.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2.2 Other Government documents, drawings, and publications. The following other Government documents, dra
9、wings, and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DRAWINGS U.S. ARMY NATICK SOLDIER RESEARCH DEVELOPMENT AND ENGINEERING CENTER 5-13-211 Filing Cabinet, Lette
10、r Size Design, Steel, OD, One DrawerHigh, One Drawer Wide, Instruction Sheet 5-13-2115 Filing Cabinet, Letter Size Design, Steel, OD, One Drawer High, One Drawer Wide, Assembly Complete 5-13-2116 Filing Cabinet, Letter Size Design, Steel, OD, One Drawer High, One Drawer Wide, Drawer Assembly 5-13-21
11、17 Filing Cabinet, Letter Size Design, Steel, OD, One Drawer High, One Drawer Wide, Back Assembly, Drawer 5-13-2118 Filing Cabinet, Letter Size Design, Steel, OD, One Drawer High, One Drawer Wide, Body Assembly 5-13-2119 Filing Cabinet, Letter Size Design, Steel, OD, One Drawer High, One Drawer Wide
12、, Follower Assembly 5-13-2124 Filing Cabinet, Letter Size Design, Steel, OD, One Drawer High, One Drawer Wide, Body Details (Miniature copy of Drawings 5-13-211 and 5-13-2115 identified as figures 1 and 2 are attached for information purposes only.) (Copies of these documents are available from Nati
13、ck Soldier Research Development and Engineering Center, Kansas Street Bldg. 3, Natick, MA 01760.) 2.3 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the sol
14、icitation or contract. AMERICAN SOCIETY FOR QUALITY (ASQ) ASQ Z1.4 Sampling Procedures and Tables for Inspection by Attributes. (Copies of this document are available from www.asq.org or the American Society for Quality, 600 North Plankinton Avenue, Milwaukee, WI 53203.) Provided by IHSNot for Resal
15、eNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-43101B 3 AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) ASTM A108 Plate, Brass, Sheet Strip, and Rolled Bar ASTM D4066 Nylon Injection and Extrusion Materials (PA) ASTM E1282 Density and Specific Gravity (Relative Densi
16、ty) of Plastics by Displacement (Copies of these documents are available from www.astm.org or the American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.) MASTER PAINTERS INSTITUTE (MPI) MPI #94 Alkyd, Exterior, Semi-Gloss (MPI Gloss Level 5) (Copies of t
17、his document are available from or the Master Painters Institute Inc., 2800 Engleton Avenue, Burnaby, BC CANADA V5C 6G7.) NATIONAL AEROSPACE STANDARDS (NAS) NASM35793 Handle, Bail-Chest, Surface Mounting, Plain Holes (Copies of this document are available from www.aia-aerospace.org or the Aerospace
18、 Industries Association of America 1250 Eye Street,N.W., Suite 1200 Washington, DC, United States, 20005-3924.) 2.4 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this do
19、cument takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 First article. When specified (see 6.2), samples shall be subjected to first article inspection in accordance with 4.2. 3.2 Materi
20、als. Materials not definitely specified shall conform to the quality normally used for the purpose in standard industry practice. 3.2.1 Steel. 3.2.1.1 Low carbon, cold rolled, sheet and strip. Low carbon cold rolled steel sheet and strip shall conform to 10091020, commercial quality (CRCQ), or tempe
21、r No. 3 respectively of QQ-S-698. 3.2.1.2 Low carbon, hot rolled, sheet and strip. Low carbon hot rolled steel sheet and strip shall conform to commercial quality (HRCQ), pickled and oiled finish (PO), 1009-1020 of QQ-S-698. 3.2.1.3 Spring, flat, carbon, cold rolled sheet, general purpose. General p
22、urpose carbon spring steel shall conform to 70 80 percent carbon commercial grade flat spring quality. 3.2.1.4 Carbon, cold finished, bar. Cold finished carbon bar shall be 1010 or 1015, condition ACD, annealed and cold drawn, any applicable form of ASTM A108. 3.2.2 Plastic molding (nylon). Nylon sh
23、all conform to any color, Group PA01, Class 1, Grades 1 thru 4 or Group PA02, Class 1, Grades 1 thru 4 of ASTM D4066. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-43101B 4 3.2.3 Primer. Enamel shall conform to Type II of MIL-DTL-53030. 3.2
24、.4 Enamel. Enamel shall conform to Master Painters Institute, Reference #94, Exterior Alkyd, Semi-Gloss, MPI Gloss Level 5. The color shall be green, FED-STD-595/24084. 3.3 Construction. The construction of the filing cabinet shall conform to the design and details shown on Drawings 5-13-2115 throug
25、h 5-13-2119, 5-13-2124 and as specified herein (see figure 2). 3.3.1 Body. The cabinet body shell, closed and open end supports, channels, reinforcements and rear body plates, shall be fabricated from steel specified in 3.2.1.1. The holder, lock lever, bar, slip key and bracket and lock bar shall be
26、 fabricated of steel specified in 3.2.1.2. 3.3.2 Drawer. The drawer assembly and the follower assembly, except for the spring and handle shall be fabricated from steel specified in 3.2.1.1. The drawer shall mount into the body and the drawer suspension system shall operate smoothly without binding.
27、The follower assembly shall adjust to the full depth of the drawer and shall be removable without special tools. 3.3.2.1 Spring. The spring on the follower assembly shall be fabricated from steel specified in 3.2.1.3. 3.3.2.2 Handle. The handles with mounting plate, on the complete drawer assembly s
28、hall conform to NASM35793, part number MS35793-1 except that the material for the mounting plate shall be as specified in 3.2.1.1 and the material for the handle shall conform to 3.2.1.4. 3.3.2.3 Glides. The glides on the bottom front of the body shall be fabricated of nylon specified in 3.2.2. 3.3.
29、3 Welding. Surfaces to be welded shall be cleaned and free of rust, scale, corrosion, oil and other foreign matter. 3.3.4 Riveting. Holes for rivets containing burrs that would prevent seating of rivets shall be removed. Rivets, when driven shall have heads in full contact with the surface of the co
30、ntacting metal. Rivets shall be securely peened or clinched. Rivet heads shall not be cracked or split. 3.4 Finish. 3.4.1 Surface pretreatment. After fabrication, all surfaces of the filing cabinet shall be pretreated in accordance with Type I or II of TT-C-490. 3.4.2 Priming and enameling. Surfaces
31、, pretreated as specified in 3.4.1, shall be coated with primer specified in 3.2.3. The primed surfaces shall then be coated with enamel specified in 3.2.4. Primer may be omitted from any surface prepared for painting in accordance with 3.4.1, provided not less than two coats of enamel are applied.
32、3.5 Instruction sheet. Each filing cabinet shall be furnished with an 8 by 10.5 inch instruction sheet in accordance with drawing 5-13-211 (see figure 1). The instruction sheet shall be placed inside the filing cabinet between the front panel and the follower. 3.6 Marking. The filing cabinet shall b
33、e marked in accordance with MIL-STD-130. 3.7 Workmanship. All surfaces shall be free of burrs, slivers, rough or sharp edges. Components shall not be broken, cracked, split or malformed. Welds shall be sound and free from porosity, cracks or incomplete fusion. All welds shall be smooth and free from
34、 pits, flashes and burn through. Enamel shall level out to a uniform dry film thickness without runs, drops or areas of no film. The coating shall be free from imbedded foreign matter and shall show no evidence of peeling, flaking or blistering. Provided by IHSNot for ResaleNo reproduction or networ
35、king permitted without license from IHS-,-,-MIL-DTL-43101B 5 4. VERIFICATION 4.1 Classification of inspection. The inspection of filing cabinets shall be classified as follows: (a) First article inspection (see 4.2) (b) Conformance inspection (see 4.3) 4.2 First article inspection. When a first arti
36、cle sample is required, it shall be examined for defects in Table II and dimensions specified. 4.3 Conformance inspection. Conformance inspection shall include paragraphs 4.3.1 through 4.3.4. Sampling for inspection shall be performed in accordance with the provisions set forth in ASQ Z1.4, except w
37、here otherwise indicated. 4.3.1 Component and material inspection. Components and materials shall be inspected and tested in accordance with all the requirements of referenced specifications, drawings, and standards unless otherwise excluded, amended, modified or qualified in this specification or a
38、pplicable purchase document. 4.3.1.1 Spring steel carbon content analysis. Spring steel shall be analyzed for carbon content using either chemical analysis in accordance with ASTM E1282 or an applicable spectrochemical analysis test method. Two samples shall be taken from each lot of material unless
39、 the lot consists of only one piece, in which case, one sample shall be taken. Failure of any sample to comply shall be cause for rejection of the lot. 4.3.2 In process examinations. Examination shall be made during the manufacturing process for requirements specified in Table I. Whenever nonconform
40、ance is noted, correction shall be made to affected items and process. TABLE I. In process examination. Requirement Requirement Paragraph Surfaces cleaned prior to welding Rivet hole burrs removed prior to riveting Surface pretreatment Priming when applicable 3.3.3 3.3.4 3.4.1 3.4.2 4.3.3 End item i
41、nspection. The lot shall consist of all completely fabricated filing cabinets offered for inspection at one time. The sample unit shall be one completely fabricated filing cabinet. 4.3.3.1 Visual examination. Examination shall be made of the end item for defects in Table II. The inspection level sha
42、ll be level II. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-43101B 6 TABLE II. Classification of defects. Examine Defect Classification Major Minor Finish Construction and workmanship Body and drawer assemblies Back Assembly Follower Asse
43、mbly Welding Not as specified Not color specified Area of no film Not continuous or is not smooth Contains runs, drops or streaks Foreign matter imbedded Evidence of peeling, flaking or blistering Any component missing Any component not attached as specified Drawer will not mount without binding Dra
44、wer suspension system does not operate smoothly Latching mechanism does not function More than one rivet missing on handle mounting plate One rivet missing on handle mounting plate Cord holder or handle plate not attached flush Lever lock missing Rear upright assembly rollers bind or do not rotate f
45、reely Component missing or not attached as specified Component missing or not attached as specified Does not adjust the full depth of drawer Cannot be removed without special tools More than one spot weld missing, broken or not fused where specified X X X X X X X X X X X X X X X X X X X X X X 4.3.3.
46、2 Dimensional examinations. Examinations shall be made of the filing cabinet for compliance with dimensions specified. Any deviation therefrom shall constitute a defect. The inspection level shall be S-2. 4.3.4 Examination of preparation for delivery requirements. An examination shall be made to det
47、ermine that packaging, packing and marking requirements of section 5 of this specification are complied with. Defects shall be scored in accordance with Table III. The sample unit shall be one shipping container fully prepared for delivery with the exception that it need not be sealed. The lot shall
48、 be the number of shipping containers offered for delivery at one time. The inspection level shall be S-2. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-43101B 7 TABLE III. Examine of preparation for delivery. 5. PACKAGING 5.1 Packaging. Fo
49、r acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in- house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities
