1、AMSC N/A FSC 5920 MIL-DTL-5372/1B 13 May 2009 SUPERSEDING MIL-DTL-5372/1A 13 February 2004 DETAIL SPECIFICATION SHEET FUSE, LIMITER TYPE ENCLOSED LINK, 1 60 AMPERE This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the
2、product described herein shall consist of this specification sheet and MIL-F-5372. FIGURE 1. Outline drawing of fuse. INCH-POUND INACTIVE FOR NEW DESIGN AFTER 17 September 2003. NO LONGER USED EXCEPT FOR REPLACEMENT PURPOSES. Provided by IHSNot for ResaleNo reproduction or networking permitted witho
3、ut license from IHS-,-,-MIL-DTL-5372/1B 2 Ltr Inches mm Min Max Min Max A .56 .66 14.2 16.8 B .70 .80 17.8 20.3 C 1.32 1.42 33.5 36.1 D .11 .21 2.79 5.3 E .01 .11 0.3 2.8 F .03 Nominal 0.8 Nominal G .89 .99 22.6 25.1 H .09 .19 2.3 4.8 J .120 .130 3.05 3.3 K .71 .73 18.0 18.5 L .45 .55 11.4 14.0 M 1.
4、25 1.35 31.8 34.3 N 2.06 2.16 52.3 54.9 P .04 .14 1.0 3.6 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. FIGURE 1. Outline drawing of fuse - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,
5、-MIL-DTL-5372/1B 3 REQUIREMENTS: TABLE I. Ampere rating. Dash number M5372/1- Current rating amperes 01 1 02 2 03 3 05 5 10 10 15 15 20 20 25 25 30 30 35 35 40 40 50 50 60 60 Dimensions, marking, and configuration: See figure 1. Voltage rating. 115/200 volts ac, 400 Hz, 28 volts dc. Weight. 0.065 po
6、unds maximum. Materials. Body: Glass filled melamine in accordance with ASTM-D5948 type MMI-5 (white). Blades: Copper in accordance with ASTM-B152/B152M, type ETA with silver plate. Terminal strength. With body of the fuse firmly clamped, the forces below shall be applied to both terminals. TABLE II
7、. Terminal strength. Direction of force Rating To 30 amperes Above 30 amperes Force in pounds (minimum) To edge of blade 10 25 To flat side of blade 5 10 To end of blade (into fuse) 30 40 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-FIGURE 2. Fusi
8、ng current vs element melt time. (1 to 15 ampere) 4 MIL-DTL-5372/1B Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-FIGURE 3. Fusing current vs element melt time. (20 to 60 ampere) 5MIL-DTL-5372/1B Provided by IHSNot for ResaleNo reproduction or netw
9、orking permitted without license from IHS-,-,-MIL-DTL-5372/1B 6 TABLE III. Cross-reference. Superseding number Superseded numbers for CAGE 09922 27012 81755 M5372/1-01 F1L01T5 27010 4-021-1 M5372/1-02 F1L02T5 27020 4-021-2 M5372/1-03 F1L03T5 27030 4-021-3 M5372/1-05 F1L05T5 27050 4-021-5 M5372/1-10
10、F1L10T5 27100 4-021-10 M5372/1-15 F1L15T5 27150 4-021-15 M5372/1-20 F1L20T5 27200 4-021-20 M5372/1-25 F1L25T5 27250 4-021-25 M5372/1-30 F1L30T5 27300 4-021-30 M5372/1-35 F1L35T5 27350 4-021-35 M5372/1-40 F1L40T5 27400 4-021-40 M5372/1-50 F1L50T5 27500 4-021-50 M5372/1-60 F1L60T5 27600 4-021-60 Refer
11、enced documents. In addition to MIL-F-5372, this document references the following: ASTM-D5948 ASTM-B152/B152M The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes
12、no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Custodians: Preparing activity: Air For
13、ce - 85 DLA - CC DLA - CC (Project 5920-2009-047) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
