DLA MIL-DTL-5423 1 F-2009 BOOTS DUST AND WATER SEAL TYPE A (FOR TOGGLE SWITCHES) STYLE 1 (ONE HOLE MOUNTING ENCLOSED) STYLE 1S (RFI-SHIELDED ONE - HOLE MOUNTING ENCLOSED).pdf

上传人:rimleave225 文档编号:690946 上传时间:2018-12-30 格式:PDF 页数:2 大小:51.73KB
下载 相关 举报
DLA MIL-DTL-5423 1 F-2009 BOOTS DUST AND WATER SEAL TYPE A (FOR TOGGLE SWITCHES) STYLE 1 (ONE HOLE MOUNTING ENCLOSED) STYLE 1S (RFI-SHIELDED ONE - HOLE MOUNTING ENCLOSED).pdf_第1页
第1页 / 共2页
DLA MIL-DTL-5423 1 F-2009 BOOTS DUST AND WATER SEAL TYPE A (FOR TOGGLE SWITCHES) STYLE 1 (ONE HOLE MOUNTING ENCLOSED) STYLE 1S (RFI-SHIELDED ONE - HOLE MOUNTING ENCLOSED).pdf_第2页
第2页 / 共2页
亲,该文档总共2页,全部预览完了,如果喜欢就下载吧!
资源描述

1、INCH-POUND MIL-DTL-5423/1F 17 February 2009 SUPERSEDING MIL-DTL-5423/1E 4 February 2008 DETAIL SPECIFICATION SHEET BOOTS, DUST AND WATER SEAL, TYPE A (FOR TOGGLE SWITCHES), STYLE 1 (ONE HOLE MOUNTING, ENCLOSED) STYLE 1S (RFI-SHIELDED, ONE - HOLE MOUNTING, ENCLOSED) This specification sheet is approv

2、ed for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-5423. Inches mm Inches mm .005 0.13 .219 5.56 .010 0.25 .325 8.26 .020 0.51 .469 11.91 .031 0.79 .625 15.88 .125

3、3.18 .644 16.36 .160 4.06 .844 21.44 SECTION A-A STYLE 1S SECTION A-A STYLE 1 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only and are based upon 1 inch = 25.4 mm. 3. Unless otherwise specified, tolerances are .015 (0.38 mm). FIGURE 1. Boots, type A, s

4、tyle 1 and style 1S. AMSC N/A FSC 5930 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-5423/1F 2 REQUIREMENTS: Dimensions and configuration: See figure 1. Silicon rubber: Grade 50. Restoring force (style 1): 5 inchounces. Watertightness: Inne

5、r constriction test required. Endurance: Style 1: In accordance with MIL-DTL-5423. Style 1S: 15,000 cycles of mechanical operations. Part or Identifying Number (PIN): Style 1: M5423/01-01. Style 1S: M5423/01-02. NOTE: Style 1S Toggle switches selected for use with these boots should have adequate op

6、erating force to avoid any tendency of the boot to return to a position other than that in which it is set. Qualification: First Article Testing in accordance with MIL-DTL-5423. The margins of this specification are marked with vertical lines to indicate where modifications were made. This was done

7、as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations. Referenced documents: MIL-DTL-5423

8、 Custodians: Preparing activity: Army - CR DLA - CC Navy - AS Air Force - 85 (Project 5930-2008-058) DLA - CC Review activities: Army AT, AV, CR4, MI Navy CG, EC, MC, OS Air Force - 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 标准规范 > 国际标准 > 其他

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1