1、 INCH-POUND MIL-DTL-55181/1D 10 March 2008 SUPERSEDING MIL-C-55181/1C 23 June 1986 DETAIL SPECIFICATION SHEET CONNECTOR, PLUG, ELECTRICAL, WATERPROOF, 4 SOCKET CONTACTS, SOLDER TURRET, 35 AMP This specification is approved for use by all Departments and Agencies of the Department of Defense. The req
2、uirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-55181. CONNECTORFIGURE 1. Dimensions and configuration. AMSC N/A FSC 5935 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55181/1D 2 CO
3、NTACT Inches mm Inches mm Inches mm Inches mm .015 .028 .038 .040 .041 .042 .044 .048 .052 .062 0.38 0.71 0.96 1.01 1.04 1.06 1.12 1.22 1.32 1.57 .076 .080 .082 .086 .089 .092 .094 .099 .110 .125 1.93 2.03 2.08 2.18 2.26 2.34 2.38 2.51 2.79 3.17 .184 .190 .233 .235 .250 .275 .375 .406 .466 FIGURE 1.
4、 Dimensions and configuration - Continued. .074 1.88 .176 4.47 .470 .513 4.67 4.82 5.92 5.97 6.35 6.99 9.52 10.31 11.83 11.93 13.03 .519 .625 .925 .995 1.000 1.095 1.103 1.470 1.585 2.125 2.500 13.18 15.87 23.49 25.27 25.40 27.81 28.01 37.34 40.26 53.97 63.50 Provided by IHSNot for ResaleNo reproduc
5、tion or networking permitted without license from IHS-,-,-MIL-DTL-55181/1D 3 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified tolerances are .005 inch (0.13 mm) for three place decimals and .01 inch (0.3 mm) for two place decimal
6、s. 4. Angular tolerances are 30 minutes unless otherwise specified. 5. See table l for cable size accommodations. FIGURE 1 Dimensions and configuration - Continued. REQUIREMENTS: Dimensions and configuration: See figure 1 and table I. Contacts: 35 ampere current rating, 12 AWG. Part or Identifying N
7、umber (PIN): M55181/1 - (dash number as specified in table I). TABLE I. Dash number, cross reference and mating connector. Cable size accommodation Mating connector PIN Type designator 1/MIN MAX PIN Type designator 1/M55181/1-01 M55181/1-02 M55181/1-03 M55181/1-04 M55181/1-05 MW10F(M)A11 MW10F(M)A13
8、 MW10F(M)A17 MW10F(M)A19 MW10F(M)A15 .292 (7.42) .323 (8.20) .448 (11.38) .511 (12.98) .386 (9.80) .343 (8.71) .406 (10.31) .531 (13.48) .593 (15.06) .468 (11.88) M55181/2-01 M55181/2-01 M55181/2-01 M55181/2-01 M55181/2-01 MW20M(M)A00 MW20M(M)A00 MW20M(M)A00 MW20M(M)A00 MW20M(M)A00 1/ This type desi
9、gnator shall not be referenced for procurement purposes. Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever f
10、or any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Provided by IHSNot for ResaleNo reproduction or networking permi
11、tted without license from IHS-,-,-MIL-DTL-55181/1D 4 CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 11 DLA - CC (Project 5935-2007-121) Review activity: Air Force - 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
