1、AMSC N/A FSC 5920 MIL-DTL-83413/10C SUPERSEDING 19 May 2010 MIL-DTL-83413/10B 31 March 2005 DETAIL SPECIFICATION SHEET CONNECTORS AND ASSEMBLIES, ELECTRICAL, AIRCRAFT GROUNDING: JUMPER CABLE ASSEMBLY, AIRCRAFT TO FUEL NOZZLE, DISCHARGER, ELECTROSTATIC This specification is approved for use by all De
2、partments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-83413. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specifie
3、d, tolerance is .016 ( 0.041 mm). 4. The cap on this assembly is not used on plug PIN M83413/4-1. FIGURE 1. Jumper cable assembly. INCH-POUND STUD (SEE FIGURE 3) CAP (SEE FIGURE 2) GROUNDING WIRE FIGURE 2. Cap. (1905 76.2 ) Provided by IHSNot for ResaleNo reproduction or networking permitted without
4、 license from IHS-,-,-MIL-DTL-83413/10C 2 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. FIGURE 2. Cap Continued. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. FIGURE 3. Stud. Inches mm .010 .25 .0
5、62 1.57 .078 1.98 .237 6.02 .250 6.35 .310 7.87 .406 10.31 .875 22.23 .893 22.68 Inches mm .062 1.57 .332 8.43 .469 11.91 .500 12.70 .625 15.87 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83413/10C 3 REQUIREMENTS Grounding plug In accorda
6、nce with MIL-DTL-83413/4. Grounding wire 7 X 7 wire in accordance with MIL-DTL-83420, type II, composition B, jacket color translucent or international orange in accordance with FED-STD-595/22510. Splices shall not be used. Part or Identifying Number (PIN): M83413/10-1 is the assembly, see figure 1.
7、 M83413/10-2 is the cap, see figure 2. QUALIFICATION Qualification is not required for this specification sheet. First article inspection shall be a visual and mechanical inspection in accordance with MIL-DTL-83413. Certain provisions of this specification are the subject of International Standardiz
8、ation Agreements AIR-STD 25/26 and NATO STANAG 3632. When revision or cancellation of this specification is proposed which wilt affect or violate the international agreements concerned, the preparing activity will take appropriate reconciliation action through international standardization channels,
9、 including departmental standardization offices, if required. Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoe
10、ver for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced documents. In addition to MIL-DTL-83413, this do
11、cument references the following: MIL-DTL-83413/4 MIL-DTL-83420 FED-STD-595/22510 AIR-STD 25/26 NATO STANAG 3632 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83413/10C 4 CONCLUDING MATERIAL Custodians: Preparing activity: Army - AV DLA - CC
12、 Navy - AS Air Force - 85 (Project 5920-2010-011) DLA - CC Review activities: Army - AR, CR, CR4, MI Navy - MC Air Force 99 Note: The activities listed above were interested in this document as of the date of this document. Since organization and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
