1、 INCH-POUND MIL-DTL-83513/13D 6 March 2009 SUPERSEDING MIL-DTL-83513/13C 20 September 2002 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, RECTANGULAR, RECEPTACLE, MICROMINIATURE, POLARIZED SHELL, RIGHT ANGLE, SOCKET CONTACTS, 2 ROW, SOLDER TYPE, NARROW PROFILE, 9 THROUGH 37 CONTACTS, PRINTED CIR
2、CUIT BOARD This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-83513. FIGURE 1. Connector, receptacle, .050 spacing. AMSC N/A FSC 5935 Pr
3、ovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/13D 2 Inches mm Inches mm .003 .0038 .010 .015 .025 .050 .0671 .096 0.08 0.096 0.25 0.38 0.635 1.27 1.704 2.44 .130 .144 .150 .185 .1852 .190 .250 .325 3.30 3.66 3.81 4.70 4.704 4.83 6.35 8.
4、23 FIGURE 1. Connector, receptacle, .050 spacing - Continued.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/13D 3 Number of contacts A Max B .005 D E Max F Max G .01 H Max 9 .787 (19.99) .565 (14.35) .3342 (8.49) .425 (10.80) .425 (10.
5、80) .230 (5.84) .787 (19.99) 15 .937 (23.80) .715 (18.16) .4842 (12.30) .425 (10.80) .425 (10.80) .130 (3.30) .937 (23.80) 21 1.087 (27.61) .865 (21.97) .6342 (16.11) .425 (10.80) .425 (10.80) .130 (3.30) 1.087 (27.61) 25 1.187 (30.15) .965 (24.51) .7342 (18.65) .425 (10.80) .425 (10.80) .130 (3.30)
6、 1.187 (30.15) 31 1.337 (33.96) 1.115 (28.32) .8842 (22.46) .450 (11.43) .525 (13.34) .130 (3.30) 1.090 (27.69) 37 1.487 (37.77) 1.265 (32.13) 1.0342 26.27) .450 (11.43) .525 (13.34) .130 (3.30) 1.190 (30.23) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3
7、. Unless otherwise specified, tolerances are .005 (0.13 mm). 4. Termination organization area to be optionally molded or filled with a potting fill material capable of passing the electrical and environmental requirements of MIL-DTL-83513. Plastic molding shall conform to type GDI-30F or type SDG-F
8、in accordance with ASTM D5948 or GCT-30F in accordance with ASTM D5927 or MIL-M-24519 or GST-40F in accordance with ASTM D4067 or MIL-M-24519 or GLCP-30F or GLCP-50 in accordance with ASTM D5138 or MIL-M-24519. 5. Metal shell shall be of material in accordance with MIL-DTL-83513 for class M parts. 6
9、. Jackpost (securely attached) when specified: Corrosion resistant steel in accordance with ASTM A484/A484M and ASTM A582/A582M, 300 series stainless steel, passivated in accordance with SAE-AMS-2700, type 2. Hardware will be attached in such a fashion as to not loosen during normal de-mating condit
10、ions, where as, the mating connector hardware does not exceed the following torque values: 2.5 inch pounds for #2-56 (arrangements A - G) and 4.5 inch pounds for #4-40 (arrangement H). 7. Separately molded plastic body (if used) shall conform to type GDI-30F or type SDG-F in accordance with ASTM D59
11、48 or GCT-30F in accordance with ASTM D5927 or MIL-M-24519 or GST-40F in accordance with ASTM D4067 or MIL-M-24519 or GLCP-30F or GLCP-50 in accordance with ASTM D5138 or MIL-M-24519. 8. Wire termination sockets shall conform to A-A-59551, no. 24 AWG copper, except shall be tin-lead plated with a mi
12、nimum of 3 percent lead. 9. Interfacial seals are included with each type receptacle connector. 10. Termination lengths available: .109 (2.77 mm), .140 (3.56 mm), or .172 (4.37 mm). The tolerance shall be .015 (0.38 mm) for all termination lengths. 11. Threaded insert, when specified: Corrosion resi
13、stant steel in accordance with ASTM A484/A484M and ASTM A582/A582M, 300 series stainless steel, passivated in accordance with SAE-AMS-2700, type 2. FIGURE 1. Connector, receptacle, .050 spacing - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS
14、-,-,-MIL-DTL-83513/13D 4 NOTE: Engaging face of socket insert shown, cavity identification numbers are for reference only and do not appear on the part. FIGURE 2. Insert arrangement.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/13D 5
15、Inches mm Inches mm Inches mm .020 0.51 .100 2.54 .715 18.16 .040 1.02 .108 2.74 .865 21.97 .050 1.27 .158 4.01 .965 24.51 .083 2.11 .183 4.65 1.115 28.32 .096 2.44 .565 14.35 1.265 32.13 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise sp
16、ecified, tolerance is .005 (0.13 mm) on decimals. FIGURE 3. Layout arrangement. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/13D 6 FIGURE 3. Layout arrangement - Continued. Provided by IHSNot for ResaleNo reproduction or networking p
17、ermitted without license from IHS-,-,-MIL-DTL-83513/13D 7 FIGURE 3. Layout arrangement - Continued.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/13D 8 REQUIREMENTS: Dimensions and configurations: See figures 1, 2 and 3. Current rating
18、, maximum: 3 amperes per contact. Materials: Termination organization area: Potting fill material capable of passing the electrical and environmental requirements of MIL-DTL-83513. Shell: The requirements for shell materials shall be in accordance with MIL-DTL-83513. Plastic body or plastic molding:
19、 Shall conform to the requirements of GDI-30F or type SDG-F in accordance with ASTM D5948 or GCT-30F in accordance with ASTM D5927 or MIL-M-24519 or GST-40F in accordance with ASTM D4067 or MIL-M-24519 or GLCP-30F or GLCP-50 in accordance with ASTM D5138 or MIL-M-24519. Jackpost: Corrosion resistant
20、 steel in accordance with ASTM A484/A484M and ASTM A582/A582M, 300 series stainless steel, passivated in accordance with SAE-AMS-2700, type 2. Wire termination pins: Wire termination pins shall conform to A-A-59551, no. 24 AWG copper, except shall be tin-lead plated with a minimum of 3 percent lead.
21、 Mating connector: Shall conform to MIL-DTL-83513/1 and MIL-DTL-83513/3. Plating of termination leads: Solder dipping of termination leads will be accomplished in SN60 PB40 or SN63 PB37 in accordance with J-STD-006. Part or Identifying Number (PIN): PIN shall consist of the letter M, the basic numbe
22、r of the specification sheet, a letter from the insert, a numerical code for the termination length, and a letter code for the shell finish and hardware column. M83513/13- D 01 A P Specification sheet number Insert arrangements (see figure 2) Termination length Shell finish (interface critical) Hard
23、ware A = 09 B = 15 01 = .109 02 = .140 A = Pure electrodeposited aluminum N = No hardware or threaded insert P = jackpost attach C = 21 03 = .172 C = Cadmium T = threaded insert D = 25 K = Zinc nickel W = jackpost and threaded insert E = 31 N = electroless nickel F = 37 (space applications only) P =
24、 Passivated Stainless Steel T = Nickel fluorocarbon polymer Changes from previous issue: The margins of this specification are marked with vertical lines to indicate where changes from previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever fo
25、r any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Provided by IHSNot for ResaleNo reproduction or networking permit
26、ted without license from IHS-,-,-MIL-DTL-83513/13D 9 Referenced documents. In addition to MIL-DTL-83513, this document references the following: MIL-DTL-83513/1 ASTM A484/A484M A-A-59551 MIL-DTL-83513/3 ASTM A582/A582M J-STD-006 MIL-M-24519 ASTM D4067 SAE-AMS-2700 ASTM D5138 ASTM D5927 ASTM D5948 CO
27、NCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 85 (Project 5935-2007-061) NASA - NA DLA - CC Review activities: Army - AT, MI Navy - AS, CG, MC, SH Air Force - 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
