1、 INCH-POUND MIL-DTL-83513/26D 18 March 2009 SUPERSEDING MIL-DTL-83513/26C 27 February 2003 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, RECTANGULAR, RECEPTACLE, MICROMINIATURE, POLARIZED SHELL, STRAIGHT, SOCKET CONTACTS, 3 ROW, SOLDER TYPE, 51 CONTACTS, PRINTED CIRCUIT BOARD This specification
2、 is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-83513. FIGURE 1. Connector receptacle, .050 spacing. AMSC N/A FSC 5935 Provided by IHSNot for ResaleNo
3、reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/26D 2Inches mm Inches mm Inches mm Inches mm .003 0.08 .0671 1.70 .185 4.70 1.215 30.86 .007 0.18 .096 2.44 .190 4.83 1.775 45.09 .0038 0.097 .130 3.30 .2282 5.796 2.000 50.80 .015 0.38 .144 3.66 .351 8.92 2.280 57.91 .0
4、25 0.64 .150 3.81 .355 9.02 .050 1.27 .165 4.19 .9842 24.999 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerances are .005 inch (0.13 mm). 4. Termination organization area to be optionally molded or filled with a potting
5、fill material capable of passing the electrical and environmental requirements of MIL-DTL-83513. Plastic molding shall conform to type GDI-30F or type SDG-F in accordance with ASTM D5948 or GCT-30F in accordance with ASTM D5927 or MIL-M-24519 or GST-40F in accordance with ASTM D4067 or MIL-M-24519 o
6、r GLCP-30F or GLCP-50 in accordance with ASTM D5138 or MIL-M-24519. 5. Metal shell shall be of material in accordance with MIL-DTL-83513 for class M parts. 6. Jackpost (securely attached) when specified: Corrosion resistant steel in accordance with ASTM A484/A484M and ASTM A582/A582M, 300 series sta
7、inless steel, passivated in accordance with SAE-AMS-2700, type 2. Hardware will be attached in such a fashion as to not loosen during normal de-mating conditions, where as, the mating connector hardware does not exceed the following torque values: 2.5 inch pounds for #2-56 (arrangements A G) and 4.5
8、 inch pounds for #4-40 (arrangement H). 7. Separately molded plastic body (if used) shall conform to type GDI-30F or type SDG-F in accordance with ASTM D5948 or GCT-30F in accordance with ASTM D5927 or MIL-M-24519 or GST-40F in accordance with ASTM D4067 or MIL-M-24519 or GLCP-30F or GLCP-50 in acco
9、rdance with ASTM D5138 or MIL-M-24519 8. Wire termination pins shall conform to A-A-59551, number 24 AWG copper, except shall be tin-lead plated with a minimum of 3 percent lead. 9. Interfacial seals are included with each type receptacle connector. 10. Termination lengths available: .109 inch (2.77
10、 mm), .140 inch (3.56 mm), or .172 inch (4.37 mm). The tolerance shall be .015 inch (0.38 mm) for all termination lengths. 11. Threaded insert, when specified: Corrosion resistant steel in accordance with ASTM A484/A484M and ASTM A582/A582M, 300 series stainless steel, passivated in accordance with
11、SAE-AMS-2700, type 2. FIGURE 1. Connector receptacle, .050 spacing - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/26D NOTE: Engaging face of socket insert shown, cavity identification numbers are for reference only and do
12、not appear on the part. FIGURE 2. Insert arrangement. Inches mm .040 1.02 .050 1.27 .096 2.44 .100 2.54 .150 3.81 2.000 50.80 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are for information only. FIGURE 3. Layout arrangement. 3Provided by IHSNot for ResaleNo reproduction or networking
13、permitted without license from IHS-,-,-MIL-DTL-83513/26D 4REQUIREMENTS: Dimensions and configurations: See figures 1, 2 and 3. Current rating, maximum: 3 amperes per contact. Materials: Termination organization area: Potting fill material capable of passing the electrical and environmental requireme
14、nts of MIL-DTL-83513. Shell: The requirements for shell materials shall be in accordance with MIL-DTL-83513. Plastic body or plastic molding: Shall conform to the requirements of GDI-30F or type SDG-F in accordance with ASTM D5948 or GCT-30F in accordance with ASTM D5927 or MIL-M-24519 or GST-40F in
15、 accordance with ASTM D4067 or MIL-M-24519 or GLCP-30F or GLCP-50 in accordance with ASTM D5138 or MIL-M-24519. Jackpost: Corrosion resistant steel in accordance with ASTM A484/A484M and ASTM A582/A582M, 300 series stainless steel, passivated in accordance with SAE-AMS-2700, type2. Wire termination
16、pins: Wire termination pins shall conform to A-A-59551, no. 24 AWG copper, except shall be tin-lead plated with a minimum of 3 percent lead. Mating connector: Shall conform to MIL-DTL-83513/1 and MIL-DTL-83513/3. Plating of termination leads: Solder dipping of termination leads will be accomplished
17、in SN60 PB40 or SN63 PB37 in accordance with J-STD-006. Part or Identifying Number (PIN): PIN shall consist of the letter M, the basic number of the specification sheet, a letter from the insert, a numerical code for the termination length, and a letter code for the shell finish and hardware column.
18、 M83513/26- G 01 C P Specification sheet number Insert arrangements (see figure 2) Termination length Shell finish (interface critical) Hardware G = 51 01 = .109 02 = .140 A = Pure electrodeposited aluminum N = No hardware or threaded insert P = jackpost attach 03 = .172 C = Cadmium T = threaded ins
19、ert K = Zinc nickel W = jackpost and threaded insert N = electroless nickel (space applications only) P = Passivated Stainless Steel T = Nickel fluorocarbon polymer CHANGES FROM PREVIOUS ISSUE: The margins of this specification are marked with vertical lines to indicate where changes from previous i
20、ssue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and r
21、elationship to the last previous issue. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/26D 5Referenced documents. In addition to MIL-DTL-83513, this document references the following: MIL-DTL-83513/1 ASTM A484/A484M A-A-59551 MIL-DTL-8
22、3513/3 ASTM A582/A582M J-STD-006 MIL-M-24519 ASTM D4067 SAE-AMS-2700 ASTM D5138 ASTM D5927 ASTM D5948 CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 85 (Project: 5935-2007-074) NASA - NA DLA - CC Review activities: Army - AT, MI Navy - AS, CG, MC, SH Air
23、 Force 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
