1、AMSC N/A FSC 5935 MIL-DTL-83513/31B INCH-POUND18 March 2009 SUPERSEDING MIL-DTL-83513/31A 24 May 2004 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, RECTANGULAR, RECEPTACLE, MICROMINIATURE, POLARIZED SHELL, STRAIGHT, SOCKET CONTACTS, 2 ROW, SOLDER TYPE, STANDARD PROFILE, 9 THROUGH 37 CONTACTS, P
2、RINTED CIRCUIT BOARD This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-83513. Inches mm .0038 0.10 .005 0.127 .010 0.25 .014 0.36 .015
3、0.38 .020 0.51 .025 0.64 .030 0.076 .050 1.27 .0671 1.704 .088 2.24 .096 2.44 .129 3.28 .130 3.30 .144 3.66 .150 3.81 .1848 4.694 .185 4.70 .1852 4.704 .190 4.83 .310 7.87 .355 9.02 FIGURE 1. Connector, receptacle. Provided by IHSNot for ResaleNo reproduction or networking permitted without license
4、from IHS-,-,-MIL-DTL-83513/31B 2 FIGURE 1. Connector, receptacle - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/31B 3 Number of contacts A Max B .005 (0.13) D 9 .785 (19.94) .565 (14.35) .3342 (8.489) 15 .935 (23.75) .715
5、18.16) .4842 (12.299) 21 1.085 (27.56) .865 (21.97) .6342 (16.109) 25 1.185 (30.01) .965 (24.51) .7342 (18.649) 31 1.335 (33.91) 1.115 (28.32) .8842 (22.459) 37 1.485 (37.72) 1.265 (32.13) 1.0342 (26.269) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. U
6、nless otherwise specified, tolerances are +.005 (0.13 mm). 4. Termination organization area to be optionally molded or filled with a potting fill material capable of passing the electrical and environmental requirements of MIL-DTL-83513. Plastic molding shall conform to type GDI-30F or type SDG-F in
7、 accordance with ASTM D5948 or GCT-30F in accordance with ASTM D5927 or MIL-M-24519 or GST-40F in accordance with ASTM D4067 or MIL-M-24519 or GLCP-30F or GLCP-50 in accordance with ASTM D5138 or MIL-M-24519. 5. Metal shell shall be of material in accordance with MIL-DTL-83513 for class M parts. 6.
8、Jackpost (securely attached) when specified: Corrosion resistant steel in accordance with ASTM A484/A484M and ASTM A582/A582M, 300 series stainless steel, passivated in accordance with SAE-AMS-2700, type 2. Hardware will be attached in such a fashion as to not loosen during normal de-mating conditio
9、ns, where as, the mating connector hardware does not exceed the following torque values: 2.5 inch pounds for #2-56 (arrangements A G) and 4.5 inch pounds for #4-40 (arrangement H). 7. Separately molded plastic body (if used) shall conform to type GDI-30F or type SDG-F in accordance with ASTM D5948 o
10、r GCT-30F in accordance with ASTM D5927 or MIL-M-24519 or GST-40F in accordance with ASTM D4067 or MIL-M-24519 or GLCP-30F or GLCP-50 in accordance with ASTM D5138 or MIL-M-24519. 8. Wire termination pins shall conform to A-A-59551, number 24 AWG copper, except shall be tin-lead plated with a minimu
11、m of 3 percent lead. 9. Interfacial seals are included with each type receptacle connector. 10. Termination lengths available: .109 (2.77 mm), .140 (3.56 mm), or .172 (4.37 mm). The tolerance shall be +.015 (0.38 mm) for all termination lengths. 11. Threaded insert, when specified: Corrosion resista
12、nt steel in accordance with ASTM A484/A484M and ASTM A582/A582M, 300 series stainless steel, passivated in accordance with SAE-AMS-2700, type 2. FIGURE 1. Connector, receptacle - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-8351
13、3/31B 4 FIGURE 2. Insert arrangement. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/31B 5 NOTE: Engaging face of pin insert shown, cavity identification numbers are for reference only and do not appear on the part. FIGURE 2. Insert ar
14、rangement - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/31B 6 FIGURE 3. Layout arrangement. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/31B 7 FIGURE 3. L
15、ayout arrangement - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/31B 8 Inches mm Inches mm Inches mm .025 0.64 .183 4.65 .715 18.16 .038 0.97 .200 5.08 .750 19.05 .040 1.02 .225 5.72 .865 21.97 .050 1.27 .350 8.89 .900 22.
16、86 .075 1.91 .500 12.70 .965 24.51 .096 2.44 .565 14.35 1.115 28.32 .100 2.54 .600 15.42 1.265 32.13 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are for information only. 3. Unless otherwise specified, tolerances are .005 (0.13 mm). 4. Patterns shown are for connector mounting side of
17、PC board. FIGURE 3. Layout arrangement - Continued. REQUIREMENTS: Dimensions and configurations: See figures 1, 2 and 3. Current rating, maximum: 3 amperes per contact. Materials: Termination organization area: Potting fill material capable of passing the electrical and environmental requirements of
18、 MIL-DTL-83513. Shell: The requirements for shell materials shall be in accordance with MIL-DTL-83513. Plastic body or plastic molding: Shall conform to the requirements of GDI-30F or SDG-30F of ASTM D5948, or GPT-30F or GET-30F or GCT-30F of ASTM D5927 or MIL-M-24519 or GST-40F of ASTM D4067 or MIL
19、M-24519 or GLCP-30F or GLCP-50F in accordance with ASTM D5138 or MIL-M-24519. Jackpost: Corrosion resistant steel in accordance with ASTM A484/A484M and ASTM A582/A582M, 300 series stainless steel, passivated in accordance with SAE-AMS-2700, type 2. Wire termination pins: Wire termination pins shal
20、l be in accordance with A-A-59551, number 24 AWG copper or shall be of a single piece contact with a tail of suitable conductive copper based alloys, except shall be tin-lead plated with a minimum of 3 percent lead. Mating connector: Shall be in accordance with MIL-DTL-83513/1 and MIL-DTL-83513/3. P
21、lating of termination leads: Solder dipping of termination leads will be accomplished in SN60 PB40 or SN63 PB37 in accordance with J-STD-006. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/31B 9 Part or Identifying Number (PIN): The PI
22、N shall consist of the letter M, the basic number of the specification sheet, a letter from the insert, a numerical code for the termination length, and a letter code for the shell finish and hardware column. M83513/31- A 01 C P Specification sheet number Insert arrangements (see figure 2) Terminati
23、onlength Shell finish (interface critical) Hardware A = 09 B = 15 C = 21 01 = .109 02 = .140 03 = .172 A = Pure electrodeposited aluminum C = Cadmium N = No hardware or threaded insert P = jackpost attach D = 25 K = Zinc nickel T = threaded insert E = 31 N = electroless nickel W = jackpost and threa
24、ded insertF = 37 (space applications only) P = Passivated Stainless SteelT = Nickel fluorocarbon polymer Changes from previous issue: The margins of this specification are marked with vertical lines to indicate where changes from previous issue were made. This was done as a convenience only and the
25、Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced documents
26、 In addition to MIL-DTL-83513, this document references the following: MIL-DTL-83513/1 ASTM A484/A484M A-A-59551 MIL-DTL-83513/3 ASTM A582/A582M J-STD-006 MIL-M-24519 ASTM D4067 SAE-AMS-2700 AST D5138 ASTM D5927 AST D5948 Provided by IHSNot for ResaleNo reproduction or networking permitted without
27、license from IHS-,-,-MIL-DTL-83513/31B 10 CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 85 (Project: 5935-2007-079) NASA - NA DLA - CC Review activities: Army - AT, CR4, MI Navy - AS, CG, MC, SH Air Force - 99 NOTE: The activities listed above were inte
28、rested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
