1、MIL-DTL-83528/13F 13 August 2013 SUPERSEDING MIL-DTL-83528/13E 15 November 2001 DETAIL SPECIFICATION SHEET GASKETING MATERIAL, CONDUCTIVE, SHIELDING GASKET, ELECTRONIC, ELASTOMER, ELECTRICAL, EMI/RFI, WAVEGUIDE This specification sheet is approved for use by all Departments and Agencies of the Depar
2、tment of Defense. The requirements for acquiring the relay described herein shall consist of this specification sheet and the latest issue of MIL-DTL-83528. TABLE I. Selection guide (see figures 1-5 for configurations and dimensions). Frequency range (GHz) Band EIA wave- guide size Waveguide designa
3、tion per MIL-DTL-85Flange designation per MIL-DTL-3922 Flange type Gasket config- uration Part or Identifying Number (PIN)M83528/013XUG CPR CMR26.5-40.0 KaWR28 RG-96/U (Silver) UG-599/U Cover A 001 1/ UG-600A/U Choke E 002 18.0-26.5 K WR42 RG-53/U (Brass) UG-595/U UG-597/U Cover A 003 1/ RG-121/U (A
4、luminum) UG-596A/U UG-598A/U Choke E 004 12.4-18.0 KuWR62 RG-91 (Brass) UG-419/U Cover A 005 1/ RG-107/U (Silver) UG-541A/U Choke E 006 10.0-15.0 WR75 Cover A 007 Choke E 008 8.2-12.4 X WR90 RG-52/U (Brass) RG-67/U (Aluminum) UG-39/U UG-135/U Cover A 009UG-1736/U UG-1737/U CPR-90F Flat contact A 010
5、 1/ UG-136A/U UG-40A/U Choke E 011 UG-136B/U UG-40B/U Choke E 012 UG-1360/U UG-1361/U CPR-90G Contact C 013 7.0-11.0 WR102 UG-1494/U Choke E 014 7.05-10.0 X1WR112 RG-51/U (Brass) RG-68/U (Aluminum) UG-51/U UG-138/U Cover A 015UG-1734/U UF-1735/U CPR-112F Flat contact A 016 1/ UG-52B/U UG-137B/U Chok
6、e E 017 UG-1358/U UF-1359/U CPR-112G Contact C 018 See footnote at end of table. AMSC N/A FSC 5999 INCH-POUNDProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83528/13F 2 TABLE I. Selection guide (see figures 1 - 5 for configurations and dimens
7、ions) - Continued. Frequency range (GHz) Band EIA wave- guide size Waveguide designation per MIL-DTL-85Flange designation per MIL-DTL-3922 Flange type Gasket config- uration Part or Identifying Number (PIN) M83528/013X UG CPR CMR 5.85-8.2 XbWR137 RG-50/U (Brass) RG-106/U (Aluminum) UG-334/U UG-441/U
8、 Cover B 019 UG-1732/UUG-1733/UCPR-137FFlat contact 020 1/ CMR-137 Flat contact A 021 1/ UG-343B/UUG-440B/UChoke D 022 UG-1356/UUG-1357/UCPR-137GContact C 023 4.9-7.05 WR159 UG-1730/UUG-1731/UCPR-159F Flat contact A 024 1/ CMR-149 Flat contact A 025 1/ 3.95-5.85 C WR187 RG-49/U (Brass) RG-95/U (Alum
9、inum) UG-149A/UUG-407/U Cover B 026 UG-1728/UUG-1729/UCPR-187FFlat contact A 027 1/ CMR-187 Flat contact A 028 1/ UG-148C/UUG-406B/UChoke D 029 UG-1352/UUG-1353/UCPR-187GContact C 030 3.30-4.90 WR229 UG-1726/UUG-1727/UCPR-229F Flat contact A 031 1/ CMR-229 Flat contact A 032 1/ 2.6-3.95 S WR284 RG-4
10、8/U (Brass) RG-75/U (Aluminum) UG-53/U UG-584/U Cover B 033 1/ UG-1724/UUG-1725/UCPR-284FFlat contact A 034 1/ CMR-284 Flat contact A 035 1/ UG-54B/U UG-585A/UChoke E 036 UG-1348/UUG-1349/UCPR-284GContact C 037 2.2-3.3 WR340 RG-112U (Brass) RG-112/U (Aluminum) UG-533/U UG-554/U Flat contact A 038 1/
11、 CPR-340F Flat contact A 039 1/ 1.7-2.6 W WR340 RG-104/U (Brass) RG-105/U (Aluminum) UG-435A/UUG-437A/UFlat contact A 040 1/ CPR-430F Flat contact A 041 1/ 1.12-1.7 L WR650 RG-69/U (Brass) RG-103/U (Aluminum) UG-417A/UUG-418A/UFlat contact A 042 1/ 1/ This gasket will seal a maximum pressure of 20 p
12、sig. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83528/13F 3 CONFIGURATION A DIE CUT SQUARE AND RECTANGULAR NOTE: Shaded area indicates optional raised lip. When included, the lip shall be a nominal of .187 (4.75 mm) wide. Thickness T1sha
13、ll be .004 (0.10 mm) .002 (0.05 mm). Lip is standard on configuration A dash numbers without footnote 1/ reference in table I. For dash numbers in table I with footnote 1/ reference, lip is optional. Dimensions (Configuration A) Part or Identifying Number (PIN) M83528/013X Cross section area (cm2) 2
14、/ A .015 (0.38) B .015 (0.38) C .015 (0.38) -.000 (0.00) D .015 (0.38) -.000 (0.00) E 1/ .010 (0.25) T .003 (0.08) F Radius .010 (0.25) .750 (19.05) .750 (19.05) .145 (3.68) .285 (7.24) .116 (2.95) .027 (0.69) .469 (11.91) 001 .0082 .875 (22.23) .875 (22.23) .175 (4.45) .425 (10.80) .116 (2.95) .027
15、 (0.69) .563 (14.30) 003 .0095 1.313 (33.35) 1.313 (33.35) .630 (16.00) .320 (8.13) .140 (3.56) .027 (0.69) .875 (22.23) 005 .0095 1.496 (38.00) 1.496 (38.00) .760 (19.30) .385 (9.78) .155 (3.94) .027 (0.69) .450 (11.43) 007 .0099 1.625 (41.28) 1.625 (41.28) .905 (22.99) .405 (10.29) .169 (4.29) .02
16、7 (0.69) .469 (11.91) 009 .0097 1.594 (40.49) 2.094 (53.19) .405 (10.29) .905 (22.99) .169 (4.29) .027 (0.69) .250 (6.35) 010 .0161 1.875 (47.63) 1.875 (47.63) 1.130 (28.70) .505 (12.83) .180 (4.57) .027 (0.69) 1.15 (29.21) 015 .0101 1.750 (44.45) 2.500 (63.50) .505 (12.83) 1.130 (28.70) .171 (4.34)
17、 .027 (0.69) .250 (6.35) 016 .076 1.937 (49.20) 2.687 (68.25) .633 (16.08) 1.380 (35.05) .206 (5.23) .027 (0.69) .250 (6.35) 020 .0176 1.531 (38.89) 2.281 (57.94) .632 (16.05) 1.382 (35.10) .150 (3.81) .027 (0.69) .125 (3.18) 021 .0121 2.438 (61.93) 3.188 (80.98) .805 (20.45) 1.600 (40.64) .257 (6.5
18、3) .027 (0.69) .313 (7.95) 024 .0220 See footnotes at end of table. FIGURE 1. Configuration A dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83528/13F 4 Dimensions (Configuration A) Part or Identifying Number (PIN) M83528/013X Cr
19、oss section area (cm2) 2/ A .015 (0.38) B .015 (0.38) C .015 (0.38) -.000 (0.00) D .015 (0.38) -.000 (0.00) E 1/ .010 (0.25) T .003 (0.08) F Radius .010 (0.25) 1.750 (44.45) 2.500 (63.50) .800 (20.32) 1.600 (40.64) .160 (4.06) .150 (3.81) .027 (0.69) .125 (3.18) 025 .0128 3.500 (88.90) 2.500 (63.50)
20、 1.880 (47.75) .880 (22.35) .266 (6.76) .027 (0.69) .313 (7.95) 027 .0219 1.784 (45.31) 2.781 (70.64) .882 (22.40) 1.882 (47.80) .156 (3.96) .141 (3.58) .027 (0.69) .125 (3.18) 028 .0122 2.750 (69.85) 3.875 (98.43) 1.155 (29.34) 2.300 (58.42) .270 (6.86) .027 (0.69) .312 (7.92) 031 .0215 2.000 (50.8
21、0) 3.156 (80.16) 1.155 (29.34) 2.300 (58.42) .150 (3.81) .027 (0.69) .125 (3.18) 032 .0114 4.500 (114.30) 3.000 (76.20) 2.850 (72.39) 1.350 (34.29) .266 (6.76) .027 (0.69) .313 (7.95) 034 .0223 3.844 (97.64) 2.344 (59.54) 2.850 (72.39) 1.350 (34.29) .172 (4.37) .188 (4.78) .027 (0.69) .125 (3.18) 03
22、5 .0134 3.750 (95.25) 5.440 (138.18) 1.710 (43.43) 3.410 (86.61) .264 (6.71) .250 (6.35) .027 (0.69) .250 (6.35) 038 .0275 3.750 (95.25) 5.438 (138.13) 1.710 (43.43) 3.410 (86.61) .266 (6.76) .027 (0.69) .250 (6.35) 039 .0275 4.188 (106.38) 6.344 (161.14) 2.160 (54.86) 4.310 (109.47) .266 (6.76) .28
23、1 (7.14) .027 (0.69) .250 (6.35) 040 .0274 6.344 (161.14) 4.188 (106.38) 4.310 (109.47) 2.160 (54.86) .266 (6.76) .027 (0.69) .250 (6.35) 041 .0275 5.438 (138.13) 8.688 (220.68) 3.260 (82.80) 6.510 (165.35) .250 (6.35) .328 (8.33) .027 (0.69) .250 (6.35) 042 .0294 1/ Number and location of holes con
24、form to holes in standard waveguide flanges identified in table I. Where two hole diameters are given, flange has holes of two different diameters. 2/ For calculation of volume resistivity (surface probe). FIGURE 1. Configuration A dimensions Continued. Provided by IHSNot for ResaleNo reproduction o
25、r networking permitted without license from IHS-,-,-MIL-DTL-83528/13F 5 CONFIGURATION B DIE CUT CIRCULAR NOTE: Shaded area indicates optional raised lip. When included, the lip shall be a nominal of .187 (4.75 mm) wide. Thickness T1shall be .004 (0.10 mm) .002 (0.05 mm). Lip is standard on configura
26、tion B dash numbers without footnote 1/ reference in table I. For dash numbers in table I with footnote 1/ reference, lip is optional. Dimensions (Configuration B) Part or Identifying Number (PIN) M83528/013X Cross section area (cm2) 2/ A .015 (0.38) B .015 (0.38) -0.000 (0.00) C .015 (0.38) -0.000
27、0.00) D 1/ .010 (0.25) T .005 (0.13) 3.125 (79.38) .632 (16.05 1.382 (35.10) .234 (5.94) .027 (0.69) 019 .0337 3.625 (92.08) .882 (22.40) 1.882 (47.80) .234 (5.94) .027 (0.69) 026 .0370 5.312 (134.92) 1.350 (34.29) 2.850 (72.39) .290 (7.37) .027 (0.69) 033 .0535 1/ Number and location of holes conf
28、orm to holes in standard waveguide flanges identified in table I. 2/ For calculation of volume resistivity (surface probe). FIGURE 2. Configuration B dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83528/13F 6 CONFIGURATION C MOLD
29、ED RECTANGULAR WITH “O” CROSS SECTION NOTE: Molding flash of .003 (0.08 mm) in width (maximum) and .005 (0.13 mm) in thickness (maximum) is allowed. Dimensions (Configuration C) Part or Identifying Number (PIN) M83528/013X Cross section area (cm2) 1/ A B T dia 1.368 (34.75) .012 (0.03) .868 (22.05)
30、010 (0.25) .103 (2.62) .003 (0.08) 013 .0538 1.616 (41.05) .015 (0.38) .991 (25.17) 0.010 (0.25) .103 (2.62) .003 (0.08) 018 .0538 1.866 (41.05) .015 (0.38) 1.116 (28.35) .012 (0.30) .103 (2.62) .003 (0.08) 023 .0538 2.449 (62.20) .020 (0.51) 1.449 (36.80) .013 (0.33) .139 (3.53) .004 (0.10) 030 .0
31、979 3.451 (87.66) .024 (0.61) 1.951 (49.56) .018 (0.46) .139 (3.53) .004 (0.10) 037 .0979 1/ For calculation of volume resistivity (surface probe). FIGURE 3. Configuration C dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83528/13
32、F 7 CONFIGURATION D MOLDED CIRCULAR WITH “O” CROSS SECTION NOTE: Molding flash of .003 (0.08 mm) in width (maximum) and .005 (0.13 mm) in thickness (maximum) is allowed. Dimensions (Configuration D) Part or Identifying Number (PIN) M83528/013X Cross section area (cm2) 1/ D (ID) T 2.011 (51.08) .018
33、0.46) .139 (3.53) .004 (0.10) 022 .0979 2.683 (68.15) .024 (0.61) .115 (2.92) .004 (0.10) 029 .0670 1/ For calculation of volume resistivity (surface probe). FIGURE 4. Configuration D dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-D
34、TL-83528/13F 8 CONFIGURATION E MOLDED CIRCULAR WITH “D” CROSS SECTION NOTE: Molding flash of .003 (0.08 mm) in width (maximum) and .005 (0.13 mm) in thickness (maximum) is allowed. Dimensions (Configuration E) Part or Identifying Number (PIN) M83528/013X Cross section area (cm2) 1/ A B D (ID) T .056
35、 (1.42) .041 (1.04) .410 (10.41) .082 (2.08) 002 .025.048 (1.22) .039 (0.99) .587 (14.91) .078 (1.98) 004 .020.125 (3.18) .078 (1.98) .885 (22.48) .155 (3.94) 006 .109 .065 (1.65) .049 (1.24) 1.122 (28.50) .099 (2.51) 008 .035.088 (2.24) .048 (1.22) 1.340 (34.04) .095 (2.41) 011 .048 .077 (1.96) .05
36、8 (1.47) 1.310 (33.27) .115 (2.92) 012 .048.085 (2.16) .048 (1.22) 1.392 (35.36) 0.95 (2.41) 014 .046 .078 (2.16) .053 (1.35) 1.550 (39.37) .105 (2.67) 017 .045.188 (4.78) .120 (3.05) 3.910 (99.31) .026 (0.66) .240 (6.10) 036 .251 1/ For calculation of volume resistivity (surface probe). NOTES: 1. D
37、imensions are in inches/ metric equivalents are given in parenthesis and are for general information only. 2. Unless otherwise indicated, tolerances shall be as follows: Dimensions Tolerance Under Over .101 (2.57) .101 to .200 (2.57 to 5.08) .201 to .300 (5.10 to 7.62) .301 to .500 (7.62 to 12.70) .
38、500 (12.70) .005 (0.13) .008 (0.20) .010 (0.25) .015 (0.38) .020 (0.51) FIGURE 5. Configuration E dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83528/13F 9 SELECTION GUIDE: See table I. REQUIREMENTS: Design and interface: See fi
39、gures 1-5 and table I. Materials: Configuration A: Type G. Configuration B: Type G. Configuration C: Types C, F, H, or K. Configuration D: Types C, F, H, or K. Configuration E: Types C, F, H, or K. Part or Identifying Number (PIN): See table I and figures 1-5. An “X” in the PIN represents the materi
40、al type (see above). PIN example: M83528/013G001. Gaskets with optional high-pressure raised lip (see table I and figures 1-5) will have a “Z” added to their PINs. Example: M83528/013G001Z. Supersession information: See table II. TABLE II. Supersession information. 1/ MIL-G-83528/13B PIN M83528/013X
41、 Superseded MIL-G-83528/13A PIN M83528/013X Superseded DESC drawing PIN 85118X 002 001 001004 002 002006 003 003008 004 004 012 005 005011 006 006014 007 007017 008 008036 009 009 1/ “X” in the PIN indicates the applicable material type. Changes from previous issue. The margins of this specification
42、 are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this docu
43、ment based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced documents. In addition to MIL-DTL-83528, this document references the following: MIL-DTL-85 MIL-DTL-3922 Provided by IHSNot for ResaleNo reproduction or networking permitte
44、d without license from IHS-,-,-MIL-DTL-83528/13F 10 Custodians: Preparing activity: Army CR DLA CC Navy EC Air Force 85 (Project 5999-2013-010) DLA CC Review activities: Air Force 19, 99 NASA NA NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
