1、 MIL-DTL-83723/80D 1 October 2010 SUPERSEDING MIL-DTL-83723/80C 20 October 2000 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, (CIRCULAR, ENVIRONMENT RESISTING), RECEPTACLE, (SOLDER OR WELD FLANGE MOUNT, BAYONET COUPLING, SOLDER PIN CONTACT), (SERIES III, CLASSES H, J, L, P AND Y) This specifica
2、tion is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-83723. FIGURE 1. Dimensions and configurations. AMSC N/A FSC 5935INCH-POUND Provided by IHSNot for
3、ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/80D 2 FIGURE 1. Dimensions and configurations - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/80D 3 Shell size C D E F S +.005 -.000 V
4、 W FF GG 8 .428 .433 .312 .536 .531 .561 .508 .500 .760 .720 .505 .515 .406 10 .530 .535 .388 .659 .654 .696 .636 .562 .860 .820 .567 .577 .443 12 .700 .705 .558 .829 .824 .875 .806 .750 1.065 1.025 .755 .765 .668 14 .769 .774 .627 .898 .893 .935 .875 .812 1.110 1.070 .817 .827 .668 16 .896 .901 .77
5、2 1.025 1.020 1.062 1.002 .937 1.230 1.190 .942 .952 .763 18 1.002 1.007 .860 1.131 1.126 1.187 1.108 1.062 1.360 1.320 1.067 1.077 .862 20 1.127 1.132 .985 1.256 1.251 1.312 1.233 1.187 1.450 1.410 1.192 1.202 1.108 22 1.252 1.257 1.110 1.381 1.376 1.437 1.358 1.312 1.610 1.570 1.317 1.327 1.204 24
6、 1.377 1.382 1.235 1.506 1.501 1.562 1.483 1.437 1.730 1.690 1.442 1.452 1.388 FIGURE 1. Dimensions and configurations - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/80D 4 Inches mm Inches mm Inches mm Inches mm Inches mm
7、003 0.08 .330 8.38 .636 16.15 .901 22.89 1.251 31.78 .004 0.10 .366 9.30 .654 16.61 .935 23.75 1.252 31.80 .005 0.13 .376 9.55 .659 16.74 .937 23.80 1.256 31.90 .015 0.38 .378 9.60 .668 16.97 .942 23.93 1.257 31.93 .018 0.48 .380 9.65 .696 17.68 .952 24.18 1.312 33.32 .020 0.51 .388 9.86 .700 17.78
8、 .985 25.02 1.317 33.45 .022 0.56 .392 9.96 .705 17.92 1.002 25.45 1.320 33.53 .032 0.81 .400 10.16 .720 18.29 1.007 25.58 1.327 33.71 .048 1.22 .406 10.31 .734 18.64 1.020 25.91 1.332 33.83 .062 1.57 .428 10.87 .750 19.05 1.025 26.04 1.358 34.49 .071 1.80 .433 11.00 .755 19.18 1.062 26.97 1.360 34.
9、54 .076 1.93 .443 11.25 .760 19.30 1.065 27.05 1.376 34.95 .078 1.98 .490 12.45 .763 19.38 1.067 27.10 1.377 34.98 .084 2.13 .500 12.70 .765 19.43 1.070 27.18 1.381 35.08 .089 2.26 .505 12.83 .769 19.53 1.077 27.36 1.382 35.10 .090 2.29 .508 12.90 .772 19.61 1.108 28.14 1.388 35.26 .094 2.39 .515 13
10、08 .774 19.66 1.110 28.19 1.410 35.81 .097 2.46 .530 13.46 .806 20.47 1.126 28.60 1.437 36.50 .101 2.57 .531 13.49 .812 20.62 1.127 28.63 1.442 36.63 .106 2.69 .535 13.51 .820 20.83 1.131 28.73 1.450 36.83 .108 2.74 .536 13.61 .824 20.93 1.132 28.75 1.452 36.88 .112 2.84 .540 13.72 .827 21.01 1.187
11、 30.15 1.483 37.67 .138 3.51 .558 14.17 .829 21.06 1.190 30.23 1.501 38.13 .144 3.66 .560 14.22 .860 21.84 1.192 30.28 1.506 38.25 .198 5.03 .561 14.25 .862 21.98 1.202 30.53 1.562 39.67 .204 5.18 .562 14.27 .875 22.23 1.204 30.58 1.570 39.89 .225 5.72 .567 14.40 .893 22.68 1.230 31.24 1.610 40.89 .
12、259 6.58 .577 14.66 .896 22.76 1.233 31.32 1.690 42.93 .312 7.92 .627 15.93 .898 22.81 1.235 31.37 1.730 43.94 NOTES: (Notes 4 through 8 apply to contacts only). 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerances are .005 inch
13、es (0.13 mm) for three place decimal, .01 inches (0.25 mm) for two place decimals, and 1 for all angles. 4. Dimensions apply after plating. 5. Surface finish: 63 ( ) all over in accordance with ASME-B46.1, unless otherwise specified. 6. Remove all burrs and sharp edges .003 to .005 inches (0.076 to
14、0.127 mm) R. 7. Diameters to be concentric within .004 inches (0.102 mm) TIR. 8. Diameter in the same cross-sectional plane to be concentric with each other within .003 inches (0.076 mm) TIR. 9. See table I for contact cavities requiring this dimension. FIGURE 1. Dimensions and configurations - Cont
15、inued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/80D 5 REQUIREMENTS: Dimensions and configurations: See figure 1. This connector mates with MIL-DTL-83723/75 and MIL-DTL-83723/77. For insert arrangements, see MIL-STD-1554 and table
16、 I. TABLE I. Insert arrangements requiring reduced diameters for raised seal barriers on contact cavities as indicated. Shell size Insert arrangements Contact cavities 8 03, 98 1, 2, and 3 10 06 1, 2, 3, 4, 5, and 6 Connector accessories: See SAE-AS85049. Part or Identifying Number (PIN) example: M8
17、3723/ 80 H 22 55 N Military designation Specification sheet number Class Shell size Insert arrangement Polarizing position Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced
18、 documents. In addition to MIL-DTL-83723, this document references the following: MIL-DTL-83723/75 MIL-DTL-83723/77 MIL-STD-1554 ASME-B46.1 SAE-AS85049 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/80D 6 CONCLUDING MATERIAL Custodians
19、 Preparing activity: Army - CR DLA - CC Navy - AS Air Force 85 (Project 5935-2010-049) DLA - CC Review activities: Army - AR, MI Navy - EC Air Force - 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
