1、 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, (CIRCULAR, ENVIRONMENT RESISTING), PLUG, (RFI, THREADED COUPLING, CRIMP PIN CONTACT), (SERIES III, CLASSES G, M, R, T, W AND Z) This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements fo
2、r acquiring the product described herein shall consist of this specification sheet and MIL-DTL-83723. FIGURE 1. Dimensions and configurations. AMSC N/A FSC 5935 INCH-POUND MIL-DTL-83723/92D 1 October 2009 SUPERSEDING MIL-C-83723/92C 24 April 1992 Provided by IHSNot for ResaleNo reproduction or netwo
3、rking permitted without license from IHS-,-,-MIL-DTL-83723/92D 2 FIGURE 1. Dimensions and configurations - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/92D 3 Shell size A Thread UNEF-2B B C H min J K W max 8 .5625-24 .290
4、7.37) .025 (.64) .294 (7.47) .405 (10.29) .396 (10.06) .575 (14.61) .776 (19.71) 10 .6875-24 .388 (9.86) .031 (.79) .428 (10.87) .526 (13.36) .517 (13.13) .707 (17.96) .906 (23.01) 12 .875-20 .558 (14.17) .598 (15.19) .696 (17.68) .687 (17.45) .895 (22.73) 1.078 (27.38) 14 .9375-20 .627 (15.93) .66
5、7 (16.94) .765 (19.43) .756 (19.20) .957 (24.31) 1.141 (28.98) 16 1.0625-18 .772 (19.61) .794 (20.17) .892 (22.66) .883 (22.43) 1.084 (27.53) 1.266 (32.16) 18 1.1875-18 .860 (21.84) .900 (22.86) .998 (25.35) .989 (25.12) 1.209 (30.71) 1.375 (34.93) 20 1.3125-18 .985 (25.02) 1.025 (26.04) 1.123 (28.5
6、2) 1.114 (28.30) 1.334 (33.88) 1.510 (38.35) 22 1.4375-18 1.110 (28.19) 1.150 (29.21) 1.248 (31.70) 1.239 (31.47) 1.459 (37.06) 1.625 (41.28) 24 1.5625-18 1.235 (31.37) 1.275 (32.39) 1.373 (34.87) 1.364 (34.65) 1.584 (40.23) 1.760 (44.70) FIGURE 1. Dimensions and configurations - Continued. Provided
7、 by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/92D 4 Inches mm Inches mm Inches mm Inches mm .005 0.13 .144 3.66 .598 15.19 1.078 27.38 .007 0.18 .198 5.03 .627 15.93 1.084 27.53 .008 0.20 .204 5.18 .667 16.94 1.110 28.19 .015 0.38 .215 5.46 .
8、675 17.15 1.114 28.29 .018 0.46 .235 5.97 .687 17.45 1.123 28.52 .020 0.51 .243 6.17 .691 17.55 1.141 28.98 .022 0.56 .260 6.60 .696 17.68 1.150 29.21 .025 0.64 .290 7.37 .707 17.96 1.180 29.97 .031 0.79 .294 7.47 .756 19.20 1.209 30.71 .032 0.81 .330 8.38 .765 19.43 1.235 31.37 .035 0.89 .388 9.86
9、772 19.61 1.239 31.47 .042 1.07 .396 10.05 .776 19.01 1.248 31.70 .046 1.17 .400 10.16 .794 20.17 1.266 32.15 .048 1.22 .405 10.29 .860 21.84 1.275 32.39 .065 1.65 .428 10.87 .883 22.43 1.334 33.88 .068 1.73 .433 11.00 .892 22.66 1.364 34.65 .069 1.75 .479 12.17 .895 22.73 1.373 34.87 .084 2.13 .50
10、0 12.70 .900 22.86 1.375 34.93 .090 2.29 .510 12.95 .906 23.01 1.459 37.06 .097 2.46 .517 13.13 .957 24.31 1.510 38.35 .101 2.57 .526 13.36 .985 25.02 1.584 40.23 .106 2.69 .558 14.71 .998 25.35 1.625 41.28 .112 2.84 .575 14.60 1.025 26.03 1.760 44.70 .125 3.18 .138 3.51 NOTES: 1. Dimensions are in
11、inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerances are .005 (0.13 mm) for three place decimals and .01 (0.25 mm) for two place decimals and 1 for all angles. 4. The dimensions showing the relationship between the coupling ring and shell apply only
12、 when the coupling ring is in the fully forward position. 5. Rear accessory interchangeability dimensions shall be in accordance with MIL-DTL-83723. 6. Shell size 8 will not mate with MIL-DTL-26500 connectors. 7. The centerline of indicated projection must be located on vertical centerline 2. 8. See
13、 table I for contact cavities requiring this dimension. FIGURE 1. Dimensions and configurations - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/92D 5 REQUIREMENTS: Dimensions and configurations: See figure 1. This connector
14、 mates with MIL-DTL-83723/82 and MIL-DTL-83723/84. Insert arrangements and polarizing positions: See MIL-STD-1554 and table I. TABLE I. Insert arrangements requiring reduced diameters for raised seal barriers on contact cavities. Shell size Insert arrangements Contact cavities 8 03 1, 2, 3 10 06 1,
15、2, 3, 4, 5, 6 Connector accessories: See SAE-AS85049. Part or Identifying Number (PIN) example: M83723/ 92 R 22 55 N Military designation Specification sheet number Class Shell size Insert arrangement Polarizing position Changes from previous issue. Marginal notations are not used in this revision t
16、o identify changes with respect to the previous issue, due to the extent of the changes. Referenced documents. In addition to MIL-DTL-83723, this document references the following: MIL-STD-1554 MIL-DTL-26500 MIL-DTL-83723/82 MIL-DTL-83723/84 SAE-AS85049 Provided by IHSNot for ResaleNo reproduction o
17、r networking permitted without license from IHS-,-,-MIL-DTL-83723/92D 6 CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA - CC Navy - AS Air Force - 85 DLA - CC Review activities: (Project 5935-2008-169) Army - AR, MI Navy - EC Air Force - 19, 99 NOTE: The activities listed above wer
18、e interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
