1、 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, (CIRCULAR, ENVIRONMENT RESISTING), PLUG, (THREADED COUPLING, SELF-LOCKING, CRIMP SOCKET CONTACT), (SERIES III, CLASSES A, G, K, M, R, T, W AND Z) This specification is approved for use by all Departments and Agencies of the Department of Defense. T
2、he requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-83723. FIGURE 1. Dimensions and configurations. AMSC N/A FSC 5935 INCH-POUND MIL-DTL-83723/95G 1 October 2009 SUPERSEDING MIL-DTL-83723/95F 15 September 2006 Provided by IHSNot for Resale
3、No reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/95G 2 FIGURE 1. Dimensions and configurations - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/95G 3 Shell size A Thread UNEF-2B B max C H mi
4、n J K W max 8 .5625-24 .290 (7.37) .025 (.64) .294 (7.47) .405 (10.29) .396 (10.06) .575 (14.61) .832 (21.13) 10 .6875-24 .388 (9.86) .031 (.79) .428 (10.87) .526 (13.36) .517 (13.13) .707 (17.96) .959 (24.36) 12 .875-20 .558 (14.17) .031 (.79) .598 (15.19) .696 (17.68) .687 (17.45) .895 (22.73) 1.0
5、97 (27.86) 14 .9375-20 .627 (15.93) .031 (.79) .667 (16.94) .765 (19.43) .756 (19.20) .957 (24.31) 1.236 (31.39) 16 1.0625-18 .772 (19.61) .031 (.79) .794 (20.17) .892 (22.66) .883 (22.43) 1.084 (27.53) 1.360 (34.54) 18 1.1875-18 .860 (21.84) .031 (.79) .900 (22.86) .998 (25.35) .989 (25.12) 1.209 (
6、30.71) 1.473 (37.41) 20 1.3125-18 .985 (25.02) .031 (.79) 1.025 (26.04) 1.123 (28.52) 1.114 (28.30) 1.334 (33.88) 1.586 (40.28) 22 1.4375-18 1.110 (28.19) .031 (.79) 1.150 (29.21) 1.248 (31.70) 1.239 (31.47) 1.459 (37.06) 1.703 (43.26) 24 1.5625-18 1.235 (31.37) .031 (.79) 1.275 (32.39) 1.373 (34.87
7、) 1.364 (34.65) 1.584 (40.23) 1.846 (46.89) FIGURE 1. Dimensions and configurations - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/95G 4 Inches mm Inches mm Inches mm Inches mm .005 0.13 .290 7.37 .707 17.96 1.114 28.29 .0
8、07 0.18 .294 7.47 .756 19.20 1.123 28.52 .025 0.64 .309 7.85 .765 19.43 1.150 29.21 .031 0.79 .330 8.38 .772 19.61 1.180 29.97 .035 0.89 .366 9.30 .794 20.17 1.1875 30.16 .048 1.22 .377 9.58 .832 21.13 1.209 30.71 .051 1.30 .388 9.86 .860 21.84 1.235 31.37 .054 1.37 .396 10.05 .875 22.23 1.236 31.39
9、 .068 1.73 .400 10.16 .880 22.35 1.239 31.47 .076 1.93 .405 10.29 .883 22.43 1.248 31.70 .092 2.34 .428 10.87 .892 22.66 1.275 32.39 .096 2.44 .500 12.70 .895 22.73 1.334 33.88 .107 2.71 .510 12.95 .900 22.86 1.360 34.54 .114 2.90 .517 13.13 .9375 23.81 1.364 34.65 .118 3.00 .526 13.36 .957 24.31 1.
10、373 34.87 .125 3.18 .528 14.71 .959 24.36 1.4375 36.51 .146 3.71 .5625 14.29 .985 25.02 1.459 37.06 .150 3.81 .575 14.60 .989 25.12 1.5625 39.69 .206 5.23 .598 15.19 .998 25.35 1.584 40.23 .210 5.33 .627 15.93 1.025 26.03 1.586 40.28 .215 5.46 .667 16.94 1.0625 26.99 1.703 43.26 .235 5.97 .675 17.15
11、 1.084 27.53 1.846 46.89 .260 6.60 .6875 17.46 1.097 27.86 .263 6.68 .696 17.68 1.110 28.19 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerances are .005 (0.13 mm) for three place decimals and .01 (0.25 mm) for two place
12、decimals and 1 for all angles. 4. The dimensions showing the relationship between the coupling ring and connector shell apply only when the coupling ring is in the fully forward position. 5. Rear accessory interchangeability dimensions shall be in accordance with MIL-DTL-83723. 6. Shell size 8 will
13、not mate with MIL-DTL-26500 connectors. 7. The centerline of indicated projection must be located on vertical centerline 2.0. 8. See table I for contact cavities requiring this dimension. FIGURE 1. Dimensions and configurations - Continued. Provided by IHSNot for ResaleNo reproduction or networking
14、permitted without license from IHS-,-,-MIL-DTL-83723/95G 5 REQUIREMENTS: Dimensions and configurations: See figure 1. This connector mates with MIL-DTL-83723/83, MIL-DTL-83723/85, MIL-DTL-83723/90 and MIL-DTL-83723/88 and MIL-DTL-83723/89. Insert arrangements and polarizing positions: See MIL-STD-15
15、54 and table I. TABLE I. Insert arrangements requiring reduced diameters for lead-in chamfers on contact cavities. Shell size Insert arrangements Contact cavities 8 03 1, 2, 3 10 06 1, 2, 3, 4, 5, 6 Connector accessories: See SAE-AS85049. Part or Identifying Number (PIN) example: M83723/ 95 K 22 55
16、N Military designation Specification sheet number Class Shell size Insert arrangement Polarizing position Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue, due to the extent of the changes. Referenced documents. In a
17、ddition to MIL-DTL-83723, this document references the following: MIL-STD-1554 MIL-DTL-26500 MIL-DTL-83723/83 MIL-DTL-83723/85 MIL-DTL-83723/88 MIL-DTL-83723/89 MIL-DTL-83723/90 SAE-AS85049 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-8372
18、3/95G 6 CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA - CC Navy - AS Air Force - 85 DLA - CC Review activities: (Project 5935-2008-170) Army - AR, MI Navy - EC Air Force - 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
