1、 MIL-PRF-1/689G 3 February 2012 SUPERSEDING MIL-PRF-1/689F 6 July 1999 PERFORMANCE SPECIFICATION SHEET ELECTRON TUBES, CATHODE RAY TYPES 5ADP1, 5ADP2, 5ADP7 AND 5ADP14 This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring
2、the electron tube described herein shall consist of this document and the latest issue of MIL-PRF-1. DESCRIPTION: Electrostatic deflection and focus with post accelerator. DIMENSIONS AND PIN CONNECTIONS: See figure 1. ABSOLUTE RATINGS: Parameter: Ef Ec1 ed Eb1 Eb2 Eb3 Rg Zd Eb3 Eb2 Ehk Alt Unit: V V
3、 dc v V dc V dc V dc Meg Meg Ratio V dc ft Maximum: All 6.9 0, -200 550 1,100 2,850 6,600 1.5 1.0 2.3 180 50,000 Minimum: P1 5.7 - - - - - - - - - 1,500 1,500 - - - - - - - - - - - - - - - P2, P7, P14 5.7 - - - - - - - - - 1,500 3,000 - - - - - - - - - - - - - - - Test conditions: P1 6.3 Adjust - -
4、- Focus 1,500 3,000 - - - - - - - - - - - - - - - P2, P7 P14 6.3 Adjust - - - Focus 2,000 4,000 - - - - - - - - - - - - - - - _ GENERAL: Qualification - Required. This specification sheet uses accept on zero defect sampling in accordance with MIL-PRF-1, table III. AMSC N/A FSC 5960 INCH-POUND Provid
5、ed by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-1/689G 2 TABLE 1. Testing and inspection. Requirement or Test Method MIL-STD-1311 Type Conditions Symbol Limits Min Limits Max Units Qualification inspection Pressure (implosion) Barometric pressure,
6、reduced Vibration Direct-interelectrode capacitance Neck and bulb alignment (electrostatic types) Cathode illumination Focusing voltage at modulation condition Deflection factor Deflection factor Deflection-factor uniformity Base material insulation quality 1141 1002 5111 1331 5101 5216 5246 5248 52
7、48 5248 1216 All All All All All All P1 P2, P7, P14 P1 P2, P7, P14 P1 P2, P7, P14 All All 87 4 mmHg g1 to all k to all D1 to D2 D3 to D4 D1 to all except D2 D2 to all except D1 D3 to all except D4 D4 to all except D3 1D2; Eb2 = Eb3 = 1,500 V dc 1D2; Eb2 = Eb3 = 2,000 V dc 3D4; Eb2 = Eb3 = 1,500 V dc
8、 3D4; Eb2 = Eb3 = 2,000 V dc - - - - - - Width Cg1 Ck C1D2 C3D4 CD1 CD2 CD3 CD4 dia - - - Eb1 Eb1 DF DF DF DF - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 300 400 32.5 43 24.5 32.5 - - - - - - - - - - - - 1 7.9 5.8 3.1 1.3 6.1 6.1 5.0 5.0 2.25 - - - 515 6
9、90 39.5 53 30.5 40.5 2.0 - - - - - - - - - mm pF pF pF pF pF pF pF pF inch - - - V dc V dc V dc/in. V dc/in. V dc/in. V dc/in. % - - - Conformance inspection, part 1 Bulb, screen and faceplate quality Voltage breakdown Voltage breakdown (electrostatic types) Gas “cross” 5106 5201 5201 5206 All All A
10、ll P1 P2, P7, P14 Light = 15 fL Ib3 = 50 A dc (See note 1) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - See notes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-1/689G 3 TABLE 1. Testing and inspec
11、tion -Continued. Requirement or test Method MIL-STD-1311 Type Conditions Symbol Limits Min Limits Max Units Conformance inspection, part 1 -Continued Light output Modulation Modulation Spot position (electrostatic deflection) Spot displacement (leakage) Grid-cutoff voltage Grid No. 1 leakage current
12、 Grid No. 2 leakage current Total scan Pattern distortion 5221 5223 5223 5231 5231 5241 5251 5251 - - - 5103 P1 P1 P2, P7, P14 All All P1 P2, P7, P14 P1 P2, P7, P14 All (See note 1) Light = 15 fL (See note 1) Ib3 = 50 A dc (See note 1) Focused raster light = 15 fL (See note 2) Focused raster Ib3 = 5
13、0 A dc (See note 2) (See note 4) Light Ec Ec - - - displ Eco Eco - - - - - - - - - - - - - - - 15 - - - - - - - - - - - - -34 -45 - - - - - - 4.25 4.25 - - - - - - 45 55 16 10 -56 -75 - - - - - - - - - - - - - - - fL V dc V dc mm mm V dc V dc - - - - - - inch inch - - - Conformance inspection, part2
14、 Secureness of base, cap or insert Heater or filament current Electrode currents (anode No. 1) Electrode currents (cathode) Electrode currents (cathode) Base alignment (electrostatic types) 1101 1301 5201 5201 5201 5101 All All All P1 P2, P7, P14 All Ec1 = 0 Light = 15 fL Ib3 = 50 A dc + 1D2; pin No
15、.5 - - - If Ib1 Ik Ik - - - - - - 540 -15 - - - - - - - - - - - - 660 10 1,000 1,000 - - - - - - mA A dc A dc A dc - - - See notes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-1/689G 4 TABLE 1. Testing and Inspection -Cont
16、inued. Requirement or test Method MIL-STD-1311 Type Conditions Symbol Limits Min Limits Max Units Conformance inspection, part 2-Continued. Side terminal alignment (electrostatic types) Neck and base alignment (electrostatic types) Angle between traces Stray light emission (conventional types) Scree
17、ns Base pin solder depth Line width A (electrostatic deflection) Line width B (electrostatic deflection) Focusing voltage at cutoff Deflection factor Deflection factor Heater-cathode leakage current Permanence of marking 5101 5101 5101 5216 5221 1111 5226 5226 5246 5248 5248 5251 1105 All All All Al
18、l P2, P7, P14 All P1 P2, P7, P14 P1 P2, P7, P14 P1 P2, P7, P14 P1 P2, P7, P14 P1 P2, P7, P14 All All + 1D2 Eb2 = 2,850 V dc; Eb3 = 6,600 V dc (See note 1) Light = 15 fL Ib3 = 50 A dc Light = 15 fL (See note 3) Ib3 = 50 A dc 1D2 1D2 3D4 3D4 - - - - - - - - - - - - - - - - - - width width width width
19、Eb1 Eb1 DF DF DF DF - - - - - - - - - - - - 89 - - - - - - - - - - - - - - - - - - - - - 345 460 40 54 30.5 40.5 - - - - - - - - - - - - 91 - - - - - - - - - 0.75 0.8 0.8 0.9 515 690 50 66 37.5 50.0 - - - - - - - - - - - - Degrees - - - - - - - - - mm mm mm mm V dc V dc V dc/in. V dc/in. V dc/in. V
20、dc/in. - - - - - - See notes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-1/689G 5 TABLE 1. Testing and inspection -Continued. Requirement or test Method MIL-STD-1311 Type Conditions Symbol Limits Min Limits Max Units Conf
21、ormance inspection, part 3 Life-test provisions Life-test end points - - - - - - All P1 P2, P7, P14 P1 P2, P7, P14 Group C; Eb2 = 2,850 V dc; Eb3 = 6,600 V dc; t = 500 hours Light = 15 fL Ib3 = 30 A dc Light = 11 fL Line width A Line width B Modulation Heater-cathode leakage current Grid No. 1 leaka
22、ge current Grid No. 2 leakage current Stray light emission Ib3 = 37.5 A dc Line width A Line width B Modulation Heater-cathode leakage current Grid No. 1 leakage current Grid No. 2 leakage current Stray light emission - - - - - - - - - - - - width width Ec - - - - - - - - - - - - - - - width width E
23、c - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 0.75 0.85 45 - - - - - - - - - - - - - - - 0.8 0.9 55 - - - - - - - - - - - - - - - - - - - - - - - - mm mm V dc - - - - - - - - - - - -
24、 - - - mm mm V dc - - - - - - - - - - - - NOTES: 1. This test to be performed at the conclusion of the holding period. 2. The scan from the tube face center to the extinction points of focused raster shall be 2.125 inches (53.98 mm). 3. Measure line width B at a distance from the center of the scree
25、n equal to 33 percent of the maximum bulb diameter. The applied astigmatism voltage shall be equal to zero volt. 4. With a raster pattern the size of which is adjusted so that the widest points of the pattern just touch the sides of a square 3.075 inches (78.11 mm) on a side, no point on these patte
26、rn sides will lie within a square 2.925 inches (74.30 mm) on a side, and having the same center as the first square. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-1/689G 6 NOTES: 1. Dimensions are in inches with metric equivalents (in mm) f
27、or comparison. 2. Useful screen radius. 3. Reference dimensions are for information only and are not required for inspection purposes. FIGURE 1. Outline drawing of electron tube types 5ADP1, 5ADP2, 5ADP7 AND 5ADP14. Dimensions Ltr Inches Millimeters Min Max Min Max Qualification inspection L Bulb co
28、ntact: J1-22 M Base: B12-37 Conformance inspection, part 2 A 16.563 16.938 420.70 430.23 B 5.156 5.344 130.96 135.75 C 1.938 2.063 49.23 52.40 D 2.250 R 57.15 F 6.000 6.500 152.40 165.10 G 2.063 2.563 52.40 65.10 H 10 10 Reference Dimensions (see note 3) E 10.281 261.14 J 27.813R 706.14 K 0.875 22.2
29、3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-1/689G 7 Referenced documents. In addition to MIL-PRF-1, this specification sheet references MIL-STD-1311. The margins of this specification are marked with vertical lines to indicate where ch
30、anges from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the
31、 marginal notations and relationship to the last previous issue. Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 99 (Project 5960-2011-023) DLA - CC Review activities: Army - AR, CE Navy - AS, CG, MC, OS NOTE: The activities listed above were interested in this document as o
32、f the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
