1、 MIL-PRF-15160/63F 2 November 2011 MIL-PRF-15160/63E 17 August 2006 PERFORMANCE SPECIFICATION SHEET FUSES, INSTRUMENT, POWER, AND TELEPHONE (NONINDICATING), STYLE F63 This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring t
2、he product described herein shall consist of this specification sheet and MIL-PRF-15160. FIGURE 1. Style F63, characteristic C. AMSC N/A FSC 5920 INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15160/63F 2 Ltr Inches mm Min Max Min
3、 Max A 5.813 5.937 147.65 150.80 B 3.375 - 85.73 - C 1.000 - 25.40 - D 1.031 - 26.19 - E .715 .785 18.16 19.94 F - 1.312 - 33.32 G .122 .128 3.10 3.25 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. The length of the cylindrical body may be less t
4、han the indicated value if other acceptable interference means (pins through blades, collars, and so forth) are provided to prevent mounting the fuse in a fuseholder that will accommodate a fuse rated in the next lower bracket of current ratings. FIGURE 1. Style F63, characteristic C - Continued. Pr
5、ovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15160/63F 3 REQUIREMENTS: Interface and physical dimensions: See figure 1. Case: Glass melamine. Knifeblade: Brass, copper, bronze, or copper alloy. Finish: Nickel or bright alloy plate, silver pl
6、ated when specified. Terminal strength: Method 211 of MIL-STD-202, test condition E, 2 pound-inch torque. Electrical: Current rating: See table I. Current carrying capacity: 110 percent of rated current. Voltage rating: See table I. Characteristic: Characteristic C only. Overload interrupt: Within 1
7、 hour at 135 percent of rated current; and within 6 minutes at 200 percent. Short circuit interrupt: 200,000 A at 500 V ac (symmetrical), 150,000 A at 500 V dc. Shock: Method 207 of MIL-STD-202, HI shock. Vibration: Method 204 of MIL-STD-202, test condition A (except 5g, 500 Hz). Part or Identifying
8、 Number (PIN): The PIN shall be constructed from table I (e.g., F63C500V70A). TABLE I. Part or Identifying Number. 1/ 1/ For silver plated terminals, the designator “S“ is added after the current rating. Style Characteristic Voltage Current F63 F63 F63 F63 C C C C 500V 500V 500V 500V 70A 80A 90A 100
9、A Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15160/63F 4 VERIFICATION: Qualification inspections: The number of qualification samples required shall be: a. 24 samples maximum current rating of each voltage and design. b. 24 samples minim
10、um current rating of each voltage and design. NOTE: If labels are used, five additional samples of any rating are required. Sample size: The number of group III samples shall be twelve samples each of the maximum and minimum current ratings. The samples shall be divided as shown in table II. TABLE I
11、I. Short circuit test. 1/ A 600 volt ac test voltage may be used. Group C inspection: Group C inspection shall be performed on short circuit current ratings of 5,000 A at 500 V ac; 200,000 A at 500 V ac; and 5,000 A at 500 V dc. The 150,000 A at 500 V dc short circuit current test is not required to
12、 be performed for group C testing. INSPECTION ROUTINE: AC short circuit test: AC short circuit tests shall be performed at the currents shown in table II at not less than 500 volts, single phase, and not greater than 20 percent power factor, lagging. The current shall be applied within plus or minus
13、 10 degrees of the zero point of the voltage wave. DC short circuit test: DC short circuit tests shall be performed at the currents shown in table II at not less than 500 volts. The rate of rise shall be between 25,000,000 and 30,000,000 amperes per second. Cross-reference: For applicable cross-refe
14、rence see table III. The existing stocks of superseded items may be used. When exhausted, the superseding parts shall be used. TABLE III. Cross-reference. Number of samples Short circuit current Test voltage 3 3 3 3 5,000 A 200,000 A 5,000 A 150,000 A 500 V ac 1/ 500 V ac 1/ 500 V dc 500 V dc Supers
15、eding number Superseded numbers for CAGE 81349 96906 F63C500V70A F63C500V80A F63C500V90A F63C500V100A F63H70R0C F63H80R0C F63H90R0C F63H100R0C MS15252-1 MS15252-2 MS15252-3 MS15252-4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15160/63F 5
16、 Referenced documents. In addition to MIL-PRF-15160, this document references the following: MIL-STD-202 The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no lia
17、bility whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Custodians: Preparing activity: Army - CR DLA
18、 - CC Navy - SH Air Force - 85 (Project 5920-2011-061) DLA - CC Review activities: Army - AT, CR4, MI Navy - AS, CG, MC, OS, YD Air Force - 19, 99 DTRA - DS NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
