1、AMSC N/A FSC 5915 MIL-PRF-15733/43E W/AMENDMENT 1 21 April 2008 SUPERSEDING MIL-PRF-15733/43E 17 July 2003 PERFORMANCE SPECIFICATION SHEET FILTERS, RADIO FREQUENCY INTERFERENCE, STYLE FL70 This specification sheet is approved for use by all Depart- ments and Agencies of the Department of Defense. Th
2、e requirements for acquiring the filters described herein shall consist of this specification sheet and MIL-PRF-15733. CLCLCLCLCLCLNOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Circuit diagram is for information only. 4. Recommended mounting tor
3、que: 3 in-lb (-0001) and 6 in-lb (-0002 and -0003) maximum. 5. Mounting hardware (lockwasher and hex nut) will be supplied with each filter. 6. Leads shall be silver coated or solder coated copper. 7. Turret head is optional. FIGURE 1. Case and circuit diagram. Part or Identifying Numbers (PINs) M15
4、733/43-0001 and M15733/43-0002 are inactive for new design after 2 December 1982. For new design use M15733/61-0002 for M15733/43-0001 and M15733/61-0008 for M15733/43-0002. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15733/43E
5、 W/AMENDMENT 1 2 Filter dimensions. Dimension A B C D E Dash number Min Max Min Max Min Max Min Max Min Max 0001 .208 (5.28) .228 (5.79) .271 (6.88) .291 (7.39) .781 (19.84) .843 (21.41) .177 (4.50) .197 (5.00) .349 (8.86) .369 (9.37) 0002 .206 (5.23) .226 (5.74) .256 (6.50) .276 (7.01) .859 (21.82)
6、 .921 (23.39) .083 (2.11) .103 (2.62) .281 (7.14) .343 (8.71) 0003 .203 (5.16) .233 (5.92) .266 (6.76) .296 (7.52) .750 (19.05) .874 (22.20) .172 (4.37) .202 (5.13) .328 (8.33) .390 (9.91) Dimension G H J K L Dash number Min Max Min Max Min Max Thread Min Max 0001 .240 (6.10) .260 (6.60) .050 (1.27)
7、 .070 (1.78) .010 (0.25) .030 (0.76) .216-28 UNF-2A .027 (0.69) .037 (0.94) 0002 .177 (4.50) .197 (5.00) .050 (1.27) .070 (1.78) .010 (0.25) .030 (0.76) .164-32 UNC-2A .027 (0.69) .037 (0.94) 0003 .235 (5.97) .265 (6.73) .050 (1.27) .070 (1.78) .010 (0.25) .030 (0.76) .216-32 UNEF-2A .035 (0.89) .04
8、5 (1.14) Hardware dimensions Hex nut Lockwasher A B C D E F Dash number Min Max Min Max Thread Min Max Min Max Min Max 0001 .240 (6.10) .260 (6.60) .070 (1.78) .080 (2.03) .216-28 UNF-2B .351 (8.92) .369 (9.37) .045 (1.14) .051 (1.30) .219 (5.56) .229 (5.82) 0002 .240 (6.10) .260 (6.60) .073 (1.85)
9、.078 (1.98) .164-32 UNC-2B .263 (6.68) .273 (6.93) .034 (0.86) .038 (0.97) .168 (4.27) .176 (4.47) 0003 .302 (7.67) .322 (8.18) .070 (1.78) .080 (2.03) .216-32 UNEF-2B .371 (9.42) .381 (9.68) .020 (0.51) .024 (0.61) N/A N/A FIGURE 1. Case and circuit diagram - Continued. Provided by IHSNot for Resal
10、eNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15733/43E W/AMENDMENT 1 3 TABLE I. Electrical characteristics. Rated voltage Minimum insertion loss (dB) in accordance with MIL-STD-220 2/ +25C -55C, +125C Dash no. DC volts AC 1/ rms volts Capacitance pF minimum 10 MHz 30
11、 MHz 100 MHz 200 MHz 300 MHz 1-10 GHz 10 MHz 30 MHz 100 MHz 200 MHz 300 MHz 1-10 GHz 0001 3/ 200 140 1500 - - - 45 45 45 - - - 28 45 45 0002 3/ 100 70 1500 - - - 50 50 50 - - - 28 50 50 0003 500 N/A 2500 12 20 45 - 60 70 4 11 25 - 50 70 1/ DC to 400 Hz. 2/ Full-load insertion loss measurements shall
12、 be performed at 10 MHz. Measurements above this frequency shall be performed at no-load. 3/ Inactive for new design. REQUIREMENTS: Design and construction: Dimensions and configuration: See figure 1. Case: Metal. Case and hardware finish: In accordance with MIL-PRF-15733. Pure tin finish is prohibi
13、ted. Weight: 2.6 grams, maximum. Operating temperature range: -55C to +125C. Rated voltage: See table I. Rated current: 10 amperes maximum. Voltage drop: 0.10 volts maximum. Voltage conditioning (conformance inspection only). Voltage conditioning test shall be performed as follows: Test temperature:
14、 125C. Test voltage: 200 percent of the rated dc voltage. Charging current shall not exceed 50 mA. Current load: Not applicable. Points of application of test voltage: Between either terminal and case. Duration of exposure to test voltage: 100 4 hours. Seal: Not applicable. Provided by IHSNot for Re
15、saleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15733/43E W/AMENDMENT 1 4 Capacitance to ground: In accordance with MIL-PRF-15733. The following details shall apply: Test voltage: 0.5 V rms at 25C. Measured capacitance shall be as specified in table I. Temperature ri
16、se: 25C, maximum. Dielectric withstanding voltage: In accordance with MIL-PRF-15733. The following exceptions shall apply: The test voltage shall be three times the rated dc voltage applied for 1 to 5 seconds. Barometric pressure (reduced): In accordance with MIL-PRF-15733. The following exceptions
17、shall apply: Test condition E, Method 105 of MIL-STD-202. Dielectric withstanding voltage: In accordance with initial requirements, except that the test voltage shall be 120 percent of the rated dc voltage applied for 1 to 5 seconds. Insulation resistance: In accordance with MIL-PRF-15733. Insulatio
18、n resistance shall be measured at 25C between either terminal and case, and shall be not less than 10,000 megohms. Insertion loss at +25C and temperature extremes: In accordance with MIL-PRF-15733 and table I. Overload: In accordance with MIL-PRF-15733. The following exception shall apply: Measureme
19、nts at 25C after test: Insulation resistance only shall be measured and shall meet initial requirements. Terminal strength: In accordance with MIL-PRF-15733 and Method 211, MIL-STD-202; test condition A. Applied force: 5 pounds. Salt atmosphere (corrosion): In accordance with MIL-PRF-15733 and Metho
20、d 101, MIL-STD-202; test condition B. Thermal shock and immersion: Not applicable. Shock (specified pulse): In accordance with MIL-PRF-15733 and Method 213, MIL-STD-202; test condition C. Vibration, high frequency: In accordance with MIL-PRF-15733 and Method 204, MIL-STD-202; test condition C. The f
21、ollowing exceptions shall apply: Part 2 of the test shall be 20 gs. Duration shall be 3 hours each in two mutually perpendicular planes. Moisture resistance: Not applicable. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15733/43E W/AMENDMEN
22、T 1 5 Life: In accordance with MIL-PRF-15733 and Method 108, MIL-STD-202; test condition D. The following details and exceptions shall apply: Test voltage: 2 times rated dc voltage with no load at 125C for 1,000 hours. Measurements after test: Dielectric withstanding voltage initial voltage applied
23、for 1 to 5 seconds and shall meet initial requirements. Insulation resistance shall be not less than 1,000 megohms. Capacitance to ground and insertion loss shall be measured and shall meet the initial requirements. Part or Identifying Number (PIN): M15733/43- (dash number from table I and figure 1)
24、. Marking: Each filter shall be marked with the military PIN, as shown on figure 2. In addition, full marking in accordance with method I requirements of MIL-STD-1285 shall be marked on each unit package. FIGURE 2. Hex flats-expanded view, part marking. Conformance inspection: In accordance with MIL
25、-PRF-15733 except as follows: Group A inspection for all dash numbers shall be in accordance with table II. Lots having greater than 10 percent rejects shall be considered reject lots. Reject lots, at the option of the manufacturer, may be reworked and submitted to group A inspection of table II. TA
26、BLE II. Group A inspection. Test or inspection Sampling procedure Voltage conditioning 100% Capacitance to ground 100% Dielectric withstanding voltage 100% Insulation resistance 100% Voltage drop 1/ 100% Insertion loss 100% Visual and mechanical inspection See MIL-PRF-15733, group A inspection 1/ DC
27、 voltage drop/dc resistance test for dc rated filters shall be performed on a sample basis in accordance with MIL-PRF-15733, group A inspection. Application note: These nonhermetically sealed filters may be susceptible to moisture intrusion when subjected to repeated thermal cycling. If these items
28、are to be utilized in applications enduring harsh environments, the user should consider placing them within hermetic enclosures. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15733/43E W/AMENDMENT 1 6 * Referenced documents. In addition to
29、 MIL-PRF-15733, this document also references the following: MIL-STD-202 MIL-STD-220 MIL-STD-1285 * Changes from previous issue. The margins of this specification sheet are marked with asterisks to indicate where changes from the previous issue were made. This was done as a convenience only and the
30、Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Custodians: Preparin
31、g activity: Army - CR DLA - CC Navy - EC Air Force - 11 (Project 5915-2008-014) DLA - CC Review activities: Army - AR, AT, AV, MI Navy - AS, MC, OS Air Force - 19, 99 * NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
