1、 AMSC N/A FSC 59GP INCH-POUNDMIL-PRF-15733/49K 23 April 2009 SUPERSEDING MIL-PRF-15733/49J 10 April 2003 PERFORMANCE SPECIFICATION SHEET FILTERS AND CAPACITORS, RADIO FREQUENCY INTEFERENCE, HERMETICALLY SEALED, STYLE FL93 This specification sheet is approved for use by all Depart- ments and Agencies
2、 of the Department of Defense. * The complete requirements for acquiring the filters described herein shall consist of this specification sheet and MIL-PRF-15733. * FIGURE 1. Case dimensions and circuit diagrams. Part or Identifying Numbers (PINs) M15733/49-0002, 0003, 0004, and 0005 are inactive fo
3、r new design after 6 October 1980. As of 15 March 1993, PIN M15733/49-0006 is inactive for new design. PINs M15733/49-0001 and M15733/49-0007 are inactive for new design after 23 April 2009. For new design see table III for supersession data. Provided by IHSNot for ResaleNo reproduction or networkin
4、g permitted without license from IHS-,-,-* Dash no. A B C D E F G H J K L Min Max Min Max Min Max Min Max Min Max Typ Min Max Slot or hole 010 Mounting thread Max Max 0001 2/ .257 (6.53) .319 (8.10) - .416 (10.57) .177 (4.50) .197 (5.00) .281 (7.14) .343 (8.71) - - .040 (1.02) .190 (4.83) .210 (5.33
5、) - .250-28 UNF-2A - - 0002 2/ .560 (14.22) - - .385 (9.78) .177 (4.50) .197 (5.00) .100 (2.54) - .140 (3.56) - .105 (2.67) .190 (4.83) .210 (5.33) Slot .050 (1.27) .250-28 UNF-2A .387 (9.83) .740 (18.80) 0003 2/ .160 (4.06) - - .385 (9.78) .177 (4.50) .197 (5.00) .140 (3.56) - .100 (2.54) - .105 (2
6、.67) .190 (4.83) .210 (5.33) .060 dia. 1/ (1.52) both ends .250-28 UNF-2A .357 (9.07) .370 (9.40) 0004 2/ .160 (4.06) - - .385 (9.78) .177 (4.50) .197 (5.00) .140 (3.56) - .100 (2.54) - .105 (2.67) .190 (4.83) .210 (5.33) .060 dia. 1/ (1.52) both ends .250-28 UNF-2A .357 (9.07) .370 (9.40) 0005 2/ .
7、210 (5.33) - - .385 (9.78) .302 (7.67) .322 (8.18) .140 (3.56) - .100 (2.54) - .105 (2.67) .190 (4.83) .210 (5.33) .050 x .070 (1.27) x (1.78) or .070 (1.78) dia. .250-28 UNF-2A .482 (12.24) .420 (10.67) 0006 2/ .160 (4.06) - .365 (9.27) .385 (9.78) .177 (4.50) .197 (5.00) .140 (3.56) - .100 (2.54)
8、- .105 (2.67) .190 (4.83) .210 (5.33) .050 x .070 (1.27) x (1.78) or .070 (1.78) dia. .250-28 UNF-2A .357 (9.07) .370 (9.40) 0007 2/ .160 (4.06) - .365 (9.27) .385 (9.78) .177 (4.50) .197 (5.00) .250 (6.35) - .250 (6.35) - .040 (1.02) .190 (4.83) .210 (5.33) - .250-28 UNF-2A .467 (11.86) .450 (11.43
9、) 0008 .406 (10.31) - - .400 (10.16) .180 (4.57) .200 (5.08) .140 (3.56) - .140 (3.56) - - .190 (4.83) .210 (5.33) .050 x .070 (1.27) x (1.78) or .070 (1.78) dia. .250-28 UNF-2A .360 (9.14) .576 (14.63) 0010 .500 (12.70) - - .400 (10.16) .180 (4.57) .200 (5.08) .140 (3.56) - .140 (3.56) - - .190 (4.
10、83) .210 (5.33) .050 x .070 (1.27) x (1.78) or .070 (1.78) dia. .250-28 UNF-2A .360 (9.14) .680 (17.27) MIL-PRF-15733/49K 2 1/ Slot optional. 2/ Inactive for new design. FIGURE 1. Case dimensions and circuit diagrams - ContinuedProvided by IHSNot for ResaleNo reproduction or networking permitted wit
11、hout license from IHS-,-,-MIL-PRF-15733/49K 3 Hex nut Lockwasher A B C D E Filter dash no. Min Max Min Max Thread Min Max Min Max 0001 .302 (7.67) 3.22 (8.18) .085 (2.16) .095 (2.41) .250-28 UNF-2B .396 (10.06) .408 (10.36) .017 (0.43) .027 (0.69) 0002 .307 (7.80) .317 (8.05) .088 (2.24) .098 (2.49)
12、 .250-28 UNF-2B .396 (10.06) .408 (10.36) .017 (0.43) .027 (0.69) 0003 .307 (7.80) .317 (8.05) .088 (2.24) .098 (2.49) .250-28 UNF-2B .396 (10.06) .408 (10.36) .017 (0.43) .027 (0.69) 0004 .307 (7.80) .317 (8.05) .088 (2.24) .098 (2.49) .250-28 UNF-2B .396 (10.06) .408 (10.36) .017 (0.43) .027 (0.69
13、) 0005 .307 (7.80) .317 (8.05) .088 (2.24) .098 (2.49) .250-28 UNF-2B .396 (10.06) .408 (10.36) .017 (0.43) .027 (0.69) 0006 .302 (7.67) .322 (8.18) .085 (2.16) .095 (2.41) .250-28 UNF-2B .396 (10.06) .408 (10.36) .017 (0.43) .027 (0.69) 0007 .302 (7.67) .322 (8.18) .085 (2.16) .095 (2.41) .250-28 U
14、NF-2B .396 (10.06) .408 (10.36) .017 (0.43) .027 (0.69) 0008 .307 (7.80) .317 (8.05) .088 (2.24) .098 (2.49) .250-28 UNF-2B .396 (10.06) .408 (10.36) .017 (0.43) .027 (0.69) 0010 - .317 (8.05) - .098 (2.49) .250-28 UNF-2B .396 (10.06) .408 (10.36) .017 (0.43) .027 (0.69) NOTES: 1. Dimensions are in
15、inches. 2. Metric equivalents are given for general information only. 3. Circuit diagrams are for information only. 4. All filters shall be supplied with mounting hardware. 5. Terminal identification. The case shall be marked at the threaded end of the filter, with the symbol “L” for dash numbers 00
16、01, 0003, 0004, 0006, and 0007. 6. Turret head is optional. 7. Flag terminals shall be aligned within 10 of the vertical (threaded bushing flats). FIGURE 1. Case dimensions and circuit diagrams - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS
17、-,-,-MIL-PRF-15733/49K 4 TABLE I. Electrical characteristics. * Rated voltage (volts) Minimum insertion loss (dB) in accordance with MIL-STD-220 at +25C 1/ Dash no. Circuit diagram Max rated current (amps) DC AC 6/ Max voltage drop (volts,dc) 30 kHz 150 kHz 300 kHz 1 MHz 10 MHz 100 MHz 1 GHz 5 GHz 1
18、0 GHz Cap -0 +100% (F) 8/ 0001 2/ L2 15 50 4/ - .15 8 20 28 38 55 70 70 70 70 0.68 0002 2/ Pi 3 150 7/ - .15 - 7 24 54 80 80 80 - 80 - 0003 2/ L2 10 50 7/ - .08 15 28 33 44 60 - 70 - - - 0004 2/ L2 10 50 3/ - .08 15 28 33 44 60 - 70 - - - 0005 2/ Pi 15 50 5/ - .09 70 dB from 420 MHz to 1.0 GHz, incl
19、usive - 0006 2/ L2 15 50 4/ - .15 15 28 33 44 60 - 70 - 70 1.2 0007 2/ L2 15 50 4/ - .15 15 28 33 44 60 - 70 - 70 1.2 0008 C 15 50 7/ - .06 - 33 40 50 65 - 70 - - 2.1 0010 C 15 330 7/ 125 .06 - 6 11 21 41 - 70 - - 0.062 8/ 1/ Insertion loss measurements shall be made under full load over the frequen
20、cy range of 150 kHz to 10 MHz. Insertion loss measurements above or below this frequency range shall be made under no load. 2/ Inactive for new design. 3/ Voltage rating at +125C (Note - derated from 80 V dc at +85) for dash number 0004. 4/ Voltage rating at +125C (Note- derated from 100 V dc at +85
21、C) for dash numbers 0001, 0006, and 0007. 5/ Voltage rating at +85C. 6/ AC voltage rating shall be dc to 400 Hz. 7/ Voltage rating at +125C. 8/ Capacitance tolerance on -0010 is -0, +150 percent. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PR
22、F-15733/49K 5 REQUIREMENTS: Dimensions and configuration: See figure 1. Weight: 8.5 grams, maximum. * Case: Metal, silver-plated finish for -0001; metal, tin-plated or electro-tin fused except the minimum lead content shall be 3 percent (pure tin finish is prohibited) or, tin-lead plated or hot-sold
23、er dipped (40 percent to 60 percent tin) for -0002 through -0008, and -0010. Pure tin is prohibited as specified in MIL-PRF-15733. Seal: Glass-to-metal. Terminals: Solderable (see figure 1). Dielectric: Ceramic. Operating temperature range: -55C to +125C, except -0005 shall be -55C to +85C. Rated vo
24、ltage: See table I. Rated current: See table I. Insertion loss (at 25C): In accordance with MIL-PRF-15733 and as specified in table I. (at -55C and 125C): Insertion loss shall be as specified in table I except a degradation of 4 dB shall be allowed up to 10 MHz. Voltage conditioning (applicable to -
25、0001, conformance inspection only): Prior to group A inspection, 100 percent of each lot of filters shall be subjected to voltage conditioning as follows: Test temperature: +125C +4C, -0C. Test voltage: 140 percent of the rated dc voltage. Points of application of test voltage: Between the case and
26、either terminal. Duration of exposure to test voltage: 250 hours, minimum. Measurements at +25C after the test: Dielectric withstanding voltage: 140 percent of rated dc voltage shall be applied for 1 minute. Insulation resistance: Shall be not less than 500 megohms. Insertion loss; Shall meet the in
27、itial requirements. A reject shall be defined as a filter that fails the dielectric withstanding voltage test, insulation resistance requirements, or insertion loss. If the total rejects from any particular lot exceed 10 percent, the entire lot shall be rejected. Provided by IHSNot for ResaleNo repr
28、oduction or networking permitted without license from IHS-,-,-MIL-PRF-15733/49K 6 Radiographic inspection (applicable to -0001, conformance inspection only): Following group A inspection, 100 percent of each lot of filters shall be subjected to radiographic inspection as follows: Filters shall be X-
29、rayed in one plane at 90-degree rotation (perpendicular to the filter longitudinal axis). Any evidence of poor capacitor mounting or uneven soldering of capacitor to case shall be cause for rejection. Rejected units shall be dissected and examined for poor workmanship or uneven soldering. Magnificat
30、ion during visual examination shall be two-power minimum. Any defects noted shall require corrective action prior to acceptance of any future lots. Seal: In accordance with MIL-PRF-15733. Capacitance to ground: In accordance with MIL-PRF-15733 and table I. Capacitance tolerance: +100 percent, -0 per
31、cent except -0010 shall be +150 percent, -0 percent. Temperature rise: +25C, maximum. Dielectric withstanding voltage: In accordance with MIL-PRF-15733 and the following: Test voltage: 125 percent of rated voltage (-0001); 370 V dc (-0002); 200 V dc (-0005); and 200 percent of rated voltage (-0003,
32、-0004, -0006, -0007, -0008, and -0010) applied between terminals and case for 1 minute; polarity of the test voltage shall then be reversed and the voltage shall be applied for 1 minute. Insulation resistance: In accordance with MIL-PRF-15733; the following details and exceptions shall apply: Test t
33、emperature: +25C. Test potential: Rated dc voltage or 100 V dc whichever is less. Insulation resistance shall be not less than: Dash numbers Megohms 0001 500 0002 through 0005, 0008 100 0006, 0007, and 0010 1,000 Dissipation factor (-0008 and -0010): 3 percent maximum. Voltage drop: See table I. Ove
34、rload: In accordance with MIL-PRF-15733. The following exception shall apply: Measurements after test: Insulation resistance (+25) only shall be measured and shall meet initial requirements. Terminal strength: In accordance with MIL-PRF-15733 and method 211, MIL-STD-202; test condition A (pull): App
35、lied force: 5 pounds (-0001 through -0007) 4.5 pounds +3, -0 ounces (-0008 and -0010). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15733/49K 7 Thermal shock and immersion: In accordance with MIL-PRF-15733 and the following: Measurements a
36、fter final cycling shall include: Capacitance change: Not more than 20 percent for dash numbers -0008 and -0010. Shock (specified pulse): In accordance with MIL-PRF-15733 and method 213 of MIL-STD-202, test condition I (-0001, -0002, -0003, -0004, -0006 through -0008, and -0010); and test condition
37、A (-0005). Vibration, high frequency: In accordance with MIL-PRF-15733 and method 204, MIL-STD-202. The following details and exceptions shall apply: Test condition: D (20 gs). Temperature conditioning (-0002 through -0005 only): Prior to vibration in each plane, filters shall be placed in an oven a
38、nd heated to +125C plus one-half the temperature rise (-0002 through -0004) and to +85C plus one-half the temperature rise (-0005). Vibration in each plane shall begin within 5 minutes after removal of the filters from the oven. Moisture resistance: In accordance with MIL-PRF-15733 and the following
39、: Polarization voltage: 50 volts dc. Measurements after 24-hour drying period shall be as specified in MIL-PRF-15733 and for 0008 and 0010 the capacitance shall change no more than 20 percent from initial measured value. Life: In accordance with MIL-PRF-15733 and method 108, MIL-STD-202. The followi
40、ng details shall apply: Test condition: For qualification inspection: D (1,000 hours). For group C inspection: B (250 hours) for -0001, -0003 through -0008, and -0010; D (1000 hours) for -0002. Marking: Filters shall be marked in accordance with MIL-PRF-15733. The following details shall apply: Mini
41、mum marking (-0001): Filters shall be marked with the PIN and terminal identification, as a minimum. The full marking specified in MIL-PRF-15733 shall be marked on the unit package. Full marking (-0002): Filters shall be marked with the full marking specified in MIL-PRF-15733. Minimum marking (-0003
42、 through -0008, and -0010): Filters shall be marked with the PIN, source code, date code, and terminal identification. The full marking specified in MIL-PRF-15733 shall be marked on the unit package. Part or Identifying Number (PIN): M15733/49-(dash number from table I). Provided by IHSNot for Resal
43、eNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15733/49K 8 Initial qualification to MIL-PRF-15733/49 may be granted based on qualification to MIL-PRF-28861/1 as indicated in table II. Extension of qualification from MIL-PRF-28861/1 is permissible under the following pr
44、ovisions: a. The MIL-PRF-15733/49 parts use the same design and dielectric characteristics as the comparable MIL-PRF-28861/1 parts. b. The MIL-PRF-28861/1 data verifies that the physical and electrical characteristics of the MIL-PRF-15733/49 parts are satisfied. TABLE II. Extension of qualification.
45、 Qualification to MIL-PRF-28861/1 Will qualify MIL-PRF-15733/49 Qualification to MIL-PRF-15733/49 Will qualify MIL-PRF-15733/49 -001 -0003 -0006 -0001 -001 -0004 -0006 -0007 -001 -0006 -0006 -0008 -001 -0007 -001 -0008 -002 -0008 Supersession data: See table III. * TABLE III. Supersession data. Inac
46、tive PIN For new design use PIN M83439/02-001 M15733/49-0008 M83439/02-003 M15733/49-0010 M15733/49-0001 M28861/01-001TB M15733/49-0002 M28861/03-015TB M15733/49-0003 M28861/01-001TB M15733/49-0004 M28861/01-001TB M15733/49-0005 M15733/38-0007 M15733/49-0006 M28861/01-001 M15733/49-0007 M28861/01-00
47、1TB PIN M15733/49-0009 has been deleted. For new design, use M28861/01-010 of MIL-PRF-28861/1. NOTES: Cataloging information: Dash numbers 0008 and 0010 shall be cataloged under FSC 5910 as feed-through ceramic capacitors. Dash numbers 0001 through 0007 shall be cataloged under FSC 5915 as radio fre
48、quency interference filters. * Referenced documents: In addition to MIL-PRF-15733, this specification sheet references the following documents: MIL-PRF-28861/1 MIL-STD-202 MIL-STD-220 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15733/49K 9 * Changes from previous issue: The margins of this specification sheet are marked with asterisks to indicate where changes from the previous iss
