1、 AMSC N/A FSC 5915 MIL-PRF-15733/61G SUPERSEDING 4 February 2011 MIL-PRF-15733/61F 2 September 2010 PERFORMANCE SPECIFICATION SHEET FILTERS, RADIO FREQUENCY INTERFERENCE, STYLES FL30, FL32, FL34, AND FL43 This specification sheet is approved for use by all Departments and Agencies of the Department
2、of Defense. The requirements for acquiring the filters described herein shall consist of this specification sheet and MIL-PRF-15733. FIGURE 1. Filter and hardware dimensions and circuit configurations. PART OR IDENTIFYING NUMBERS (PINs) M15733/61-0001 and 0004 ARE INACTIVE FOR NEW DESIGN AFTER 4 DEC
3、EMBER 1979. SEE TABLE V FOR NEW DESIGN DATA. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15733/61G 2 NOTES: 1. Circuit diagram is for information only. 2. Case is ground terminal. 3. Mounting hardware (lockwasher and hex nut) s
4、hall be supplied with each filter. 4. Terminal identification (nonsymmetrical filters): The case shall be marked at the threaded end of the filter, with the symbol “L” for L2circuits. 5. Hook bend radius: .046 (1.17 mm) (REF). 6. Turret head terminal is optional. 7. Potting shall not extend beyond .
5、030 inch (0.76 mm) from the filter body. 8. An undercut or imperfect threads out to a maximum of .060 inch (1.52 mm) from the hex head or mounting surface is permissible. FIGURE 1. Filter and hardware dimensions and circuit configurations - Continued. Provided by IHSNot for ResaleNo reproduction or
6、networking permitted without license from IHS-,-,-MIL-PRF-15733/61G 3 TABLE I. Filter dimensions. Type desig-nation 1/ Dash no. A B C D E Min Max Min Max Min Max Min Max Min Max FL30 0001 .203 (5.16) .233 (5.92) .172 (4.37) .202 (5.13) - .291 (7.39) .328 (8.33) .390 (9.91) .391 (9.93) .515 (13.08) F
7、L30 0002 .203 (5.16) .233 (5.92) .172 (4.37) .202 (5.13) - .291 (7.39) .328 (8.33) .390 (9.91) .391 (9.93) .515 (13.08) FL34 0003 .203 (5.16) .395 (10.03) .235 (5.97) .265 (6.73) .390 (9.91) .482 (12.24) .531 (13.49) .593 (15.06) .719 (18.26) .781 (19.84) FL34 0004 .203 (5.16) .395 (10.03) .235 (5.9
8、7) .265 (6.73) .390 (9.91) .482 (12.24) .531 (13.49) .593 (15.06) .719 (18.26) .781 (19.84) FL32 0006 .235 (5.97) .265 (6.73) .110 (2.79) .140 (3.56) .296 (7.52) .326 (8.28) .312 (7.92) .374 (9.50) .890 (22.61) .952 (24.18) FL32 0007 .240 (6.10) .260 (6.60) .115 (2.92) .135 (3.43) .296 (7.52) .326 (
9、8.28) .312 (7.92) .374 (9.50) .890 (22.61) .952 (24.18) FL32 0008 .206 (5.23) .226 (5.74) .083 (2.11) .103 (2.62) - .276 (7.01) .281 (7.14) .343 (8.71) .363 (9.22) .549 (13.94) FL32 0009 .240 (6.10) .260 (6.60) .271 (6.88) .291 (7.39) .396 (10.06) .416 (10.57) .44 (11.2) .50 (12.7) .65 (16.5) .71 (1
10、8.0) FL43 0011 .235 (5.97) .265 (6.73) .110 (2.79) .140 (3.56) .296 (7.52) .326 (8.28) .312 (7.92) .374 (9.50) .890 (22.61) .952 (24.18) FL43 0013 .201 (5.11) .231 (5.87) .078 (1.98) .108 (2.74) - .276 (7.01) - .312 (7.92) .859 (21.82) .921 (23.39) FL43 0014 .206 (5.23) .226 (5.74) .13 (3.3) .17 (4.
11、3) - .315 (8.00) .31 (7.9) - .49 (12.4) - FL43 0015 .203 (5.16) .233 (5.92) .172 (4.37) .202 (5.13) .266 (6.76) .296 (7.52) .328 (8.33) .390 (9.91) .422 (10.72) .484 (12.29) FL43 0016 .235 (5.97) .265 (6.73) .110 (2.79) .140 (3.56) .296 (7.52) .326 (8.28) .312 (7.92) .374 (9.50) .890 (22.61) .952 (2
12、4.18) See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15733/61G 4 TABLE I. Filter dimensions- Continued. Type desig-nation 1/ Dash no. F G J M N Weight (grams) (max) Min Max Min Max Min Max Thread 2/ FL30 0001 .
13、235 (5.97) .265 (6.73) - - - - .216-28 UNF-2A AWG 20 (.032) 2.6 FL30 0002 .235 (5.97) .265 (6.73) - - - - .216-32 UNEF-2A AWG 20 (.032) 2.2 FL34 0003 .360 (9.14) .390 (9.91) - - - - .3125-24 UNF-2A AWG 15 (.057) 7.1 FL34 0004 .360 (9.14) .390 (9.91) - - - - .3125-32 UNEF-2A AWG 15 (.057) 7.1 FL32 00
14、06 .177 (4.50) .197 (5.00) .220 (5.59) .250 (6.35) .017 (0.43) .047 (1.19) .216-32 UNEF-2A AWG 20 (.032) 2.0 FL32 0007 .177 (4.50) .197 (5.00) .235 (5.97) .265 (6.73) - .032 (0.81) .216-32 UNEF-2A AWG 20 (.032) 2.0 FL32 0008 .177 (4.50) .197 (5.00) - - - - .164-32 UNC-2A AWG 20 (.032) 2.0 FL32 0009
15、.177 (4.50) .197 (5.00) .240 (6.10) .260 (6.60) .115 (2.92) .135 (3.43) .216-32 UNEF-2A AWG 20 (.032) 3.2 FL43 0011 .172 (4.37) .202 (5.13) .220 (5.59) .250 (6.35) - .032 (0.81) .216-32 UNEF-2A AWG 20 (.032) 2.0 FL43 0013 .171 (4.34) .202 (5.13) - - - - .164-32 UNC-2A AWG 20 (.032) 2.2 FL43 0014 .17
16、7 (4.50) .197 (5.00) - - - - .164-32 UNC-2A AWG 20 (.032) 1.4 FL43 0015 .235 (5.97) .265 (6.73) - - - - .216-32 UNEF-2A AWG 18 (.040) 2.0 FL43 0016 .172 (4.37) .202 (5.13) - .235 (5.97) - .032 (0.81) .216-32 UNEF-2A AWG 20 (.032) 2.8 1/ The type designation does not describe a discrete item. For com
17、plete identification, the PIN should be referenced. 2/ The equivalent diameter in inches is shown in parentheses. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15733/61G 5 TABLE II. Hardware dimensions. Dash number Hex nut Lockwasher A B C
18、D E F Min Max Min Max Thread Min Max Min Max Min Max 0001 .235 (5.97) .265 (6.73) .070 (1.78) .080 (2.03) .216-28 UNF-2B .372 (9.45) .380 (9.65) .020 (0.51) .024 (0.61) .215 (5.46) .225 (5.72) 0002, 0006, 0007 0009, 0011 0015, 0016 .235 (5.97) .265 (6.73) .070 (1.78) .080 (2.03) .216-32 UNEF-2B .372
19、 (9.45) .380 (9.65) .020 (0.51) .024 (0.61) .215 (5.46) .225 (5.72) 0003 .365 (9.27) .385 (9.78) .085 (2.16) .100 (2.54) .3125-24 UNEF-2B .425 (10.80) .435 (11.05) .012 (0.30) .032 (0.81) .313 (7.95) .332 (8.43) 0004 .365 (9.27) .385 (9.78) .085 (2.16) .100 (2.54) .3125-32 UNEF-2B .425 (10.80) .435
20、(11.05) .012 (0.30) .032 (0.81) .313 (7.95) .332 (8.43) 0008, 0013 0014 .235 (5.97) .265 (6.73) .073 (1.85) .078 (1.98) .164-32 UNC-2B .324 (8.23) .336 (8.53) .015 (0.38) .025 (0.64) .162 (4.11) .172 (4.37) REQUIREMENTS: Design and construction: Dimensions and configuration: See figure 1, and table
21、I and II. Weight: See table I. Case and hardware: Silver plated. Terminals: Solderable. Leads shall be tin-lead coated copper wire. Mounting torque (by dash number): 0001, 0002, 0006, 0007, 0009, 0011, 0016 - 6 inch-pounds, maximum. 0003, 0004 - 8 inch pounds, maximum. 0008, 0013, 0014 - 3 inch poun
22、ds, maximum. Operating temperature range: -55C to +125C Rated voltage: See table III. Rated current: See table III. Insertion loss: In accordance with MIL-PRF-15733 at +25C and at temperature extremes (see table III). Provided by IHSNot for ResaleNo reproduction or networking permitted without licen
23、se from IHS-,-,-MIL-PRF-15733/61G 6 Voltage conditioning (conformance inspection only) (applicable to dash numbers 0002, 0003, and 0006 through 0016). The test shall be performed as follows: Test temperature: +125C +4C, -0C Test voltage: 1.4 times rated dc voltage. Test duration: 168 4 hours. Capaci
24、tance to ground: In accordance with MIL-PRF-15733 and table III. Temperature rise: 25C maximum except -0014 shall be 40C maximum. Dielectric withstanding voltage: In accordance with MIL-PRF-15733 except that the voltage shall be applied between either terminal and ground (case) for 1 to 5 seconds. B
25、arometric pressure (reduced): In accordance with MIL-PRF-15733 and method 105 of MIL-STD-202; test condition C. The following exception shall apply: Dielectric withstanding voltage: 1.5 times the rated dc voltage applied between either terminal and ground (case) for 1 to 5 seconds. Insulation resist
26、ance: In accordance with MIL-PRF-15733. The following details and exceptions shall apply: Test temperature: +25C 3C. Test potential: 100 V dc or rated dc voltage, whichever is less. Points of measurement: Between either terminal and ground (case). Minimum insulation resistance: 10,000 megohms. Volta
27、ge drop: In accordance with MIL-PRF-15733 and table III. Terminal strength: In accordance with MIL-PRF-15733 and method 211 of MIL-STD-202; test condition A. The following details shall apply: Applied force: 5 pounds. Overload: In accordance with MIL-PRF-15733. The following exception shall apply: M
28、easurements after test: Insulation resistance only shall be measured at +25C and shall meet initial requirements. Thermal shock and immersion: Not applicable. Shock (specified pulse): In accordance with MIL-PRF-15733 and method 213 of MIL-STD-202; test condition I. Vibration, high frequency: In acco
29、rdance with MIL-PRF-15733 and method 204 of MIL-STD-202; test condition D. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15733/61G 7 Radiographic inspection (conformance only) (applicable to dash numbers 0011and 0016 only). Filters shall be
30、 x-rayed in one plane at 90 degrees rotation perpendicular to their longitudinal axis. Any evidence of poor capacitor mounting or uneven soldering of capacitor to case shall be cause for rejection; rejected units shall be dissected and examined for poor workmanship or uneven soldering. Any defects n
31、oted shall require corrective action prior to acceptance of future lots. Magnification during visual inspection shall be 2 power, minimum. Unless otherwise specified, one radiograph shall be taken of each unit. Filters shall be positioned to yield a longitudinal image of the body. Moisture resistanc
32、e: Not applicable. Life: In accordance with MIL-PRF-15733 and method 108 of MIL-STD-202; test condition D. Part or Identifying Number (PIN): M15733/61-(dash number from table llI). Marking: Each filter shall be marked with the PIN. In addition, full marking in accordance with MIL-PRF-15733 shall be
33、marked on the unit package. TABLE III. Electrical characteristics. Dash number Cir-cuit Rated voltage Rated current amps Capac-itance (min) pF Volt-age drop volts Minimum insertion loss (dB) in accordance with MIL-STD-220. 1/ +25C V dc 2/ V rms 1 MHz 5 MHz 10 MHz 20 MHz 50 MHz 100 MHz 200 MHz 500 MH
34、z 1 GHz 10 GHz 0001 3/ 200 140 10 1,500 .1 - - - - 32 45 58 70 70 70 0002 200 140 10 1,500 .1 - - - - 32 45 58 70 70 70 0003 500 350 25 2,000 .5 - - - - 40 55 65 70 70 70 0004 3/ 500 350 25 2,000 .5 - - - - 40 55 65 70 70 70 0006 200 140 10 1,500 .1 - - - - 32 45 58 70 70 70 0007 100 70 10 5,000 .1
35、- - - - 50 65 70 70 70 70 0008 100 70 10 1,000 .1 - - - - 50 65 70 70 70 70 0009 70 - 10 12,000 .1 - 20 - 48 - 65 - - 65 65 0011 100 70 10 5,000 .5 - - - - 50 65 - 65 70 70 0013 L2 100 - 10 22,000 .1 10 - 30 - - 42 45 - 60 60 0014 50 - 20 10,000 .5 - - 20 - 50 65 70 - 70 70 0015 500 - 15 2,500 .15 -
36、 - 5 - - 50 55 - 70 70 0016 100 - 10 25,000 .1 - 15 - 60 60 65 - 65 65 65 1/ Insertion loss measurements between 1 MHz and 10 MHz, inclusive, shall be performed at full load. Insertion loss measurements above 10 MHz shall be performed at no load. 2/ Zero to 400 Hz over the rated temperature range of
37、 -55C to +125C. 3/ Inactive for new design. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15733/61G 8 TABLE III. Electrical characteristics- Continued. Dash number Cir-cuit Rated voltage Rated currentamps Capac- itance (min) pF Volt-age dro
38、p volts Minimum insertion loss (dB) in accordance with MIL-STD-220. 1/ -55C and +125C V dc Vrms 2/ 1 MHz 5 MHz 10 MHz 20 MHz 50 MHz 100 MHz 200 MHz 500 MHz 1 GHz 10 GHz 0001 3/ 200 140 10 1,500 .1 - - - - 15 28 46 70 70 70 0002 200 140 10 1,500 .1 - - - - 15 28 46 70 70 70 0003 500 350 25 2,000 .5 -
39、 - - - 25 40 59 70 70 70 0004 3/ 500 350 25 2,000 .5 - - - - 25 40 59 70 70 70 0006 200 140 10 1,500 .1 - - - - 16 30 48 70 70 70 0007 100 70 10 5,000 .1 - - - - 16 30 48 70 70 70 0008 100 70 10 1,000 .1 - - - - 20 35 55 70 70 70 0009 70 - 10 12,000 .1 - 8 - 30 - 63 - - 65 65 0011 100 70 10 5,000 .5
40、 - - - - 16 30 - 65 70 70 0013 L2 100 - 10 22,000 .1 8 - 28 - - 40 43 - 60 60 0014 50 - 20 10,000 .5 - - 18 - 48 63 70 70 70 70 0015 500 - 15 2,500 .15 - - 3 - - 45 50 - 70 70 0016 100 - 10 25,000 .1 - 13 - 27 58 70 - 65 65 65 1/ Insertion loss measurements between 1 MHz and 10 MHz, inclusive, shall
41、 be performed at full load. Insertion loss measurements above 10 MHz shall be performed at no load. 2/ Zero to 400 Hz over the rated temperature range of -55C to +125C. 3/ Inactive for new design. Conformance inspection: In accordance with MIL-PRF-15733 except as follows: Group A: In accordance with
42、 MIL-PRF-15733 for dash numbers 0001 and 0004. Group A inspection for all other dash numbers shall be in accordance with table IV. Lots having greater than 10 percent rejects shall be considered reject lots. Reject lots, at the option of the manufacturer, may be reworked and submitted to group A ins
43、pection of table IV. TABLE IV. Group A inspection. Test or inspection Sampling procedure Voltage conditioning 100% Dielectric withstanding voltage 100% Insulation resistance 100% Voltage drop 1/ 100% Insertion loss (check test) 100% Radiographic inspection 2/ 100% Visual and mechanical inspection Se
44、e MIL-PRF-15733, group A inspection 1/ DC voltage drop/dc resistance test for dc rated filters shall be performed on a sample basis in accordance with MIL-PRF-15733, group A inspection. 2/ Applicable to dash numbers 0011 and 0016 only. Provided by IHSNot for ResaleNo reproduction or networking permi
45、tted without license from IHS-,-,-MIL-PRF-15733/61G 9 New design data: See table V. TABLE V. New design data. Canceled PINs For new design use M15733/61- Inactive PINs For new design use M15733/61- M15733/35-0001 0002 M15733/61-0001 0002 M15733/35-0002 0002 M15733/61-0004 0003 M15733/36-0001 0003 M1
46、5733/43-0001 0002 M15733/36-0002 0003 M15733/43-0002 0008 M15733/52-0001 0006 M15733/28-0001 0008 M15733/52-0002 0006 M15733/28-0002 0008 M15733/52-0003 0007 M15733/28-0003 0014 M15733/52-0004 0008 M15733/28-0004 0013 M15733/52-0005 0009 M15733/47-0001 0011 M15733/47-0002 0011 M15733/47-0003 0012 M1
47、5733/47-0005 0013 M15733/47-0004 0014 M15733/61-0005 0006 M15733/61-0010 0011 M15733/61-0012 0016 Application note: These nonhermetically sealed filters may be susceptible to moisture intrusion when subjected to repeated thermal cycling. If these items are to be utilized in applications enduring harsh environments, the user should consider placing them within hermetic enclosures. Referenced documents
