1、AMSC N/A FSC 5910 INCH-POUND MIL-PRF-19978/11C 26 March 2009 SUPERSEDING MIL-PRF-19978/11B 6 September 2002 PERFORMANCE SPECIFICATION SHEET CAPACITORS, FIXED, PLASTIC (OR PAPER-PLASTIC) DIELECTRIC, AXIAL-WIRE THREADED-STUD RETAINER, TUBULAR (UNINSULATED) (HERMETICALLY SEALED IN METAL CASES), ESTABLI
2、SHED RELIABILITY, STYLE CQR13 This specification sheet is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-19978. Inches mm Inches mm Inches mm .001 0.03 .1
3、25 3.18 .437 11.10 .004 0.10 .172 4.37 .562 14.27 .005 0.13 .188 4.78 .670 17.02 .016 0.41 .250 6.35 .750 19.05 .031 0.79 .312 7.92 1.000 25.40 .032 0.81 .375 9.53 1.625 41.38 Case dimension D C .005 G .562 or less .250 5/16-24UNF-2A .670 .375 7/16-28UNEF-2A .750 and up .437 1/2-28UNEF-2A NOTES: 1.
4、Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Leads shall be of solder coated solid wire, .032 +.004, -.001 (No. 20 AWG). 4. Mounting nuts and lockwashers shall be supplied. FIGURE 1. Style CQR13 capacitors. Provided by IHSNot for ResaleNo reproduction or
5、 networking permitted without license from IHS-,-,-MIL-PRF-19978/11C 2 REQUIREMENTS: Design and construction: Dimensions and configuration: See figure 1 and table II. Case material: Nonmagnetic (screwneck and end seal may be of magnetic material). Terminals: Axial-wire lead (see figure 1). Circuit d
6、iagram: Rated voltage: See table II. Rated temperature: -65 to +125C. Capacitance (cap.) (nom): See table II. Capacitance tolerance: See table II. Dissipation factor (DF) (max): 1.0 percent. Failure rate level: In accordance with MIL-PRF-19978. Reliability: In accordance with MIL-PRF-19978. Burn-in:
7、 In accordance with MIL-PRF-19978. Radiographic inspection: In accordance with MIL-PRF-19978. Seal: Method 112 of MIL-STD-202, test condition letter A. Barometric pressure: In accordance with MIL-PRF-19978. Test points: Circuit diagram 1: Between terminals and case. Circuit diagram 3: Between ungrou
8、nded terminal and case. Insulation resistance (IR): Terminal to terminal: See table I. Terminal to case: Greater than 10,000 megohms. Vibration, high frequency: Method 204 of MIL-STD-202, test condition B, with the following exception: Direction and duration of motion: 4 hours in each of two mutuall
9、y perpendicular directions (total of 8 hours), one parallel and the other perpendicular to the cylindrical axis. Salt spray: In accordance with MIL-PRF-19978. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-19978/11C 3 Solderability: In acc
10、ordance with MIL-PRF-19978. Terminal strength: Method 211 of MIL-STD-202, test condition letter D. Stability at low and high temperatures: Low temperature: Test temperature: -65C +0C, -5C. Capacitance change (max): -10 percent. High temperature: Test temperature: +125C +5C, -0C. Capacitance change (
11、max): +10 percent. Life: Capacitance change (max): 5 percent of initial measured value. Resistance to soldering heat: In accordance with MIL-PRF-19978. TABLE I. Terminal-to-terminal insulation resistance. Capacitance rating Minimum insulation resistance Characteristic K At 25C 0 to 0.6 microfarad 25
12、,000 megohms Greater than 0.6 microfarad 15,000 megohm-microfarads 1/ At 125C 0 to 0.08 microfarad 250 megohms Greater than 0.08 microfarad 20 megohm-microfarads 1/ 1/ Product obtained by multiplying the capacitance in microfarads by the insulation resistance in megohms. Provided by IHSNot for Resal
13、eNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-19978/11C 4 TABLE II. STYLE CQR13 capacitors. Case dimensions 2/ Circuit 1 Circuit 3 Part or Identifying Number (PIN) 1/ DC voltage rating Capacitancerating Capacitancetolerance Failure rate levels L .031 D +.015, -.005 L
14、.031 D +.015,-.005 Volts F Inches Inches Inches Inches CQR13A-KC392-3- 200 .0039 G, J, K M, P, R, S .750 .400 .688 .400 CQR13A-KC472-3- 200 .0047 G, J, K M, P, R, S .750 .400 .688 .400 CQR13A-KC562-3- 200 .0056 G, J, K M, P, R, S .750 .400 .688 .400 CQR13A-KC682-3- 200 .0068 G, J, K M, P, R, S .750
15、.400 .688 .400 CQR13A-KC183-3- 200 .018 G, J, K M, P, R, S .875 .400 .812 .400 CQR13A-KC223-3- 200 .022 G, J, K M, P, R, S .875 .400 .812 .400 CQR13A-KC273-3- 200 .027 G, J, K M, P, R, S .875 .400 .812 .400 CQR13A-KC333-3- 200 .033 G, J, K M, P, R, S .875 .400 .812 .400 CQR13A-KC393-3- 200 .039 G, J
16、, K M, P, R, S .875 .400 .812 .400 CQR13A-KC473-3- 200 .047 G, J, K M, P, R, S .875 .400 .812 .400 CQR13A-KC563-3- 200 .056 G, J, K M, P, R, S .875 .400 .812 .400 CQR13A-KC683-3- 200 .068 G, J, K M, P, R, S .875 .400 .812 .400 CQR13A-KC823-3- 200 .082 G, J, K M, P, R, S 1.125 .400 1.062 .400 CQR13A-
17、KC104-3- 200 .10 G, J, K M, P, R, S 1.125 .400 1.062 .400 CQR13A-KC124-3- 200 .12 G, J, K M, P, R, S 1.375 .400 1.312 .400 CQR13A-KC154-3- 200 .15 G, J, K M, P, R, S 1.375 .400 1.312 .400 CQR13A-KC184-3- 200 .18 G, J, K M, P, R, S 1.125 .562 1.062 .562 CQR13A-KC224-3- 200 .22 G, J, K M, P, R, S 1.12
18、5 .562 1.062 .562 CQR13A-KC274-3- 200 .27 G, J, K M, P, R, S 1.375 .562 1.312 .562 CQR13A-KC334-3- 200 .33 G, J, K M, P, R, S 1.375 .562 1.312 .562 CQR13A-KC394-3- 200 .39 G, J, K M, P, R, S 1.625 .562 1.562 .562 CQR13A-KC474-3- 200 .47 G, J, K M, P, R, S 1.625 .562 1.562 .562 CQR13A-KC564-3- 200 .5
19、6 G, J, K M, P, R, S 1.625 .670 1.562 .670 CQR13A-KC684-3- 200 .68 G, J, K M, P, R, S 1.625 .670 1.562 .670 CQR13A-KC824-3- 200 .82 G, J, K M, P, R, S 2.125 .750 2.062 .750 CQR13A-KC105-3- 200 1.000 G, J, K M, P, R, S 2.125 .750 2.062 .750 CQR13A-KE272-3- 400 .0027 G, J, K M, P, R, S .750 .400 .688
20、.400 CQR13A-KE332-3- 400 .0033 G, J, K M, P, R, S .750 .400 .688 .400 CQR13A-KE123-3- 400 .012 G, J, K M, P, R, S .875 .400 .812 .400 CQR13A-KE153-3- 400 .015 G, J, K M, P, R, S .875 .400 .812 .400 CQR13A-KE273-3- 400 .027 G, J, K M, P, R, S .875 .400 .812 .400 CQR13A-KE333-3- 400 .033 G, J, K M, P,
21、 R, S .875 .400 .812 .400 CQR13A-KE393-3- 400 .039 G, J, K M, P, R, S 1.125 .400 1.062 .400 CQR13A-KE473-3- 400 .047 G, J, K M, P, R, S 1.125 .400 1.062 .400 CQR13A-KE563-3- 400 .056 G, J, K M, P, R, S 1.375 .400 1.312 .400 CQR13A-KE683-3- 400 .068 G, J, K M, P, R, S 1.375 .400 1.312 .400 CQR13A-KE8
22、23-3- 400 .082 G, J, K M, P, R, S 1.125 .562 1.062 .562 CQR13A-KE104-3- 400 .10 G, J, K M, P, R, S 1.125 .562 1.062 .562 CQR13A-KE124-3- 400 .12 G, J, K M, P, R, S 1.375 .562 1.312 .562 CQR13A-KE154-3- 400 .15 G, J, K M, P, R, S 1.375 .562 1.312 .562 CQR13A-KE184-3- 400 .18 G, J, K M, P, R, S 1.625
23、.562 1.562 .562 CQR13A-KE224-3- 400 .22 G, J, K M, P, R, S 1.625 .562 1.562 .562 CQR13A-KE274-3- 400 .27 G, J, K M, P, R, S 1.625 .670 1.562 .670 CQR13A-KE334-3- 400 .33 G, J, K M, P, R, S 1.625 .670 1.562 .670 CQR13A-KE394-3- 400 .39 G, J, K M, P, R, S 2.125 .750 2.062 .750 CQR13A-KE474-3- 400 .47
24、G, J, K M, P, R, S 2.125 .750 2.062 .750 CQR13A-KF102-3- 600 .0010 G, J, K M, P, R, S .750 .400 .688 .400 CQR13A-KF122-3- 600 .0012 G, J, K M, P, R, S .750 .400 .688 .400 CQR13A-KF152-3- 600 .0015 G, J, K M, P, R, S .750 .400 .688 .400 CQR13A-KF182-3- 600 .0018 G, J, K M, P, R, S .750 .400 .688 .400
25、 See footnote at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-19978/11C 5 TABLE II. STYLE CQR13 capacitors - Continued. Case dimensions 2/ Circuit 1 Circuit 3 Part or Identifying Number (PIN) 1/ DC voltage rating Capacitancer
26、ating Capacitancetolerance Failure rate levels L .031 D +.015, -.005 L .031 D +.015,-.005 Volts F Inches Inches Inches Inches CQR13A-KF222-3- 600 .0022 G, J, K M, P, R, S .750 .400 .688 .400 CQR13A-KF272-3- 600 .0027 G, J, K M, P, R, S .875 .400 .812 .400 CQR13A-KF332-3- 600 .0033 G, J, K M, P, R, S
27、 .875 .400 .812 .400 CQR13A-KF392-3- 600 .0039 G, J, K M, P, R, S .875 .400 .812 .400 CQR13A-KF472-3- 600 .0047 G, J, K M, P, R, S .875 .400 .812 .400 CQR13A-KF562-3- 600 .0056 G, J, K M, P, R, S .875 .400 .812 .400 CQR13A-KF682-3- 600 .0068 G, J, K M, P, R, S .875 .400 .812 .400 CQR13A-KF822-3- 600
28、 .0082 G, J, K M, P, R, S .875 .400 .812 .400 CQR13A-KF103-3- 600 .010 G, J, K M, P, R, S .875 .400 .812 .400 CQR13A-KF123-3- 600 .012 G, J, K M, P, R, S .875 .400 .812 .400 CQR13A-KF153-3- 600 .015 G, J, K M, P, R, S .875 .400 .812 .400 CQR13A-KF183-3- 600 .018 G, J, K M, P, R, S .875 .400 .812 .40
29、0 CQR13A-KF223-3- 600 .022 G, J, K M, P, R, S .875 .400 .812 .400 CQR13A-KF273-3- 600 .027 G, J, K M, P, R, S 1.125 .400 1.062 .400 CQR13A-KF333-3- 600 .033 G, J, K M, P, R, S 1.125 .400 1.062 .400 CQR13A-KF393-3- 600 .039 G, J, K M, P, R, S 1.375 .400 1.312 .400 CQR13A-KF473-3- 600 .047 G, J, K M,
30、P, R, S 1.375 .400 1.312 .400 CQR13A-KF563-3- 600 .056 G, J, K M, P, R, S 1.125 .562 1.062 .562 CQR13A-KF683-3- 600 .068 G, J, K M, P, R, S 1.125 .562 1.062 .562 CQR13A-KF823-3- 600 .082 G, J, K M, P, R, S 1.375 .562 1.312 .562 CQR13A-KF104-3- 600 .10 G, J, K M, P, R, S 1.375 .562 1.312 .562 CQR13A-
31、KF124-3- 600 .12 G, J, K M, P, R, S 1.625 .562 1.562 .562 CQR13A-KF154-3- 600 .15 G, J, K M, P, R, S 1.625 .562 1.562 .562 CQR13A-KF184-3- 600 .18 G, J, K M, P, R, S 1.625 .670 1.562 .670 CQR13A-KF224-3- 600 .22 G, J, K M, P, R, S 1.625 .670 1.562 .670 CQR13A-KF274-3- 600 .27 G, J, K M, P, R, S 2.12
32、5 .750 2.062 .750 CQR13A-KF334-3- 600 .33 G, J, K M, P, R, S 2.125 .750 2.062 .750 CQR13A-KF394-3- 600 .39 G, J, K M, P, R, S 2.375 .750 2.312 .750 CQR13A-KF474-3- 600 .47 G, J, K M, P, R, S 2.375 .750 2.312 .750 CQR13A-KG184-3- 1,000 .18 G, J, K M, P, R, S 2.125 .750 2.062 .750 CQR13A-KG224-3- 1,00
33、0 .22 G, J, K M, P, R, S 2.125 .750 2.062 .750 CQR13A-KG274-3- 1,000 .27 G, J, K M, P, R, S 2.125 1.0 2.062 1.000 CQR13A-KG334-3- 1,000 .33 G, J, K M, P, R, S 2.125 1.0 2.062 1.000 CQR13A-KG394-3- 1,000 .39 G, J, K M, P, R, S 2.375 1.0 2.312 1.000 CQR13A-KG474-3- 1,000 .47 G, J, K M, P, R, S 2.375 1
34、.0 2.312 1.000 1/ Complete part number shall include additional symbols to indicate circuit, capacitance tolerance, and failure rate level, as applicable. 2/ See table III for metric equivalents. TABLE III. Millimeter equivalents of inches. Inches mm Inches mm Inches mm 0.005 0.13 0.688 17.48 1.312
35、33.32 0.015 0.38 0.750 19.05 1.375 34.93 0.031 0.79 0.812 20.62 1.562 39.67 0.235 5.97 0.833 21.16 1.625 41.28 0.312 7.92 0.875 22.23 2.062 52.37 0.400 10.16 1.000 25.40 2.125 53.98 0.562 14.27 1.062 26.97 2.312 58.72 0.670 17.02 1.125 28.58 2.375 60.33 Provided by IHSNot for ResaleNo reproduction o
36、r networking permitted without license from IHS-,-,-MIL-PRF-19978/11C 6 Changes from previous issue: The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liabili
37、ty whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced documents: In addition to MIL-PRF-1997
38、8, this document also references MIL-STD-202. Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 85 (Project 5910-2009-009) DLA - CC Review activities: Navy - MC Air Force - 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
