1、AMSC N/A FSC 5930 INCH-POUND MIL-PRF-22885/18K 24 November 2010 SUPERSEDING MIL-PRF-22885/18J 13 January 2005 PERFORMANCE SPECIFICATION SHEET SWITCH, PUSH BUTTON, ILLUMINATED, DRIPPROOF SEAL, MOMENTARY AND ALTERNATE ACTION (DPDT/TWO CIRCUIT - 2 AMPERES) This specification sheet is approved for use b
2、y all Departments and Agencies of the Department of Defense. The requirements for acquiring the indicator lights described herein shall consist of this specification sheet and MIL-PRF-22885. FIGURE 1. Switch, housing (without pushbutton lens). SOLDER TERMINAL SEE FIG. 4 Provided by IHSNot for Resale
3、No reproduction or networking permitted without license from IHS-,-,-MIL-PRF-22885/18K 2 FIGURE 2. Panel cutout, circuit diagram and nonturn washer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-22885/18K 3 Inches mm Inches mm Inches mm .00
4、3 .08 .050 1.27 .375 9.53 .004 .10 .055 1.40 .42 10.7 .005 .13 .070 1.78 .446 11.33 .006 .15 .090 2.29 .447 11.35 .007 .18 .104 2.64 .468 11.89 .015 .38 .110 2.79 .470 11.94 .016 .41 .13 3.3 .615 15.62 .02 .5 .136 3.45 .650 16.51 .025 .64 .27 6.9 .719 18.26 .030 .76 .349 8.86 2.10 53.3 .048 1.22 .36
5、 9.2 NOTES: 1. Dimensions are in inches. 2. Unless otherwise specified, tolerance is .016 (.41 mm) for three place decimals and .03 (8 mm) for two place decimals. 3. Metric equivalents are given for general information only. 4. Alignment of lens index slot to mounting flat 90 2. Applicable to units
6、with snap-in lens. 5. One hole mounting is recommended when panel seal is utilized. 6. Terminals shall be permanently identified as shown. FIGURE 2. Panel cutout, circuit diagram and nonturn washer - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from
7、 IHS-,-,-MIL-PRF-22885/18K 4 Inches mm Inches mm .001 .03 .100 2.54 .010 .25 .200 5.08 .025 .64 .20 5.1 .030 .76 .400 10.16 .03 .8 .047 1.19 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerances are .010 (25 mm) fo
8、r three place decimals and .03 (.8mm) for two place decimals. FIGURE 3. Printed circuit terminal positions and identification. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-22885/18K 5 Double Pole 2-Circuit Inches mm Inches mm .001 .03 .100
9、 2.54 .010 .25 .200 5.08 .025 .64 .20 5.1 .030 .76 .400 10.16 .03 .8 .047 1.19 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerances are .010 (25 mm) for three place decimals and .03 (.8mm) for two place decimals.
10、FIGURE 4. Solder terminal positions and identification. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-22885/18K 6 REQUIREMENTS: Dimensions and configuration: See figures 1, 2, 3, and tables I and II. Enclosure design: 2 (dripproof). Operati
11、on: See tables I and II. Color and display type: See MIL-PRF-22885/99 as applicable. Temperature characteristic: 1 (-55C to +85C). Vibration grade: 2 (10 - 500 Hz). Weight: 1.11 ounces maximum (includes lens and lamp). Operating characteristics: Operating force: 2 1 pounds. Plunger travel: .160 inch
12、 maximum. Shock (specified pulse): Method I (75 gs) except 50 gs for switches with M22885/22-01 through -05 lens. No opening of closed contacts in excess of 5 milliseconds. No closing of open contacts in excess of 10 microseconds. Electrical ratings: See table III. Contact resistance after electrica
13、l endurance: 1.5 ohms maximum. Part number: M22885/18- (dash number from table I or II). Dash numbers from table II are inactive for new design. Complete switch shall consist of: a. Switch housing in accordance with figures 1, 2, and 3. b. Lens. (MIL-PRF-22885/99). c. Lamp (T-1-3/4 midget flange bas
14、e, incandescent type): Not included, order separately. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-22885/18K 7 TABLE I. Dash numbers for switch housings. Dash numbers Circuit characteristic Operation Pushbutton lens type Printed circuit t
15、erminals 1/ Solder terminals 1/ 149 01 DPDT Momentary Threaded 150 02 DPDT Alternate action Threaded 151 03 Two circuit Momentary Threaded 152 04 Two circuit Alternate action Threaded 153 05 DPDT Momentary Snap-in 154 06 DPDT Alternate action Snap-in 155 07 Two circuit Momentary Snap-in 156 08 Two c
16、ircuit Alternate action Snap-in 1/ These are switch housings that do not include pushbutton lens. Acquire pushbutton lens separately. See MIL-PRF-22885/99. TABLE II. Inactive for new design dash numbers. 1/ Dash numbers Lens M22885/ Circuit characteristic Operation Lens type Printed circuit terminal
17、s Solder terminals 157 2/ 09 2/ 22-01 (Yellow) DPDT Momentary Threaded 158 2/ 10 2/ 22-02 (White) DPDT Momentary Threaded 159 2/ 11 2/ 22-03 (Red) DPDT Momentary Threaded 160 2/ 12 2/ 22-04 (Green) DPDT Momentary Threaded 161 2/ 13 2/ 22-05 (Blue) DPDT Momentary Threaded 162 14 22-06 (Yellow) DPDT M
18、omentary Threaded 163 15 22-07 (White) DPDT Momentary Threaded 164 16 22-08 (Red) DPDT Momentary Threaded 165 17 22-09 (Green) DPDT Momentary Threaded 166 18 22-10 (Blue) DPDT Momentary Threaded 167 19 22-11 (Yellow) DPDT Momentary Threaded 168 20 22-12 (White) DPDT Momentary Threaded 169 21 22-13 (
19、Red) DPDT Momentary Threaded 170 22 22-14 (Green) DPDT Momentary Threaded 171 23 22-15 (Blue) DPDT Momentary Threaded 172 24 22-16 (Yellow) DPDT Momentary Threaded 173 25 22-17 (White) DPDT Momentary Threaded 174 26 22-18 (Red) DPDT Momentary Threaded 175 27 22-19 (Green) DPDT Momentary Threaded 176
20、 28 22-20 (Blue) DPDT Momentary Threaded 177 2/ 29 2/ 22-01 (Yellow) DPDT Alternate action Threaded 178 2/ 30 2/ 22-02 (White) DPDT Alternate action Threaded 179 2/ 31 2/ 22-03 (Red) DPDT Alternate action Threaded 180 2/ 32 2/ 22-04 (Green) DPDT Alternate action Threaded 181 2/ 33 2/ 22-05 (Blue) DP
21、DT Alternate action Threaded See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-22885/18K 8 TABLE II. Inactive for new design dash numbers - 1/ Continued. Dash numbers Lens M22885/ Circuit characteristic Operation
22、Lens type Printed circuit terminals Solder terminals 182 34 22-06 (Yellow) DPDT Alternate action Threaded 183 35 22-07 (White) DPDT Alternate action Threaded 184 36 22-08 (Red) DPDT Alternate action Threaded 185 37 22-09 (Green) DPDT Alternate action Threaded 186 38 22-10 (Blue) DPDT Alternate actio
23、n Threaded 187 39 22-11 (Yellow) DPDT Alternate action Threaded 188 40 22-12 (White) DPDT Alternate action Threaded 189 41 22-13 (Red) DPDT Alternate action Threaded 190 42 22-14 (Green) DPDT Alternate action Threaded 191 43 22-15 (Blue) DPDT Alternate action Threaded 192 44 22-16 (Yellow) DPDT Alte
24、rnate action Threaded 193 45 22-17 (White) DPDT Alternate action Threaded 194 46 22-18 (Red) DPDT Alternate action Threaded 195 47 22-19 (Green) DPDT Alternate action Threaded 196 48 22-20 (Blue) DPDT Alternate action Threaded 197 2/ 49 2/ 22-01 (Yellow) Two circuit Momentary Threaded 198 2/ 50 2/ 2
25、2-02 (White) Two circuit Momentary Threaded 199 2/ 51 2/ 22-03 (Red) Two circuit Momentary Threaded 200 2/ 52 2/ 22-04 (Green) Two circuit Momentary Threaded 201 2/ 53 2/ 22-05 (Blue) Two circuit Momentary Threaded 202 54 22-06 (Yellow) Two circuit Momentary Threaded 203 55 22-07 (White) Two circuit
26、 Momentary Threaded 204 56 22-08 (Red) Two circuit Momentary Threaded 205 57 22-09 (Green) Two circuit Momentary Threaded 206 58 22-10 (Blue) Two circuit Momentary Threaded 207 59 22-11 (Yellow) Two circuit Momentary Threaded 208 60 22-12 (White) Two circuit Momentary Threaded 209 61 22-13 (Red) Two
27、 circuit Momentary Threaded 210 62 22-14 (Green) Two circuit Momentary Threaded 211 63 22-15 (Blue) Two circuit Momentary Threaded 212 64 22-16 (Yellow) Two circuit Momentary Threaded 213 65 22-17 (White) Two circuit Momentary Threaded 214 66 22-18 (Red) Two circuit Momentary Threaded 215 67 22-19 (
28、Green) Two circuit Momentary Threaded 216 68 22-20 (Blue) Two circuit Momentary Threaded 217 2/ 69 2/ 22-01 (Yellow) Two circuit Alternate action Threaded 218 2/ 70 2/ 22-02 (White) Two circuit Alternate action Threaded 219 2/ 71 2/ 22-03 (Red) Two circuit Alternate action Threaded 220 2/ 72 2/ 22-0
29、4 (Green) Two circuit Alternate action Threaded 221 2/ 73 2/ 22-05 (Blue) Two circuit Alternate action Threaded 222 74 22-06 (Yellow) Two circuit Alternate action Threaded 223 75 22-07 (White) Two circuit Alternate action Threaded 224 76 22-08 (Red) Two circuit Alternate action Threaded 225 77 22-09
30、 (Green) Two circuit Alternate action Threaded 226 78 22-10 (Blue) Two circuit Alternate action Threaded See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-22885/18K 9 TABLE II. Inactive for new design dash numbers
31、 - 1/ Continued. Dash numbers Lens M22885/ Circuit characteristic Operation Lens type Printed circuit terminals Solder terminals 227 79 22-11 (Yellow) Two circuit Alternate action Threaded 228 80 22-12 (White) Two circuit Alternate action Threaded 229 81 22-13 (Red) Two circuit Alternate action Thre
32、aded 230 82 22-14 (Green) Two circuit Alternate action Threaded 231 83 22-15 (Blue) Two circuit Alternate action Threaded 232 84 22-16 (Yellow) Two circuit Alternate action Threaded 233 85 22-17 (White) Two circuit Alternate action Threaded 234 86 22-18 (Red) Two circuit Alternate action Threaded 23
33、5 87 22-19 (Green) Two circuit Alternate action Threaded 236 88 22-20 (Blue) Two circuit Alternate action Threaded 237 89 19-01 (Yellow) DPDT Momentary Snap-in 238 90 19-02 (White) DPDT Momentary Snap-in 239 91 19-03 (Red) DPDT Momentary Snap-in 240 92 19-04 (Green) DPDT Momentary Snap-in 241 93 19-
34、05 (Blue) DPDT Momentary Snap-in 242 94 19-06 (Yellow) DPDT Momentary Snap-in 243 95 19-07 (White) DPDT Momentary Snap-in 244 96 19-08 (Red) DPDT Momentary Snap-in 245 97 19-09 (Green) DPDT Momentary Snap-in 246 98 19-10 (Blue) DPDT Momentary Snap-in 247 99 19-11 (Yellow) DPDT Momentary Snap-in 248
35、100 19-12 (White) DPDT Momentary Snap-in 249 101 19-13 (Red) DPDT Momentary Snap-in 250 102 19-14 (Green) DPDT Momentary Snap-in 251 103 19-15 (Blue) DPDT Momentary Snap-in 252 104 19-01 (Yellow) DPDT Alternate action Snap-in 253 105 19-02 (White) DPDT Alternate action Snap-in 254 106 19-03 (Red) DP
36、DT Alternate action Snap-in 255 107 19-04 (Green) DPDT Alternate action Snap-in 256 108 19-05 (Blue) DPDT Alternate action Snap-in 257 109 19-06 (Yellow) DPDT Alternate action Snap-in 258 110 19-07 (White) DPDT Alternate action Snap-in 259 111 19-08 (Red) DPDT Alternate action Snap-in 260 112 19-09
37、(Green) DPDT Alternate action Snap-in 261 113 19-10 (Blue) DPDT Alternate action Snap-in 262 114 19-11 (Yellow) DPDT Alternate action Snap-in 263 115 19-12 (White) DPDT Alternate action Snap-in 264 116 19-13 (Red) DPDT Alternate action Snap-in 265 117 19-14 (Green) DPDT Alternate action Snap-in 266
38、118 19-15 (Blue) DPDT Alternate action Snap-in 267 119 19-01 (Yellow) Two circuit Momentary Snap-in 268 120 19-02 (White) Two circuit Momentary Snap-in 269 121 19-03 (Red) Two circuit Momentary Snap-in 270 122 19-04 (Green) Two circuit Momentary Snap-in 271 123 19-05 (Blue) Two circuit Momentary Sna
39、p-in See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-22885/18K 10 TABLE II. Inactive for new design dash numbers - 1/ Continued. Dash numbers Lens M22885/ Circuit characteristic Operation Lens type Printed circu
40、it terminals Solder terminals 272 124 19-06 (Yellow) Two circuit Momentary Snap-in 273 125 19-07 (White) Two circuit Momentary Snap-in 274 126 19-08 (Red) Two circuit Momentary Snap-in 275 127 19-09 (Green) Two circuit Momentary Snap-in 276 128 19-10 (Blue) Two circuit Momentary Snap-in 277 129 19-1
41、1 (Yellow) Two circuit Momentary Snap-in 278 130 19-12 (White) Two circuit Momentary Snap-in 279 131 19-13 (Red) Two circuit Momentary Snap-in 280 132 19-14 (Green) Two circuit Momentary Snap-in 281 133 19-15 (Blue) Two circuit Momentary Snap-in 282 134 19-01 (Yellow) Two circuit Alternate action Sn
42、ap-in 283 135 19-02 (White) Two circuit Alternate action Snap-in 284 136 19-03 (Red) Two circuit Alternate action Snap-in 285 137 19-04 (Green) Two circuit Alternate action Snap-in 286 138 19-05 (Blue) Two circuit Alternate action Snap-in 287 139 19-06 (Yellow) Two circuit Alternate action Snap-in 2
43、88 140 19-07 (White) Two circuit Alternate action Snap-in 289 141 19-08 (Red) Two circuit Alternate action Snap-in 290 142 19-09 (Green) Two circuit Alternate action Snap-in 291 143 19-10 (Blue) Two circuit Alternate action Snap-in 292 144 19-11 (Yellow) Two circuit Alternate action Snap-in 293 145
44、19-12 (White) Two circuit Alternate action Snap-in 294 146 19-13 (Red) Two circuit Alternate action Snap-in 295 147 19-14 (Green) Two circuit Alternate action Snap-in 296 148 19-15 (Blue) Two circuit Alternate action Snap-in 1/ These switch assemblies include MIL-S-22885/19 or MIL-S-22885/22 pushbut
45、ton lens which have been cancelled. Replace with separate switch housing (see table I) and pushbutton lens (see MIL-PRF-22885/99) 2/ Switches with lenses M22885/22-01 through M22885/22-05 are not for applications that require greater than 50 g shock loads. TABLE III. Electrical ratings. Load 28 V dc
46、 115 V ac (60/400 Hz) amperes amperes Resistive 2.0 2.0 Inductive 1.5 1.5 Lamp 0.5 0.5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-22885/18K 11 QUALIFICATION: Qualification inspection: All applicants for qualification approval shall demon
47、strate that each of their items conforms to all the requirements specified in the applicable documents, singularly and in combination with all other previously qualified items, regardless of manufacturer (see table IV). Group A inspection. Seal test. Visual examination only. TABLE IV. Qualification
48、inspection (group submission). Sample units Qualification table of MIL-PRF-22885 Extent of approval Assembly of M22885/18-02 and M22885/99-K108 1/ All tests 2/ All Assembly of M22885/18-153 and M22885/99-K208 Groups I and II Assembly of M22885/18-07and M22885/99-K208 (2 sample units) Visual and mechanical examination Operating characteristics Contact resistance Assembly of M22885/18-08 and M22885/99-K208 (2 sample units) 1/ For group VIII tests, two samples each of M22885/99-K201 through M22885/99-K215 pushbutton lens shall be assembled to M2
