DLA MIL-PRF-27 315 C-2008 TRANSFORMERS POWER 20 VOLT-AMPERES 60 HERTZ《电源变压器20VA 60Hz》.pdf

上传人:syndromehi216 文档编号:692703 上传时间:2018-12-30 格式:PDF 页数:4 大小:94.64KB
下载 相关 举报
DLA MIL-PRF-27 315 C-2008 TRANSFORMERS POWER 20 VOLT-AMPERES 60 HERTZ《电源变压器20VA 60Hz》.pdf_第1页
第1页 / 共4页
DLA MIL-PRF-27 315 C-2008 TRANSFORMERS POWER 20 VOLT-AMPERES 60 HERTZ《电源变压器20VA 60Hz》.pdf_第2页
第2页 / 共4页
DLA MIL-PRF-27 315 C-2008 TRANSFORMERS POWER 20 VOLT-AMPERES 60 HERTZ《电源变压器20VA 60Hz》.pdf_第3页
第3页 / 共4页
DLA MIL-PRF-27 315 C-2008 TRANSFORMERS POWER 20 VOLT-AMPERES 60 HERTZ《电源变压器20VA 60Hz》.pdf_第4页
第4页 / 共4页
亲,该文档总共4页,全部预览完了,如果喜欢就下载吧!
资源描述

1、AMSC N/A FSC 5950 INCH-POUND MIL-PRF-27/315C 25 July 2008 SUPERSEDING MIL-PRF-27/315B 19 May 2003 PERFORMANCE SPECIFICATION SHEET TRANSFORMERS, POWER, 20 VOLT-AMPERES, 60 HERTZ This specification is approved for use by all Depart- ments and Agencies of the Department of Defense. The complete require

2、ments for acquiring the transformer described herein shall consist of this specification and the latest issue of MIL-PRF-27. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Marking shall be on the sides of the case. 4. Unless otherwise specified t

3、he tolerance shall be .063 inch (1.60 mm). 5. Electrical values shall be marked as specified in table I, except DCR. FIGURE 1. Dimensions and configurations. INCHES MM .005 .016 .031 .062 .070 .375 .875 1.50 1.75 2.00 2.38 3.13 0.13 0.41 0.79 1.57 1.78 9.53 22.23 38.1 44.5 50.8 60.5 79.5 Provided by

4、 IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-27/315C 2 REQUIREMENTS: (When numbers in parentheses, i.e., (1-2) are used, they indicate the winding and the extreme terminals of the winding.) Electrical ratings: Primary voltage (1-2): 115 volts ac, 50

5、to 60 hertz. Primary dc resistance: 15 ohms 25 percent. Secondary voltage (3-5): See table I. Volt-ampere rating: 20 volt-amperes. Working voltage (1-2): 535 volts peak. Design and construction: Dimensions and configuration: See figure 1. Duty cycle: Continuous. Case: Metal enclosed. Material: Steel

6、 Terminals: Solderable hook terminals. Terminal height: 0.375 0.063 inch. Terminal diameter: 0.062 0.005 inch. Weight: 2.5 pounds, maximum. Operating temperature range: -55C to +130C. Altitude: 10,000 feet. Terminal strength: MIL-STD-202, method 211, test condition A, 2.0 pounds. Dielectric withsta

7、nding voltage (each winding) (at sea level): 1,500 volts rms. Electrical characteristics: Rated load: With 115 volts ac and 60 Hz across (1-2), and rated current in secondary, the voltage across (3-5) shall be as specified in table I. Regulation: Voltage (no load) - Voltage (rated load) x 100 Voltag

8、e (rated load) Shall not exceed 10 percent. Polarity: Additive with terminals 2 and 3 connected. Temperature rise: 35C with 115 volts ac, 60 hertz across (1-2) at an ambient temperature of 95C, full load terminals (3-5). Provided by IHSNot for ResaleNo reproduction or networking permitted without li

9、cense from IHS-,-,-MIL-PRF-27/315C 3 Marking location: See figure 1. Part or Identification Number (PIN): M27/315-(dash number from table I). TABLE I. Electrical ratings. Secondary (3-5) Dash number Voltage (volts) 3 percent Current 1/ (amperes) DC resistance (ohms) 25 percent 01 02 03 04 05 06 07 0

10、8 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 5.0 6.3 8.0 10.0 12.6 14.0 16.0 18.0 20.0 22.0 25.0 28.0 31.0 35.0 39.0 43.0 48.0 55.0 63.0 70.0 80.0 90.0 100 110 123 138 157 175 200 220 4.00 3.16 2.50 2.00 1.59 1.43 1.25 1.11 1.00 0.91 0.80 0.71 0.64 0.57 0.51 0.46 0.42 0.36 0.3

11、2 0.286 0.250 0.222 0.200 0.182 0.162 0.145 0.127 0.114 0.100 0.091 0.066 0.100 0.150 0.230 0.340 0.40 0.52 0.62 0.85 0.95 1.37 1.60 2.20 2.40 3.6 4.0 4.4 6.0 8.6 9.8 13.4 14.8 15.5 23.0 35.0 37.5 48.2 55.0 75.0 95.0 1/ For 50 Hz operation, reduce secondary current by 10 percent. VERIFICATION: Exten

12、t of Qualification: Qualification testing and approval to M27/312-26 or M27/316-30 or M27/322-24 shall be sufficient to grant qualification approval to MIL-PRF-27/322, inclusive, all parts. Qualification testing and approval to M27/315-30 shall be sufficient to grant qualification approval M27/315-0

13、1 through M27/315-30. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-27/315C 4 Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This wa

14、s done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last

15、 previous issue. Referenced documents. MIL-PRF-27 MIL-STD-202 Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 85 (Project 5950-2008-042) DLA - CC Review activities: Army - CR4, MI Navy - AS, MC, OS Air Force - 19, 99 NOTE: The activities listed above were interested in this

16、document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

展开阅读全文
相关资源
猜你喜欢
  • DIN EN ISO 2495-2000 Iron blue pigments - Specifications and methods of test (ISO 2495 1995) German version EN ISO 2495 2000《铁蓝颜料 规范和试验方法》.pdf DIN EN ISO 2495-2000 Iron blue pigments - Specifications and methods of test (ISO 2495 1995) German version EN ISO 2495 2000《铁蓝颜料 规范和试验方法》.pdf
  • DIN EN ISO 2503-2015 Gas welding equipment - Pressure regulators and pressure regulators with flow-metering devices for gas cylinders used in welding cutting and allied processes u5.pdf DIN EN ISO 2503-2015 Gas welding equipment - Pressure regulators and pressure regulators with flow-metering devices for gas cylinders used in welding cutting and allied processes u5.pdf
  • DIN EN ISO 2505-2005 Thermoplastics pipes - Longitudinal reversion - Test methods and parameters (ISO 2505 2005) German version EN ISO 2505 2005《热塑性管 纵向回缩 试验方法和参数》.pdf DIN EN ISO 2505-2005 Thermoplastics pipes - Longitudinal reversion - Test methods and parameters (ISO 2505 2005) German version EN ISO 2505 2005《热塑性管 纵向回缩 试验方法和参数》.pdf
  • DIN EN ISO 252-2008 Conveyor belts - Adhesion between constitutive elements - Test methods (ISO 252 2007) English version of DIN EN ISO 252 2008-01《输送带 结构组件间的附着力 试验方法(ISO 252 2007).pdf DIN EN ISO 252-2008 Conveyor belts - Adhesion between constitutive elements - Test methods (ISO 252 2007) English version of DIN EN ISO 252 2008-01《输送带 结构组件间的附着力 试验方法(ISO 252 2007).pdf
  • DIN EN ISO 2535-2003 Plastics - Unsaturated polyester resins - Measurement of gel time at ambient temperature (ISO 2535 2001) German version EN ISO 2535 2002《塑料 不饱和聚酯树脂 室温胶凝时间测量》.pdf DIN EN ISO 2535-2003 Plastics - Unsaturated polyester resins - Measurement of gel time at ambient temperature (ISO 2535 2001) German version EN ISO 2535 2002《塑料 不饱和聚酯树脂 室温胶凝时间测量》.pdf
  • DIN EN ISO 2538-1-2015 Geometrical product specfications (GPS) - Wedges - Part 1 Series of angles and slopes (ISO 2538-1 2014) German version EN ISO 2538-1 2014《几何产品技术规格 (GPS) 棱体 第.pdf DIN EN ISO 2538-1-2015 Geometrical product specfications (GPS) - Wedges - Part 1 Series of angles and slopes (ISO 2538-1 2014) German version EN ISO 2538-1 2014《几何产品技术规格 (GPS) 棱体 第.pdf
  • DIN EN ISO 2538-2-2015 Geometrical product specifications (GPS) - Wedges - Part 2 Dimensioning and tolerancing (ISO 2538-2 2014) German version EN ISO 2538-2 2014《几何产品技术规格 (GPS) 棱体.pdf DIN EN ISO 2538-2-2015 Geometrical product specifications (GPS) - Wedges - Part 2 Dimensioning and tolerancing (ISO 2538-2 2014) German version EN ISO 2538-2 2014《几何产品技术规格 (GPS) 棱体.pdf
  • DIN EN ISO 2553-2014 Welding and allied processes - Symbolic representation on drawings - Welded joints (ISO 2553 2013) German version EN ISO 2553 2013《焊接及相关工艺 图纸上的符号表示 焊接接头(ISO 25.pdf DIN EN ISO 2553-2014 Welding and allied processes - Symbolic representation on drawings - Welded joints (ISO 2553 2013) German version EN ISO 2553 2013《焊接及相关工艺 图纸上的符号表示 焊接接头(ISO 25.pdf
  • DIN EN ISO 2554-1998 Plastics - Unsaturated polyester resins - Determination of hydroxyl value (ISO 2554 1997) German version EN ISO 2554 1998《塑料 不饱和聚酯树脂 羟基值的测定》.pdf DIN EN ISO 2554-1998 Plastics - Unsaturated polyester resins - Determination of hydroxyl value (ISO 2554 1997) German version EN ISO 2554 1998《塑料 不饱和聚酯树脂 羟基值的测定》.pdf
  • 相关搜索

    当前位置:首页 > 标准规范 > 国际标准 > 其他

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1