1、 AMSC N/A FSC 5945 MIL-PRF-6106/13F 17 November 2011 SUPERSEDING MIL-PRF-6106/13E 10 November 2000 PERFORMANCE SPECIFICATION RELAY, ELECTROMAGNETIC, 25 AMPERE, 3PST, NO, WITH 2 AMPERE 1PDT AUXILIARY CONTACTS, HERMETICALLY SEALED, PERMANENT MAGNET DRIVE, TYPE I This specification is approved for use
2、by all Departments and Agencies of the Department of Defense. The requirements for acquiring the relays described herein shall consist of this specification sheet and MIL-PRF-6106. RAISED VERTICAL FLANGE MOUNT I AND TERMINAL LAYOUT FOR -001, -002, -003, -005, -007, -008, -016 AND -017 FIGURE 1. Rela
3、y, outline drawing. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-6106/13F 2 Inches mm Inches mm Inches Mm .000 0.00 .150 3.81 .625 15.88 .001 0.03 .156 3.96 .630 16.00.002 0.05 .234 5.94 .937 23.80 .003 0.08 .300 7.62 1.010 25.6
4、5.020 0.51 .312 7.92 1.025 26.04 .040 1.02 .395 10.03 1.396 35.46.062 1.57 .432 10.97 1.446 36.73 .093 2.36 .450 11.43 1.718 43.64.117 2.97 .600 15.24 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerance is .010 (0
5、.25 mm). FIGURE 1. Relay, outline drawing - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-6106/13F 3 RAISED VERTICAL FLANGE MOUNT 2 AND TERMINAL LAYOUT FOR -004 Inches mm Inches mm Inches mm .000 0.00 .150 3.81 .600 15.24 .001 0.
6、03 .156 3.96 .625 15.88 .002 0.05 .234 5.94 .630 16.00 .020 0.51 .300 7.62 .937 23.80 .040 1.02 .312 7.92 1.010 25.65 .062 1.57 .395 10.03 1.025 26.04 .093 2.36 .432 10.97 1.396 35.46 .117 2.97 .450 11.43 1.446 36.73 1.718 43.64NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for
7、general information only. 3. Unless otherwise specified, tolerance is .010 (.25 mm). FIGURE 2. Relay, outline drawing. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-6106/13F 4 HORIZONTAL FLANGE MOUNT 3 AND TERMINAL LAYOUT FOR 006, -009 AND
8、018. Inches mm Inches mm Inches mm .001 0.03 .150 3.81 .625 15.88 .002 0.05 .234 5.94 .630 16.00 .003 0.08 .300 7.62 .937 23.80 .040 1.02 .312 7.92 1.010 25.65 .062 1.57 .432 10.97 1.025 26.04 .093 2.36 .450 11.43 1.396 35.46 .117 2.97 .600 15.24 1.446 36.73 1.718 43.64NOTES: 1. Dimensions are in in
9、ches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerance is .010 (.25 mm). FIGURE 3. Relay, outline drawing. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-6106/13F 5 NO MOUNT 4 AND TERMINA
10、L LAYOUT FOR -010, -011, -012, -013, -014, AND -015. Inches mm Inches mm .001 0.03 .234 5.94 .002 0.05 .300 7.62 .003 0.08 .432 10.97 .062 1.57 .450 11.43 .093 2.36 .600 15.24 .117 2.97 .630 16.00 .150 3.81 1.010 25.65 1.025 26.04NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given fo
11、r general information only. 3. Unless otherwise specified, tolerance is .010 (.25 mm). FIGURE 4. Relay, outline drawing. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-6106/13F 6 SOLDER PIN TERMINALS Inches mm Inches mm Inches mm .000 0.00 .
12、020 0.51 .250 6.35 .001 0.03 .040 1.02 .270 6.86 .002 0.05 .050 1.27 .300 7.62 .003 0.08 .062 1.57 .375 9.52 .005 0.13 .093 2.36 .625 15.88 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerance is .010 (0.25 mm). 4.
13、 Hook terminals will accept (1) one number 12 AWG stranded wire. 5. Socket pin terminals shall provide the operational, environmental, and interface characteristics to provide a reliable interconnect to gold-plated contacts. Terminals shall be gold plated, except the polarizing pin. One system for g
14、old plating that may be used is ASTM B488, type 3, class 1.25 with a nickel underplate of 50 to 150 microinches thick. The gold plating system shall enable the product to meet the performance requirements of this specification and shall be approved by the qualifying activity. 6. Gasket shall provide
15、 a reliable seal between the relay and mating socket that will meet the environmental, operational, and interface requirements of the relay with the mating socket. The gasket shall have shore hardness 20 5, thickness .050 .005. Gasket material according to SAE-AMS3332 has been considered acceptable.
16、 FIGURE 5. Relay, termination styles. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-6106/13F 7 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerance is .01
17、0 (.25 mm). FIGURE 6. Relay, mounting hole layouts. Inches mm Inches mm .001 0.03 .218 5.54 .005 0.13 .312 7.92 .062 1.57 .625 15.88 .156 3.96 1.062 26.97 .172 4.37 1.406 35.71 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-6106/13F 8 NOTES:
18、 1. There shall be affixed to the relay a suitable legible circuit diagram that identifies each terminal location specified. 2. DC versions of this relay must not operate or be damaged by reverse polarity, semiconductors shall not be used for this purpose. 3. Coil polarity not applicable to AC versi
19、ons -003, -004, -012, and -013. 4. When semiconductors are required, JANTX or equivalent screened semiconductors shall be used. Relays using suppression devices shall continue to operate should the suppression circuit be in a failure mode. Diodes shall have a peak inverse voltage of 600 V dc minimum
20、. FIGURE 7. Relay, circuit diagrams. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-6106/13F 9 REQUIREMENTS Coil data: Coil data: See table I. Duty rating: Continuous. Operational data: Rated contact load: See table II. Operate time: See tab
21、le I. Release time: See table I. Physical: Dimensions and configuration: See figure 1 through 6. Weight (maximum): 0.18 pound, 81.64 grams. Thermal type: See figure 5 and table I. Strength of terminals and mounting studs: Applicable. Terminal solderability: Applicable to solder pin and solder hook t
22、erminals only. ENVIRONMENTAL CHARACTERISTICS: Temperature range: -70C to +125C. 1/ Maximum altitude: 300,000 feet. Shock g-level: 200 g, 100 g for -006, -009, and -018 only. 2/ Duration: 6 ms. Maximum duration contact opening: Deleted. Vibration-sinusoidal: 2/ G level: 30 g, 20 g for -006, -009, and
23、 -018 only. Frequency range: 10 to 3,000 Hz. Vibration (random): 2/ Applicable standard: MIL-STD-202, method 214. Test condition: IG, IE for -006, -009, and -018 only. _ 1/ For full rated load, maximum temperature, and altitude use no. 12 wire or larger. Solder hook relays are to be mounted to limit
24、 mounting bracket temperature to 160C for dc units and 135C for ac units. 2/ There shall be no opening of closed auxiliary contacts in excess of 1 ms, no closure or bridging of open auxiliary contacts in excess of 100 s.Provided by IHSNot for ResaleNo reproduction or networking permitted without lic
25、ense from IHS-,-,-MIL-PRF-6106/13F 10 Power spectral density: 0.4 G2/Hz, 50 to 2,000 Hz (0.2 G2/Hz) for -006, -009, and -018 only. Duration: 15 minutes, each plane. Acceleration: 15 gs. 2/ ELECTRICAL CHARACTERISTICS: Insulation resistance, initial: 100 megohms. After life or environmental tests: 50
26、megohms. Dielectric withstanding voltage (seal level): 2 to 5 seconds. Initial After life tests Coil to case 1,000 V rms 1,000 V rms Auxiliary contacts 1,000 V rms 750 V rms All other points 1,250 V rms 1,000 V rms Dielectric withstanding voltage (altitude): 1 minute. 3/ 80,000 feet 300,000 feet Coi
27、l to case 350 V rms 500 V rms Auxiliary contacts 350 V rms 500 V rms All other points 350 V rms 500 V rms Maximum contact drop, initial: 0.150 volt. After life test: 0.175 volt. Overload current: 50 amperes dc, 80 amperes ac. Rupture current: 60 amperes dc, 100 amperes ac. RFI specification (applica
28、ble to coil circuits of ac operated relays): MIL-STD-461. Part Number: M6106/13-(dash number from table I). Qualification by similarity: See MIL-PRF-6106. _ 3/ Dielectric rating may be improved by suitable insulation of terminals and wiring after installation. Provided by IHSNot for ResaleNo reprodu
29、ction or networking permitted without license from IHS-,-,-TABLE I. Mounting, termination, and operating characteristics. Dash No. Coil term-inal Coil data Time (milliseconds) (max) Terminals Mount figure Nominal Maximum Max pickup voltage Drop out voltage Hold voltage Operate2/ Release 3/ Bounce Vo
30、lts Freq Hz Res Volts Amp Normal 1/ High temp test Cont. curr test Main Aux NO NC NO NC -001 Solder-hook 1 -002 Socket plug-in 1 -005 4/ Solder pin 1 -006 4/ DC 28 DC - 29 .12 18 19.8 22.5 1.5 7.0 15 15 1.0 - 4 4 Solder pin 3 -009 Solder-hook 3 -010 Solder pin 4 -011 Socket plug-in 4 -003 Solder-hoo
31、k 1 -004 AC 115 400 - 122 .04 90 95 103 5 30 20 50 1.0 - 4 4 Socket plug-in 2 -012 Solder pin 4 -013 Socket-plug-in 4 -007 5/ Solder-hook 1 -008 5/ DC 28 DC - 29 .12 18 19.8 22.5 1.5 7.0 15 15 1.0 - 4 4 Socket plug-in 1 -014 5/ Solder pin 4 -015 5/ Socket plug-in 4 -016 5/ Solder pin 1 -017 4/ 5/ So
32、lder pin 1 -018 5/ Solder-hook 3 1/ Over temperature range. 2/ With nominal coil voltage. 3/ From nominal coil voltage. 4/ For -005, -006, and -017, relays shall be tested to group A, type 1, ER screening requirements only, additional life testing, is not required. The alternate low level method sha
33、ll be used. 5/ Coil suppression (transient voltage back EMF) 42 V dc maximum. MIL-PRF-6106/13F11Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE II. Rated contact load (amperes per pole) (case grounded). Type of load Life operating cycles x 1032
34、8 V dc 115 V ac, 1 phase 115/200 V ac, 3 phase 1/ Main Aux Main Aux Main Aux NO NC NO NC 400 Hz 60 Hz 400 Hz 60 Hz 400 Hz 50 Hz 400 Hz 60 Hz Resistive 2/ 50 25 2 2 25 2 25 Inductive 10 12 1 1 Inductive 20 15 1 15 Motor 50 10 10 10 Lamp 50 5 .5 .5 5 .5 5 Transfer load 3/ Mechanical life reduced curre
35、nt 200 6 6 6 Intermediate current Applicable per specification (main contacts only) Mixed loads Applicable per specification 1/ Absence of value indicates relay is not rated for 3 phase application. 2/ For full rated load, maximum temperature, and altitude use no. 12 wire or larger. Solder hook rela
36、ys to be mounted to limit mounting bracket temperature to 160C for dc units and 135C for ac units. 3/ Transfer load indicates relay suitable for transfer between unsynchronized ac power supplies at rating indicated. MIL-PRF-6106/13F12Provided by IHSNot for ResaleNo reproduction or networking permitt
37、ed without license from IHS-,-,-MIL-PRF-6106/13F 13 Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for an
38、y inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced documents. In addition to MIL-PRF-6106, this document refe
39、rences the following: ASTM-B488 SAE-AMS3332 MIL-STD-202 MIL-STD-461 Custodian: Preparing activity: Air Force - 85 DLA - CC DLA-CC (Project 5945-2011-063)Review activities: Air Force - 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
