1、AMSC N/A FSC 5945 MIL-PRF-6106/26G 18 September 2012 SUPERSEDING MIL-PRF-6106/26F 02 December 2011 PERFORMANCE SPECIFICATION SHEET RELAYS, ELECTROMAGNETIC, 50 AMPERES SPST, NO, WITH 5 AMPERE SPDT AUXILIARY HERMETICALLY SEALED This specification is approved for use by all Departments and Agencies of
2、the Department of Defense. The requirements for acquiring the relay described herein shall consist of this specification sheet and MIL-PRF-6106. FIGURE 1. Relay, outline drawing.INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-6106/
3、26G 2 Inches mm Inches mm .005 0.13 .375 9.52 .010 0.25 .38 9.7.06 1.5 .437 11.10 .100 2.54 .44 11.2.11 2.8 1.91 48.5 .171 4.34 2.000 50.80.203 5.16 2.44 62.0 .31 7.9 2.50 63.5NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specif
4、ied, tolerances are .010 (0.25mm) for three place decimals and .03 (0.8 mm) for two place decimals. 4. Terminal numbers need not appear on the relay header providing there is affixed to the relay a suitable legible circuit diagram that identifies each terminal location specified. 5. Suppression leve
5、l - the maximum induced transient voltage (back EMF) shall be 50 volts, referenced to zero volts. 6. Terminal studs shall be rated at 171C. FIGURE 1. Relay, outline drawing - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-6106/26G
6、 3 TABLE I. Rated contact load (amperes per pole) (case grounded). Type of load Life oper-ating cycles X 10328 V dc 115 V ac, 1 phase 115/200 V ac, 3 phase Main Aux Main Aux Main Aux NO NC NO NC 400 50/60 400 50/60 400 50/60 400 50/60 Resistive 50 50 50 5 5 65 - 5 - - - - - Inductive 50 - - 3 3 65 -
7、 3 - - - - -Inductive 20 50 50 - - - - - - - - - - Motor - - - - - - - - - - - - - Lamp - - - - - - - - - - - - - Transfer, load - - - - - - - - - - - - - Mechanical life Reduced current - - - - - - - - - - - - - Intermediate current APPLICABLE PER SPECIFICATION REQUIREMENTS: COIL DATA: Nominal oper
8、ating voltage: 28 V dc. Maximum operating voltage: 29 V dc. Pickup voltage: 15 V dc, maximum, at 25C. Dropout voltage: 1.5 at 25C. Hold voltage: 7 V dc at 25C. Duty: continuous. Coil current: 0.280 ampere, maximum, at 28 V dc, 25C. OPERATIONAL DATA: Operate time: 35 milliseconds maximum with nominal
9、 coil voltage. Dropout time: 25 milliseconds maximum from nominal coil voltage. Contact load: See table I. Contact bounce time: 5 milliseconds, maximum. Contact drop: 150 millivolts, maximum, initially 175 millivolts, maximum, after life test. Overload current: 400 amperes ac, 125 amperes dc. Ruptur
10、e current: 500 amperes ac, 150 amperes dc. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-6106/26G 4 PHYSICAL DATA: Weight: 13 ounces, maximum. Strength of terminals and mounting studs: Applicable. Finish: Instrument black. Seal: Hermetic. T
11、erminal barriers: Base cover: Nonconductive. One type of insulator for meeting this requirement is MIL-I-24768/1. The insulator shall enable the product to meet the performance requirements of this specification. Barrier: Nonconductive. One type of insulator for meeting this requirement is PA110 G43
12、 A99900 KB207 UB090 PA176 E12 in accordance with ASTM-D4066. The insulator shall enable the product to meet the performance requirements of this specification. ENVIRONMENTAL DATA: Temperature range: -55C to +71C. Altitude: 60,000 feet. Dielectric withstanding voltage (sea level): Initial After life
13、tests Coil to case 1,000 V rms 1,000 V rms Aux contacts 1,000 V rms 1,000 V rms All other points 1,500 V rms 1,150 V rms Dielectric withstanding voltage (altitude): 60,000 feetCoil to case 500 V rms 500 V rms Aux contacts 500 V rms 500 V rms All other points 700 V rms 700 V rms Insulation resistance
14、: 100 megohms, minimum 500 volts. Vibration (sinusoidal): .06 D.A., 10 Hz to 55 Hz, 10 gs 55 Hz to 1,500 Hz, 15 gs, 55 Hz to 1,000 Hz. Shock: 25 gs for 11 milliseconds. Acceleration: 10 gs. Part number: M6106/26-001 Qualification by similarity: See MIL-PRF-6106. Changes from previous issue. The marg
15、ins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the
16、requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-6106/26G 5 Referenced documents. In addition to MIL-P
17、RF-6106, this document references the following: MIL-I-24768/1 ASTM-D4066 Custodian: Preparing activity: Air Force - 85 DLA - CC DLA - CC (Project 5945-2012-032)Review activities: Air Force 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
