1、AMSC N/A 1 of 5 FSC 5950 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. MIL-PRF-83446/36B 1 June 2012 SUPERSEDING MIL-PRF-83446/36A 16 September 2011 PERFORMANCE SPECIFICATION SHEET COILS, RADIO FREQUENCY, CHIP, OPEN CONSTRUCTION, SURFACE MOUNT, 0603 SIZE This spec
2、ification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-83446. INCHES MILLIMETERS A B C D E F 0.071 Max. 0.044 Max. 0.040 Max. 0.030 (Ref. Only) 0.018
3、 (Ref. Only) 0.008 (Ref. Only) 1.80 Max. 1.12 Max. 1.02 Max. 0.76 (Ref. Only) 0.44 (Ref. Only) 0.20(Ref. Only) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. FIGURE 1. Dimensions and configuration. INCH-POUND Provided by IHSNot for ResaleNo reproduc
4、tion or networking permitted without license from IHS-,-,-MIL-PRF-83446/36B 2 TABLE I. Electrical characteristics (initial). Dash Number Inductance nH 1/ Inductance Tolerance Percent () Inductance Test Frequency MHz Q (min) 1/ Q Test Frequency (MHz) Self Resonant Frequency MHz (min) 2/ DC Resistance
5、 Ohms (max) Current Rating mA (max) -01 -02 -03 -04 -05 -06 -07 -08 -09 -10 -11 -12 -13 -14 -15 -16 -17 -18 -19 -20 -21 -22 -23 -24 -25 -26 -27 -28 1.8 3.6 3.9 4.7 6.8 10 12 15 18 22 27 33 39 47 56 68 82 100 120 150 180 220 270 3.3 4.3 5.6 8.7 16 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10
6、 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 250 250 250 250 250 250 250 250 250 250 250 250 250 200 200 200 150 150 150 150 150 100 25 250 250 25
7、0 250 250 22 22 22 22 30 31 35 35 35 38 40 40 40 38 38 37 34 34 32 28 25 25 16 22 22 22 30 35 250 250 250 250 250 250 250 250 250 250 250 250 250 200 200 200 150 150 150 150 150 150 25 250 250 250 250 250 6000 6000 6000 6000 5800 4800 4000 4000 3100 3000 2800 2300 2200 2000 1900 1700 1700 1400 1300
8、990 990 700 600 6000 6000 5800 5200 3400 0.07 0.07 0.07 0.09 0.10 0.16 0.13 0.17 0.17 0.19 0.22 0.22 0.24 0.28 0.31 0.36 0.54 0.75 0.79 1.14 1.28 1.70 1.78 0.07 0.09 0.10 0.14 0.17 1000 1000 1000 885 840 665 735 645 645 610 565 565 540 500 475 440 360 305 300 245 235 200 195 1000 885 840 705 645 1/
9、Inductance and Q are tested using HP4291A or HP4287A with test fixture 16193A, or equivalent. 2/ Self resonant Frequency tested using HP8753C, or equivalent. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-83446/36B 3 TABLE II. Electrical cha
10、racteristics (final). Inspection group Allowable percent variation Qualification Inspection: Inductance 1/ Q 2/ Self-resonant Frequency 2/ DC resistance 1/ Group II Group IV Group V 5 5 5 -10 -10 -10 -8 -10 - 3 (+.001 ohm) 3 (+.001 ohm) - Quality Conformance Inspection: Group C Subgroup II Subgroup
11、IV Subgroup V 5 5 5 -10 -10 -10 -10 -8 - 2 (+.001 ohm) 3 (+.001 ohm) - 1/ From initial measurement. 2/ From specified minimum value in electrical characteristics (initial) table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-83446/36B 4 REQ
12、UIREMENTS: Dimensions and configuration: See figure 1. Bond strength: Force 1 pound. Weight: 0.008 gram, maximum. Operating temperature range: -55C to +125C. Temperature rise (at +90C): +35C. Maximum operating temperature: +125C. Altitude: 70,000 feet. Solderability: Test method S of J-STD-002, exce
13、pt solder preforms may be used or MIL-STD-202, method 208, test method B. Both terminals immersed simultaneously. Magnet wire and bond are excluded from solder coverage. Dielectric withstanding voltage: MIL-STD-202, method 301, test voltage 200 Vrms for 5 seconds for quality conformance. Barometric
14、pressure: MIL-STD-202, method 105, test condition C, (70,000 feet), test voltage 80 Vrms. DWV, Barometric pressure and Insulation resistance tests are to be performed with units mounted to a test substrate. Tests are moved to after visual/mechanical inspection of qualification Group I, and after ele
15、ctrical characteristics (initial) of subgroup II groupC. Electrical characteristics (initial): See table I. Electrical characteristics (final): See table II. Vibration: MIL-STD-202, method 204, test condition D. During testing, each part to be monitored for electrical continuity. Any discontinuity e
16、xceeding 100 microseconds shall be cause for rejection. Mechanical shock: MIL-STD-202, method 213, test condition I. After test, parts are to be inspected for mechanical damage and verified for electrical continuity. Vibration and Mechanical shock testing shall be performed as part of Group V tests
17、for qualification (before moisture resistance) and as part of subgroup V (semiannually) for group C testing. Parts shall be mounted on test substrates. Part or Identifying Number (PIN): The PIN shall be in the following form: M83446/36 -04 A G Sequentially assigned dash Numbers (see table I) Termina
18、tion finish (see MIL-PRF-83446) Inductance tolerance (see MIL-PRF-83446) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-83446/36B 5 Changes from previous issue. The margins of this specification are marked with vertical lines to indicate whe
19、re changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective o
20、f the marginal notations and relationship to the last previous issue. Referenced documents. MIL-PRF-83446 MIL-STD-202 J-STD-002 Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 85 (Project 5950-2012-003) DLA - CC Review activities: Army - MI Navy - AS, OS Air Force 19 NOTE: T
21、he activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
