1、MIL-R-L982F 73 W 9779706 023b07 5 W c_q3_G,o MIL-R-1982 F 31 March 1986 SUPERSEDING MIL-R-19 82E 29 December 1977 MILITARY SPECIFICATION ROLLS, CUTLERY, CANVAS This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This document cover
2、s canvas cutlery rolls. 1.2 Classification. Cutlery rolls shall be of the following types, as specified (see 6.2) : Type I - Component of Cooking Outfit, Field, Small Detachment Type II - Component of Accessory Outfit, Field Range, Gasoline 2. APPLICABLE DOCUMENTS * 2.1 Government documents. Unless
3、otherwise specified, the following documents of the issue in effect on date of invitation for bids or request for proposal form a part of this document to the extent specified herein. SPECIFICATIONS FEDERAL V-T-28 5 - Thread, Polyester E-L -2 7 1 - Leather, Cattlehide, Strap, Vegetable-Tanned Benefi
4、cial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to U.S. Army Natick Research, Development, and Engineering Center, Natick, MA 01760-5014, by using the self-addressed Standardization Document Improvement P
5、roposal (DD Form 1426) appearing at the end of this document or by letter. AMSC NIA FSC 7360 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. THIS DOCUMNT CONTAINS / 5 PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IH
6、S-,-,-_I_- MIL-R-LS2F 73 - 7777706 0238608 7 = MIL-R-1982F ccc-c-419 - Cloth, Duck, Cotton, Unbleached, Plied-Yarns, Army CCC-D-950 - Dyeing and Aftertreating Processes for Cotton Cloths DDD-L-20 - Label; For Clothing, Equipage, and Tentage, (General PPP-B-6 O1 - Boxes, Wood, Cleated-Plywood PPP-B-6
7、3 6 - Boxes, Shipping, Fiberboard and Numbered Use) MILITARY MIL-W-530 - Webbing, Textile, Cotton, General Purpose, Natural or MIL-T-43566 - Tape, Textile, Cotton, General Purpose, Natural or in in Colors Colors STANDARDS FEDERAL FED-STD-751 - Stitches, Seams and Stitchings MILITARY MIL-STD-105 - Sa
8、mpling Procedures and Tables for Inspection by MIL-STD-129 - Marking for Shipment and Storage MIL-STD-147 - Palletized Unit Loads MIL-STD-731 - Quality of Wood Members for Containers and Pallets Attributes DRAWINGS UmS. ARMY NATICK RESEARCH, DEVELOPMENT, AND ENGINEERING CENTER 5-7-44 - Roll, Cutlery
9、, Canvas, Type I; Assembly and Sections 5-7-45 - Roll, Cutlery, Canvas, Type I; Details 5-7 -102 - Roll, Cutlery, Canvas, Type II; Assembly and Sections 5-7-1 03 - Roll, Cutlery, Canvas, Type II; Patterns and Details (Copies of documents required by contractors in connection with specific acquisitio
10、n functions should be obtained from the contracting activity or as directed by the contracting officer. ) * 2.2 Other publications. Unless otherwise specified, the following document of the issue in effect on the date of invitation for bids or request for proposal forms a part of this document to th
11、e extent specified herein. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_- NIL-R-1982F 73 W 9999906 023b09 9 W MIL-R-1982F AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) D 3951 - Standard Practice for Commercial Packaging (Application for cop
12、ies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) (Technical society and technical association documents are generally 3 available for reference from libraries. They are also distributed among technical groups and using Federal agen
13、cies.) + 2.3 Order of precedence. In the event of conflict between the text of this document and the references cited herein, (except for associated detail specifications, specification sheets or MS standards), the text of this document shall take precedence. Nothing in this document, however, shall
14、 supersede applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 First article. When specified in the contract or purchase order, a sample shall be subjected to first article inspection (see 4.3, 6.2, and 6.3). 3.2 Materials and components. The materials
15、specified shall conform to applicable documents and requirements specified herein. 3.2.1 Cloth, duck, cotton. Cloth, before finishing, shall conform to type I, No. 6 hard texture and No. 10 hard texture of CCC-C-419. 3.2.1.1 Color and treatment. Cloth shall be dyed Olive Drab 7 and shall conform to
16、type I, class B of CCC-D-950. 3.2.2 Tape, textile, cotton. Tape shall be 3/4- and 1-inch widths, Olive Drab 7 and shall conform to type I, class 4 of MIL-T-43566. 3.2.3 Webbing, textile, cotton. Webbing shall be 2-inch width, Olive Drab 7 and shall conform to type IIb, class 4 of MIL-W-530. 3.2.4 Th
17、read, polyester. Thread for all stitching shall conform to type I, class 1, size FF of V-T-285. The thread shall be dyed shade S-1 (CA 66022). 3.2.5 Leather, cattlehide. Leather for the scabbards, in the thicknesses specified on Drawings 5-7-45, 5-7-102, and 5-7-103, shall conform to type I, II, III
18、, or IV, class 1 of KK-L-271, except that the colorfastness 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I - MIL-R-LS2F 73 7777706 0238610 5 MIL-R-1982F requirements shall not be applicable. The color of the leather shall be natural as produced
19、by the tanning agents. to the leather. A top finish need not be applied 3.3 Construction. Construction of the cutlery rolls shall conform to the drawings listed in section 2 and shall be as specified herein. 3.3.1 Stitching, machine. c 3.3.1.1 Stitch type. All stitching shall conform to type 301, 6
20、to 8 stitches per inch, of FED-STD-751 . 3.3.1.2 Thread breaks. Thread breaks in stitching shall be overstitched not less than 1 inch at each break. 3.3.1.3 Stitching ends. Stitching at the ends shall be overstitched not less than 1 inch, except where ends are turned under in a hem or held down by o
21、ther stitching. Where stitching is performed automatically on stitch patterns such as box, box with cross-stitch, “W“ stitching, or straight line tacking, at least three or more tying, overlapping, or backstitches shall be used to secure the ends. 3.3.1.4 Skipped stitches. Two or more skipped stitch
22、es occurring consecutively in type 301 stitching shall be overstitched not less than 1 inch. 3.4 Marking. All marking and labels shall conform to DDD-L-20. 3.4.1 Identification marking. Identification marking shall be in the location shown on Drawing 5-7-44 or 5-7-102, as applicable, and shall confo
23、rm to type IV, class 5. 3.4.2 Special marking. The item nomenclature, the letters “US“, the pocket numbers, and marking on the contents labels, in the location shown on Drawings 5-7-44 for type I or 5-7-102 for type II, shall conform to type IV, class 9, except that fastness shall be as specified fo
24、r class 5 labels. Copy for the contents lists for types I and II rolls shall be as listed in tables I and II, respectively. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-R-L9ZF 73 7777906 023bLL 7 MIL-R-1982F TABLE I. Contents list for type I
25、 roils Pocket No. Item Quantity 1 2 Fork, food preparation, 2-tine 15 inch 1 Stone, sharpening, pocket, 3 1/2 inch by 1 1/4 inch by 13/16 inch 1 3 Spoon, basting, 15 inch 1 4 Knife, cooks, 12 inch blade 1 5 Knives, paring 2 6 Openers, can, hand 2 TABLE II. Contents list for type II rolls Pocket No.
26、Ieem Quant i ty i Spoon, basting, 15 inch 2 2 Fork, food preparation, 15 inch 2 3 Knife, steak, scimitar 1 4 Knife, cook s 1 5 Knife, boning 1 6 Knife, paring 2 7 Peeler, potato, hand 3 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-R-L982F 73
27、 9999906 0238bL2 9 I MIL-R-1982F TABLE II. Contents list for type II rolls - Continued Pocket No. Item Quantity 8 9 10 Steel, butchers, smooth 1 Measuring set, spoon Saw, butchers 1 1 3.5 Workmanship. Cloth components shall be free of holes, cuts, tears, or cloth defects such as multiple floats or b
28、roken or missing yarns. Webbing and tape shall not have frayed or scalloped edges. maintained so that there will be no loose stitching and seam allowances shall be maintained with seams properly sewed so that no runoffs, pleats, twists, or open seams shall result. Care shall be taken in sewing to se
29、e that no needle chews occur. All thread ends shall be trimmed to 1/2 inch or less. Scabbards shall be free from any hole, cut, or loose spongy leather. Thread tension shall be 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase o
30、rder, the contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified he
31、rein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the document where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. * 4.1.1 Responsibility for compliance. All items m
32、ust meet all requirements of sections 3 and 5. part of the contractors overall inspection system or quality program. The absence of any inspection requirement in the document shall not relieve the contractor of the responsibility of assuring that all products or supplies submitted to the Government
33、for acceptance comply with all requirements of the contract. known defective material, either indicated or actual, nor does it commit the Government to acceptance of defective material. The inspection set forth in this document shall become a Sampling in quality conformance does not authorize submis
34、sion of 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-, MIL-R-1782F 73 m 7777706 0238613 O m MIL-R-19 82F * 4.1.2 Responsibility for dimensional requirements. Unless otherwise specified in the contract or purchase order, the contractor is respons
35、ible for assuring that all specified dimensions have been met. be examined on the end item, inspection shall be made at any point or at all points in the manufacturing process necessary to assure compliance with all dimensional requirements. When dimensions cannot 4.2 Classification of inspection. T
36、he inspection requirements specified herein are classified as follows: a. b. First article inspection (see 4.3). Quality conformance inspection (see 4.4). 4.3 First article inspection. When a first article is required (see 3.1), it shall be examined for the defects specified in table III and the spe
37、cified dimensions. first article. The presence of any defect shall be cause for rejection of the 4.4 Quality conformance inspection. Unless otherwise specified, sampling for inspection shall be performed in accordance with MIL-STD-105. 4.4.1 Component and material inspection. In accordance with 4.1,
38、 components and materials shall be inspected in accordance with all the requirements of referenced documents unless otherwise excluded, amended, modified, or qualified in this document or applicable purchase document. 4.4.1.1 Component dimensional examination. Examination shall be hade of the cut di
39、mensions of pocket pieces as shown on Drawings 5-7-45 and 5-7-103 for types I and II, as applicable. The lot shall be all pieces of the same letter designation offered for inspection at one time. The sample unit shall be one pocket piece. The inspection level shall be S-2, and the acceptable quality
40、 level (AQL), expressed in terms of defects per hundred units, shall be 4.0. n 4.4.2 End item visual examination. The end item shall be examined for the defects listed in table III. The lot size shall be expressed in units of rolls. and the acceptable quality level (AQL), expressed in terms of defec
41、ts per hundred units, shall be 2.5 for major defects and 6.5 for total (major and minor combined) defects. The sample unit shall be one roll. The inspection level shall be II 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-R-LSB2F 73 9999906 02
42、38bL9 2 MIL-R-1982F TABLE III. End item visual defects Examine Defect Classification Fabric Seams and stitching Any hole, cut, or tear Broken or missing yarn, multiple floats visible at normal inspection distance (approximately 3 feet) Shade bar Fine or coarse filling bar Open seam: -for more than 1
43、 inch -for not more than 1 inch NOTE: A seam shall be classified as open when one or more stitches joining a seam are broken, or when one or more skipped or runoff stitches occur. On double- stitched seams, a seam shall be classified as open when either one or both sides of a seam are open. Raw edge
44、 more than 1/2 inch Thread break overstitched less than 1 inch NOTE: Thread breaks not overstitched shall be classified as open seams. Skipped stitches overstitched less than 1 inch (when two or more consecutive skipped stitches occur) NOTE: Skipped stitches not overstitched shall be classified as o
45、pen seams. Needle chew resulting in cut or tear larger than 1/8 inch in length or hole larger than 1/8 inch in diameter Major Minor - X X X X X X X X X X 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-R-3782F 73 = 777770b 0238635 4 MIL-R-1982F
46、 TABLE III. End item visual defects - Continued Classification Examine Defect - Major Minor Seams and stitching (continued) Stitching ends One or more required rows of stitching omitted X Overstitched less than 1 inch (except where ends are held down by other stitching or turned under in a hem) X S
47、eams Seam pleated X Seam type Wrong seam type X Stitch type Wrong stitch type X Stitch tension Loose, resulting in exposed bobbin or top thread, for more than 2 inches Tight, as evidenced by puckering of fabric on seams, for more than 2 inches X X Stitches per inch Less than minimum specified More t
48、han maximum specified X X Stitching gage Not as specified X Stitching margin Variation from specified margin by more than 1/16 inch X Binding Loosely or improperly applied X X Scabbard Hole, cut, or loose spongy leather Components and as semb ly Any component part not fabricated of applicable refere
49、nced material X 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-R-LS2F 73 7979906 0238616 b MIL-R-1982F TABLE III. End item visual defects - Continued Examine Defect Classification Major Minor - Markings Cleanness Omitted, incorrect, illegible, or misplaced Grease or oil stains, thread ends not trimmed to 1/2
