1、AMSC N/A FSC 5950 INCH-POUND MIL-T-27/160B 9 November 2009 SUPERSEDING MIL-T-27/160A 4 April 1980 MILITARY SPECIFICATION SHEET TRANSFORMER AND INDUCTORS (AUDIO, POWER AND HIGH-POWER PULSE), INDUCTION, POWER This specification is approved for use by all Depart- ments and Agencies of the Department of
2、 Defense. The requirements for acquiring the transformer described herein shall consist of this specification sheet and MIL-PRF-27. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerance on overall case dimensions is
3、 .016 inch (0.41 mm). 4. Marking shall be on the side of the case. FIGURE 1. Dimensions and configurations Inactive for new design after 25 August 1998 .1881.9382.125MAX.1.470MAX.660MAX.MALCO NO. 1472 TERMINAL OR EQUIVALENT 2 REQD .3121.859MAX. ALTITUDE: 70,000 FT. MAX. WORKING VOLTAGE: (PEAK) 1,070
4、 V 1 2 10 H 200mA dc 10 V, 60 Hz CIRCUIT DIAGRAM AND MARKING 1.360 MAX. .395 MAX. .156 DIA.(4 HOLES).203 1.547 1.750 MAX. Inches mm Inches mm .016 0.41 1.360 34.54 .156 3.96 1.470 37.34 .188 4.78 1.547 39.29 .203 5.16 1.750 44.45 .312 7.92 1.859 47.22 .395 10.03 1.938 49.23 .660 16.76 2.125 53.98 Pr
5、ovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-27/160B 2 REQUIREMENTS: (When numbers in parentheses, such as (1-2) are used, they indicate the winding and the extreme terminals of the winding.) Electrical ratings: See table I. Inductance (1-2):
6、1.0 H, minimum. Voltage (1-2): 10 volts, 60 Hz. Current (1-2): 200 mA dc. DC resistance (1-2): 69 ohms, maximum. Working voltage (Peak): 1,070 volts. Power: 2.2 watts Design and construction: Dimensions and configuration: See figure 1. Duty cycle: Continuous. Case: Encapsulated. Material: Epoxy. Ter
7、minals: Solder terminal, Malco No 1472 or equivalent. Height: .312 .016 inch (7.92 0.41 mm). Weight: 408 grams, maximum. Altitude: 70,000 feet, maximum. Operating temperature range: -55C to +130C. Terminal strength: MIL-STD-202, method 211, test condition A, 5.0 pounds. Vibration (high frequency): M
8、IL-STD-202, method 204. Dielectric withstanding voltage: At sea level: 2,500 volts rms. At barometric pressure: 1,337.5 volts rms. Electrical characteristics: Inductance: With 10 volts, 60 Hz across (1-2), and 200 mA dc applied to (1-2) the inductance shall be 1.0 H minimum. Temperature rise: 45C wi
9、th 10 volts, 60 Hz, 200 mA dc applied to (1-2) at an ambient temperature of 85C. Marking location: See figure 1. Part or Identification Number (PIN): M27/160-01. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-27/160B 3 Changes from previous is
10、sue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to
11、evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced documents. In addition to MIL-PRF-27, this document references the following: MIL-STD-202 Custodians: Preparing activity: Army - CR DL
12、A - CC Navy - EC Air Force - 85 (Project 5950-2009-010) DLA - CC Review activities: Army - AR, CR4 Navy - AS, MC, OS, SH Air Force - 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
