1、 MS14046D 29 June 2007 SUPERSEDING MS14046C 2 June 2003 MILITARY SPECIFICATION SHEET COILS, RADIO FREQUENCY, MOLDED, FIXED, MICROMINIATURE, (IRON CORE) TYPES LT10K128 TO LT10K137 This specification is approved for use by all Depart- ments and Agencies of the Department of Defense. The requirements f
2、or acquiring the products described herein shall consist of this specification and MIL-PRF-15305. Dimensions in inches with metric equivalents (mm) in parentheses Ltr Minimum Maximum A B C D .146 ( 3.71) .365 ( 9.27) 1.250 (31.75) .023 ( 0.58) .166 ( 4.22) .385 ( 9.78) 1.625 (41.28) .027 ( 0.69) NOT
3、ES: 1. Dimensions are in inches. 2. Metric equivalents, in parentheses, are given for general information only. 3. These coils are intended to be mounted by their leads. 4. Solderable/weldable lead wire, AWG number 22. FIGURE 1. Dimensions and configuration. AMSC N/A FSC 5950 INCH-POUND Inactive for
4、 new design after 16 September 1985. For new design, use MIL-PRF-39010/7.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS14046D 2 REQUIREMENTS: Design, construction, and physical dimensions: See figure 1. Style: LT10. Grade: 1. Class: A. Weight: 0.
5、0317 ounce maximum. Operating temperature range: -55C to +105C. Ambient temperature: 90C maximum. Temperature rise: 15C maximum. Terminal pull: 5 pounds minimum. Altitude: 70,000 feet. Shock, specified pulse: MIL-STD-202, method 213, test condition I, is applicable. Dielectric withstanding voltage:
6、At sea level: MIL-STD-202, method 301, test voltage 1,000 V rms for a minimum of 60 seconds. At reduced barometric pressure: MIL-STD-202, method 105, test condition C, test voltage 200 V rms for a minimum of 60 seconds. Electrical characteristics: See table I and table II. Inductance: See table I. Q
7、 values: See table I. Self-resonant frequency (SRF): See table I. DC resistance (DCR): See table I. Part or Identifying Number (PIN): MS14046- (dash number from table I). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS14046D 3 TABLE I. Electrical
8、characteristics (initial). Dash number 1/ Type designation 2/ Superseded MS PIN Inductance (H) 10% Q (min) Test frequency (MHz) SRF min (MHz) DC resistance (ohms) Rated dc current (mA) -1 LT10K128 MS18130-17 5.60 45 7.9 60 .32 495 -2 LT10K129 MS18130-18 6.80 50 7.9 55 .50 395 -3 LT10K130 MS18130-19
9、8.20 50 7.9 50 .60 360 -4 LT10K131 MS18130-20 10.00 55 7.9 45 .90 290 -5 LT10K132 MS18130-21 12.00 65 2.5 42 1.10 265 -6 LT10K133 MS18130-22 15.00 65 2.5 40 1.40 240 -7 LT10K134 MS18130-23 18.00 75 2.5 34 2.25 185 -8 LT10K135 MS18130-24 22.00 75 2.5 30 2.50 175 -9 LT10K136 MS18130-25 27.00 60 2.5 25
10、 2.60 170 -10 LT10K137 MS18130-26 33.00 65 2.5 19 3.00 165 1/ The dash number added to MS military standard number constitutes the MS PIN; for example MS14046-1. 2/ The decrease in maximum operating temperature from 125C to 105C does not downgrade these coils but assures satisfactory operation at 10
11、5C for a minimum of 2,000 hours of life rather than a shorter period of operation at 125C. TABLE II. Electrical characteristics (final). 1/ Allowable variation from Initial measurement Allowable percent from specified minimum value in electrical characteristics (initial) table Inspection group Induc
12、tance (percent) DC resistance Self-resonant frequency Q Qualification inspection Group II Group III Group IV 2/ 2 5 5 - (3% +.001 ohm) (2% +.001 ohm) - -8 -10 -10 -10 -15 Conformance inspection group C Subgroup I Subgroup II 2/ Subgroup III 2 5 5 - (2% +.001 ohm) (3% +.001 ohm) - -10 -8 -10 -15 -10
13、1/ Test fixture allowance of +.01 H shall be added to all change in inductance limits ( _ percent +.01 H). 2/ The polarizing voltage during the moisture resistance tests Is applied with the positive lead connected to the coil terminals tied together, and the negative lead connected to the metal stra
14、p. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS14046D 4 Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience on
15、ly and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Reference
16、d documents. In addition to MIL-PRF-15305, this document references MIL-STD-202. Custodians: Preparing activity: Army CR DLA CC Navy EC Air Force 11 (Project 5950-2007-004) DLA - CC Review activities: Army AR, CR4, MI Navy AS, MC, OS, SH Air Force 19 NOTE: The activities listed above were interested
17、 in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
