1、 DETAIL SPECIFICATION SHEET INSERT ARRANGEMENTS, ELECTRICAL CONNECTOR, SIZE 28, CLASS L, 40 AMPS This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet
2、and MIL-DTL-22992. Quantity Contact Size Socket SAE-AS39029/49 M39029- Pin SAE-AS39029/48 M39029- 1 A 6 329 317 1 N 6N 329 (see note 6) 318 NOTES: 1. Dimensions are in inches. Metric equivalents are given for information only. Unless otherwise specified, tolerance is .002 (.05 mm). 2. Unless otherwi
3、se specified, front face of pin insert pattern is shown. Socket inserts are the reverse. 3. -02-Cable IPCEA 2-NO 8 conductor round type W. 4. -03-Cable-C0-02-HDF (2/6) 0930 in accordance with MIL-DTL-3432. 5. Mark 28-02 on 28-03 insert. Trademark and 28-( ) shall appear in available space. Contact i
4、dentifying letter shall be located so as to identify relative contact. 6. Only the pin contact is lengthened and has the N (neutral) designation. The mating socket contact is the same as the power contact. FIGURE 1. 28 volt DC two wire, -02 and -03 insert arrangements, service D. AMSC N/A FSC 5935 M
5、S14054F 8 May 2013 SUPERSEDING MS14054E 26 October 2005 INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS14054F 2 Quantity Contact Size Socket SAE-AS39029/49 M39029- Pin SAE-AS39029/48 M39029- 1 A 6 329 317 1 G, N 6N 329 (see note 6) 318
6、NOTES: 1. Dimensions are in inches. Metric equivalents are given for information only. Unless otherwise specified, tolerance is .002 (.05 mm). 2. Unless otherwise specified, front face of pin insert pattern is shown. Socket inserts are the reverse. 3. -04-Cable IPCEA 2-NO 8 conductor round type G. 4
7、. -05-Cable-C0-02-HDF (2/6-2/10R) 0930 in accordance with MIL-DTL-3432. 5. Mark 28-04 on 28-05 insert. Trademark and 28-( ) shall appear in available space. Contact identifying letter shall be located so as to identify relative contact. 6. Only the pin contact is lengthened and has the N (neutral) d
8、esignation. The mating socket contact is the same as the power contact. FIGURE 2. AC single phase two wire grounding, -04 and -05 insert arrangements, service D. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS14054F 3 Quantity Contact Size Socket
9、SAE-AS39029/49 M39029- Pin SAE-AS39029/48 M39029- 2 A, B 6 329 317 1 N 6N 329 (see note 6) 318 1 G 4N 331 (see note 6) 321 NOTES: 1. Dimensions are in inches. Metric equivalents are given for information only. Unless otherwise specified, tolerance is .002 (.05 mm). 2. Unless otherwise specified, fro
10、nt face of pin insert pattern is shown. Socket inserts are the reverse. 3. -06-Cable IPCEA 3-NO 8 conductor round type G. 4. -07-Cable-C0-03-HDF (3/6-3/10R) 1000 in accordance with MIL-DTL-3432. 5. Mark 28-06 on 28-07 insert. Trademark and 28-( ) shall appear in available space. Contact identifying
11、letter shall be located so as to identify relative contact. 6. Only the pin contact is lengthened and has the N (neutral) designation. The mating socket contact is the same as the power contact. FIGURE 3. AC single phase three wire grounding, -06 and -07 insert arrangements, service D. Provided by I
12、HSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS14054F 4 Quantity Contact Size Socket SAE-AS39029/49 M39029- Pin SAE-AS39029/48 M39029- 3 A, B, C 6 329 317 2 N, G 6N 329 (see note 6) 318 NOTES: 1. Dimensions are in inches. Metric equivalents are given for infor
13、mation only. Unless otherwise specified, tolerance is .002 (.05 mm). 2. Unless otherwise specified, front face of pin insert pattern is shown. Socket inserts are the reverse. 3. -12-Cable IPCEA 4-NO 8 conductor round type G. 4. -13-Cable-C0-04-HDF (4/6-4/12R) 1090 in accordance with MIL-DTL-3432. 5.
14、 Mark 28-12 on 28-13 insert. Trademark and 28-( ) shall appear in available space. Contact identifying letter shall be located so as to identify relative contact. 6. Only the pin contact is lengthened and has the N (neutral) designation. The mating socket contact is the same as the power contact. FI
15、GURE 4. AC three phase four wire grounding, -12 and -13 insert arrangements, service D. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS14054F 5 Insert rotation (degrees from normal) Arrangement number Normal DC or 60 Hz (see figures 6 through 9) A
16、lternate (see figures 6 through 9) 400 Hz W X Y 28 04 28 05 0 - - 180 28 06 28 07 0 - - - 28 12 28 13 0 - - 180 28 03 28 02 0 - - - FIGURE 5. Insert arrangements and rotations. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS14054F 6 NOTES: 1. For
17、use with connectors under MS90555 and MS90557 utilizing socket contacts and normal keying. 2. Front face of socket insert shown. FIGURE 6. Socket contact pattern and polarization, insert in normal position (60 Hz power only). Provided by IHSNot for ResaleNo reproduction or networking permitted witho
18、ut license from IHS-,-,-MS14054F 7 NOTES: 1. For use with connectors under MS90555 and MS90557 utilizing socket contacts and alternate (Y) keying. 2. Front face of socket insert shown. FIGURE 7. Socket contact pattern and polarization, insert in alternate position (400 Hz power only). Provided by IH
19、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS14054F 8 NOTES: 1. For use with connectors under MS90556 and MS90558 utilizing pin contacts and normal keying. 2. Front face of pin insert shown. FIGURE 8. Socket contact pattern and polarization, insert in normal
20、position (60 Hz power only). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS14054F 9 NOTES: 1. For use with connectors under MS90556 and MS90558 utilizing pin contacts and alternate (Y) keying. 2. Front face of pin insert shown. FIGURE 9. Socket c
21、ontact pattern and polarization, insert in alternate position (400 Hz power only). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS14054F 10 REQUIREMENTS: Design and construction, see figures 1 through 9 and table I. Neutral pin (N) is not connecte
22、d to shell. Grounding pin (G) is connected to shell. Applicable SAE-AS39029/112 crimp bushings shall be supplied with the contacts for insert arrangements as specified. TABLE I. Accessories. Insert arrangement Contacts Cable conductors MS90556 and MS90557 1/ Contact bushings required (in accordance
23、with SAE-AS39029/112) Quantity Size Quantity Size Quantity PIN MS3348- 28 02 2 6 2 B 2 6-BL 28 04 2 1 6 6 2 2 8 10(G) 2 - 6-8L - 28 06 3 1 6 4 3 3 8 12(G) 3 1 6-8L 4-8L 28 07 3 1 6 4 3 3 7 10(G) - 1 - 4-6L 28 12 4 1 6 6 4 4 8 12G 4 - 6-8L - 1/ (G) designates grounding. Changes from previous issue. T
24、he margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evalua
25、te the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced documents. In addition to MIL-DTL-22992, this document references the following: MIL-DTL-3432 MS90555 MS90556 MS90557 MS90558 SAE-AS39029/48
26、 SAE-AS39029/49 SAE-AS39029/112 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS14054F 11 CONCLUDING MATERIAL Custodians: Preparing activity: Army CR DLA CC Navy EC Air Force 85 DLA CC Review activities: (Project 59352013-093) Army AT, AV, CR4, MI
27、Navy AS, CG, MC, OS, YD Air Force 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
