1、 MS3111E INCH-POUND29 April 2009 SUPERSEDING MS3111D 1 March 2007 DETAIL SPECIFICATION SHEET CONNECTORS, PLUG, ELECTRICAL, SOLDER TYPE, CABLE CONNECTING, BAYONET COUPLING, SERIES 1, CLASSES E, F, J AND P Inactive for new design after 15 December 1998. For new design, use MS3476. This specification i
2、s approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-26482. FIGURE 1. Plug, classes E, F, J, and P, pin and socket inserts. AMSC N/A FSC 5935 Provided by IHSN
3、ot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS3111E 2FIGURE 1. Plug, classes E, F, J, and P, pin and socket inserts - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS3111E 3Shell size A max length B
4、dia .020 across flange corners F + .031 - .000 mounting flange location G .016 thick mounting flange N UNEF-2A accessory thread R max ID gasket 8 .828 (21.03) .938 (23.83) .4375-28 .329 (8.36) 10 .954 (24.23) 1.062 (26.97) .5625-24 .457 (11.61) 12 1.047 (26.59) 1.156 (29.36) .6875-24 .564 (14.33) 14
5、 1.141 (28.98) 1.250 (31.75) .8125-20 .689 (17.50) 16 1.234 (31.34) 1.344 (34.14) .9375-20 .814 (20.68) 18 1.328 (33.73) 1.438 (36.53).400 (10.16) .094 (2.39) 1.0625-18 .907 (23.04) 20 1.453 (36.91) 1.562 (39.67) 1.1875-18 1.039 (26.39)22 1.578 (40.08) 1.688 (42.88).535 (13.59) 1.3125-18 1.164 (29.5
6、7)24 1.700 (43.18) 1.812 (46.02) .558 (14.17) .115 (2.92) 1.4375-18 1.289 (32.74)Inches mm Inches mm .005 0.13 .020 0.51 .010 0.25 .031 0.79 .015 0.38 .070 1.78 .016 0.41 .156 3.96 INSERT STYLES P AND S NOTES: 1. Dimensions are in inches. Metric equivalents are given for information only. 2. True po
7、sition (TP) tolerances specified are in accordance with ASME Y14.5M. 3. Intermateability dimensions shall be in accordance with MIL-DTL-26482. FIGURE 1. Plug, classes E, F, J, and P, pin and socket inserts - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without lice
8、nse from IHS-,-,-MS3111E 4Shell size L max overall length X dia min ID Y dia max OD 8 .259 (6.58) .608 (15.44) 10 .359 (9.12) .734 (18.64) 12 .469 (11.91) .858 (21.79) 14 .589 (14.96) .984 (24.99) 16 .727 (18.47) 1.110 (28.19) 18 1.328 (33.73) .779 (19.79) 1.234 (31.34) 20 .901 (22.89) 1.360 (34.54)
9、 22 1.531 (38.89) 1.009 (25.63) 1.484 (37.69) 24 1.594 (40.49) 1.123 (28.52) 1.610 (40.89) NOTES: 1. Dimensions are in inches. Metric equivalents are given for information only. 2. True position (TP) tolerances specified are in accordance with ASME Y14.5M. 3. Intermateability dimensions shall be in
10、accordance with MIL-DTL-26482. FIGURE 2. Plug, rear accessories configurations, class E. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS3111E 5CLASS F, WITH BUSHING CLASS F, WITH BUSHING REMOVED FIGURE 3. Plug, rear accessories configurations, cla
11、ss F. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS3111E 6Shell size L max overall length X dia min open Y dia max N (see note 4) .010 free dia ZZ screw threads YZ (see note 5) Lockwashers NASM 35338 or NASM 35333 types 8 .234 (5.94) .828 (21.03
12、) .125 (3.18) 10 .297 (7.54) .891 (22.63) .188 (4.78) 12 .422 (10.72) 1.016 (25.81) .312 (7.92) 14 1.922 (48.82) .547 (13.89) 1.161 (29.49) .375 (9.53) 16 2.047 (51.99) .609 (15.47) 1.203 (30.56) .500 (12.70) 6-32 UNC NASM 35338 -98 or -41 NASM 35333 -105 or -37 18 2.078 (52.78) .625 (15.88) 20 .734
13、 (18.64) 1.469 (37.31) .625 (15.88) 22 2.344 (59.54) .922 (23.42) 1.656 (42.06) .750 (19.05) 24 2.406 (61.11) .984 (24.99) 1.750 (44.45) .800 (20.32) 8-32 UNC NASM 35338 -99 or -42 NASM 35333 -106 or -38 NOTES: 1. Dimensions are in inches. Metric equivalents are given for information only. 2. True p
14、osition (TP) tolerances specified are in accordance with ASME Y14.5M. 3. Intermateability dimensions shall be in accordance with MIL-DTL-26482. 4. Use MS3420 bushing if reduced opening is required. 5. Lockwashers may be captivated. FIGURE 3. Plug, rear accessories configurations, class F Continued.
15、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS3111E 7X ID gland seal min range Shell size L max overall length V max closed Closed Open Y dia max ZZ screw threads YZ (see note 4) Lockwashers NASM35338 or NASM35333types 8 .157 (3.99) .168 (4.27) .
16、230 (5.84) .828 (21.03) 10 2.271 (57.68) .187 (4.75) .205 (5.21) .312 (7.92) .891 (22.63) 12 2.411 (61.24) .281 (7.14) .338 (8.59) .442 (11.23) 1.016 (25.81) 14 2.599 (66.01) .325 (8.26) .416 (10.57) .539 (13.69) 1.141 (28.98) 16 2.943 (74.75) .356 (9.04) .550 (13.97) .616 (15.65) 1.203 (30.56) 18 3
17、.172 (80.57) .456 (11.58) .600 (15.24) .672 (17.07) 6-32 UNC NASM35338 - 98 or -41 NASM35333-105 or -37 20 3.610 (91.69) .635 (16.13) .747 (18.97) 1.469 (37.31) 22 3.766 (95.66) .519 (13.18) .670 (17.02) .846 (21.49) 1.656 (42.06) 24 3.985 (101.22) .657 (16.69) .760 (19.30) .894 (22.71) 1.750 (44.45
18、) 8-32 UNC NASM35338 -99 or -42 NASM35333-106 or -38 NOTES: 1. Dimensions are in inches. Metric equivalents are given for information only. 2. True position (TP) tolerances specified are in accordance with ASME Y14.5M. 3. Intermateability dimensions shall be in accordance with MIL-DTL-26482. 4 Lockw
19、ashers may be captivated. FIGURE 4. Plug, rear accessories configurations, class J. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS3111E 8Shell Size L max overall length X dia min ID Y dia max OD PP min 8 .317 (8.05) .608 (15.44) 10 .434 (11.02) .
20、734 (18.64) 12 .548 (13.92) .858 (21.79) 14 .673 (17.09) .984 (24.99) 16 .798 (20.27) 1.110 (28.19) 18 1.453 (36.91) .899 (22.83) 1.234 (31.34) 20 1.024 (26.01) 1.360 (34.54) 22 1.672 (42.47) 1.149 (29.18) 1.686 (42.82) 24 1.734 (44.04) 1.274 (32.36) 1.610 (40.89) .250 (6.35) NOTES: 1. Dimensions ar
21、e in inches. Metric equivalents are given for information only. 2. True position (TP) tolerances specified are in accordance with ASME Y14.5M. 3. Intermateability dimensions shall be in accordance with MIL-DTL-26482. FIGURE 5. Plug, rear accessories configurations, class P. Provided by IHSNot for Re
22、saleNo reproduction or networking permitted without license from IHS-,-,-MS3111E 9REQUIREMENTS: Dimensions and configurations: See figures 1 through 5. Connector mating: This connector mates with MS3110, MS3112 through MS3115, MS3119, MS3120, MS3122, MS3124, MS3127 and MS3128. Intermateability dimen
23、sions are in accordance with MIL-DTL-26482. For insert arrangement: See MIL-STD-1669. Finishes: When finish W is required, the finish designator shall not be included in the PIN. See MIL-DTL-26482 for other finishes, including D, T and Z, available for classes E, F and P. Part or Identifying Number
24、(PIN) example: MS3111 F 12 -3 P W D MS number Class Shell size Insert arrangement Contact style Alternate insert position Finish Note: When finish W is required, no finish designator is used (finish W is the default finish). Changes from previous issue. Marginal notations are not used in this revisi
25、on to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents. In addition to MIL-DTL-26482, this document references the following: MS3110 MS3112 MS3113 MS3114 MS3115 MS3119 MS3120 MS3122 MS3124 MS3127 MS3128 MS3420 MS3476 MIL-STD-1669 ASME Y14.5M
26、NASM35333 NASM35338 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS3111E 10CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA - CC Navy - AS Air Force - 85 (Project 5935-2007-178) DLA - CC Review activities: Army - AV Navy - EC, SH
27、Air Force - 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
