1、 INCH-POUND MS8002D w/AMENDMENT 1 09 September 2005 SUPERSEDING MS8002D 24 September 2003 DETAIL SPECIFICATION SHEET HOSE ASSEMBLY, POLYTETRAFLUOROETHYLENE, REUSABLE FITTINGS, HIGH TEMPERATURE, MEDIUM PRESSURE, FLARE-TO-FLANGE This specification is approved for use by all Departments and Agencies of
2、 the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-25579. Hose cut-off factor (HCOF) for assembly with class 1 fittings: See table l. TABLE I. HCOF for assembly with class 1 fittings. 1/ Fitting ends HCOF (siz
3、e vs length) 3/ Style 2/ Corrosion resistant steel (CRES) 1 2 8 10 12 16 20 24 A MS27053 MS27054 2.16 2.47 2.51 2.91 3.13 3.47 B MS27053 MS27056 2.18 2.47 3.03 3.28 3.66 4.16 C MS27053 MS27058 2.14 2.46 3.05 3.35 3.78 4.34 MS27059 MS27056 3.04 D MS27055 MS27056 3.00 3.95 4.12 4.64 5.25 MS27059 MS270
4、58 3.00 E MS27055 MS27058 2.99 3.97 4.19 4.76 5.43 MS27060 MS27058 2.52 F MS27057 MS27058 2.82 3.84 4.10 4.68 5.36 MS27059 MS27054 3.02 G MS27055 MS27054 3.00 3.43 3.75 4.11 4.56 MS27060 MS27054 2.54 H MS27057 MS27054 2.83 3.30 3.66 4.03 4.49 MS27060 MS27056 2.56 J MS27057 MS27056 2.83 3.82 4.03 4.5
5、6 5.18 1/ Class 1 fittings, styles A through J, are made from CRES. 2/ For depiction of styles see figure 1. 3/ The HCOF is used in the following calculation to determine the hose length required to produce an assembly of a specific size, style and length: Assembly length - HCOF = Hose length. For e
6、xample, the hose length required to produce an 25.50 inch length assembly of size 10, style J is calculated as follows: 25.50 - 2.83 = 22.67. AMSC N/A FSC 4720 Source: http:/assist.daps.dla.mil - Downloaded: 2005-09-30T07:29ZCheck the source to verify that this is the current version before use.Prov
7、ided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8002D w/AMENDMENT 1 2 HCOF for assembly with class 2 fittings: See table ll. TABLE II. HCOF for assembly with class 2 fittings. 1/ Fitting ends HCOF (size vs length) 3/ Styles 2/ (Aluminum and CRES) 1 2 8
8、 10 12 16 20 24 K MS27053 MS27054 2.16 2.47 2.51 2.91 3.13 3.47 M MS27053 MS27056 2.18 2.47 3.03 3.28 3.66 4.16 N MS27053 MS27058 2.14 2.46 3.05 3.35 3.78 4.34 MS27059 MS27056 3.04 P MS27055 MS27056 3.00 3.95 4.12 4.64 5.25 MS27059 MS27058 3.00 R MS27055 MS27058 2.99 3.97 4.19 4.76 5.43 MS27060 MS27
9、058 2.52 S MS27057 MS27058 2.82 3.84 4.10 4.68 5.36 MS27059 MS27054 3.02 T MS27055 MS27054 3.00 3.43 3.75 4.11 4.56 MS27060 MS27054 2.54 U MS27057 MS27054 2.83 3.30 3.66 4.03 4.49 MS27060 MS27056 2.56 V MS27057 MS27056 2.83 3.82 4.03 4.56 5.18 1/ Class 2 fittings, styles K through V, are made from c
10、ombination of aluminum and CRES. 2/ See figure 1 for depiction of styles. 3/ The HCOF is used in the following calculation to determine the hose length required to produce an assembly of a specific size, style and length: Assembly length - HCOF = Hose length. For example, the hose length required to
11、 produce an 25.50 inch length assembly of size 10, style J is calculated as follows: 25.50 - 2.83 = 22.67. Source: http:/assist.daps.dla.mil - Downloaded: 2005-09-30T07:29ZCheck the source to verify that this is the current version before use.Provided by IHSNot for ResaleNo reproduction or networkin
12、g permitted without license from IHS-,-,-MS8002D w/AMENDMENT 1 3 Protective sleeve code: See table III. TABLE III. Protective sleeve code. Code TypeA SAE AS1072 sleeve, fire protection, silicone covered, temperature ranging from -65F to 450F and intermittently to 500F, secured with CRES bands as req
13、uired. 1/ B SAE AS1073 - code B sleeve, abrasion protection, heat shrinkable, black polyolefin, temperature ranging from -65F to 250 F. C SAE AS1291 - code A sleeve, chafe guard, extruded seamless white PTFE, temperature ranging from -65F to 450F, secured with CRES bands as required. D SAE AS1291 -
14、code C sleeve, chafe guard, extruded seamless transparent FEP, temperature ranging from -65F to 350F, secured with CRES bands as required. E SAE AS1298 sleeve, heavy wall chafe guard, extruded seamless black PTFE, temperature ranging from -65F to 450F, secured with CRES bands as required. L Lock-wir
15、e hole F Code A + L G Code B + L H Code C + L J Code D + L K Code E + L 1/ To prevent wicking of fluids, the cut end of the fire protective sleeve (code A) shall be coated with Room Temperature Vulcanized (RTV) silicone rubber prior to installation. After installation, cracks and voids in the fire p
16、rotective sleeve shall be coated with RTV rubber to prevent exposure of fiberglass.Source: http:/assist.daps.dla.mil - Downloaded: 2005-09-30T07:29ZCheck the source to verify that this is the current version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without lice
17、nse from IHS-,-,-MS8002D w/AMENDMENT 1 4 NOTES: Class 1 fittings (450F) Corrosion resistant steel Class 2 fittings (275F) Combination aluminum and corrosion resistant steel End 1 End 2 End 1 End 2 1. See tables I and II for fitting ends and HCOF. 2. Fittings shall mate with parts designed to SAE AS4
18、395 and the mounting pad as shown on MS33786. FIGURE 1. Classes 1 and 2 hose assembly styles with flare-to-flange reusable fittings. Source: http:/assist.daps.dla.mil - Downloaded: 2005-09-30T07:29ZCheck the source to verify that this is the current version before use.Provided by IHSNot for ResaleNo
19、 reproduction or networking permitted without license from IHS-,-,-MS8002D w/AMENDMENT 1 5 REQUIREMENTS Dimensions: Unless otherwise specified, all dimensions are in inches. Fittings: All fittings shall be qualified in accordance with MIL-DTL-27272. Hose: The hose shall be qualified in accordance wi
20、th MIL-DTL-27267. Assembly classification: Class 1 and class 2 hose assemblies, as specified in MIL-DTL-25579, have been incorporated into the Part or Identifying Number (PIN) as a part of styles (see tables I and II and figure 1). Angular alignment: Hose assemblies with elbow fittings on each end s
21、hall have the angular orientation between the elbows measured counter-clockwise from the centerline of the nearest fitting, positioned at six-oclock, to the centerline of the other fitting (see figure 2). The elbow fitting drop height shall be as shown on figure 3 and table IV. When applicable, the
22、angular alignment shall be expressed in three digits and specified in the PIN. Protective sleeve: If required, the hose assembly shall include a protective sleeve (see table III) and its code shall be included in the PIN. Fire protective sleeve shall be subjected to testing in accordance with MIL-DT
23、L-25579. Assembly length: Hose assembly shall be furnished in lengths as specified in the contract or purchase order (see MIL-DTL-25579); however, tolerances on the length of each hose assembly shall be as follows: a. 1/8 inch for lengths under 18 inches. b. 1/4 inch for lengths from 18 inches to 36
24、 inches. c. 1/2 inch for lengths from 36 inches to 50 inches. d. 1% for lengths over 50 inches. TABLE IV. Size code and elbow fitting drop height. 1/ Dimensions (a), (b), (c) and (d) are depicted on figure 3. Maximum drop height of elbow fitting Size Reference tube OD Size code (a) 1/ (b) 1/ (c) 1/
25、(d) 1/ 8 0.500 H 0.485 0.850 0.458 0.92710 0.625 J 0.571 1.161 0.410 0.931 12 0.750 K 0.658 1.411 0.503 1.19116Z 1.000 M 0.695 1.535 0.540 1.317 20Z 1.250 N 0.803 1.817 0.604 1.53524Z 1.500 P 0.902 2.067 0.659 1.723 Source: http:/assist.daps.dla.mil - Downloaded: 2005-09-30T07:29ZCheck the source to
26、 verify that this is the current version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8002D w/AMENDMENT 1 6 NOTE: Angular alignment shall be measured in degrees with a tolerance of 2. FIGURE 2. Measurement of angular alignment between
27、 elbow fittings. NOTES: 1. Hose assembly length “L” shall be measured, with the hose laid out horizontally and straight between the center of the nipple end and the center of the flange sealing surface, along a straight line parallel to the hose length. 2. See table IV for dimensions of (a), (b), (c
28、) and (d). FIGURE 3. Elbow fitting drop height, dimensions (a), (b), (c) and (d). Source: http:/assist.daps.dla.mil - Downloaded: 2005-09-30T07:29ZCheck the source to verify that this is the current version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without licen
29、se from IHS-,-,-MS8002D w/AMENDMENT 1 7 PIN: The PIN for each hose assembly shall include its size code, length, style, protective sleeve type, and the angular alignment between the elbow fittings, as applicable. Example: The PIN for an 8.250 inch (209.55 mm) length, style F hose assembly with a .50
30、0 inch (12.70 mm) tube OD, a fire protective sleeve in accordance with SAE AS1072, and a 30 between the elbow fittings shall be as depicted below. 08 2 F AH Amendment notations. The margins of this specification are marked with vertical lines to indicate modifications generated by this amendment. Th
31、is was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations. MS8002 030Angular alig
32、nment between elbow fittings as A, B, C, G, H, K, M, N, T, and U. Protective sleeve type (see table III). Leave blank if not required. If a protective follows: MS8002H082F030. Style (see table I and figure 1). Length in eights of an inch. Length in inches. Specification number.Size code (see table I
33、V). Source: http:/assist.daps.dla.mil - Downloaded: 2005-09-30T07:29ZCheck the source to verify that this is the current version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHSsleeve is not required, the PIN shall be as specified on figure 2 (
34、leave blank for styles -,-,-MS8002D w/AMENDMENT 1 8 Referenced documents. In addition to MIL-DTL-25579, this document references the following: MIL-DTL-27267 MIL-DTL-27272 MS27057 MS27056 MS27058 MS27053 MS27059 MS27054 MS27060 MS27055 MS33786 SAE AS1072 SAE AS1073 SAE AS4395 SAE AS1291 SAE AS1298 C
35、ONCLUDING MATERIAL Custodians: Preparing activity:Army - AV DLA - CC Navy - AS Air Force - 99 (Project 4720-0429-000) DLA - CC Review activities: Army - AR, AT, EA, MI Navy - MC, SA, SH Air Force 70 NOTE: The activities listed above were interested in this document as of the date of this document. S
36、ince organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Source: http:/assist.daps.dla.mil - Downloaded: 2005-09-30T07:29ZCheck the source to verify that this is the current version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
