1、 MS8006C w/AMENDMENT 1 09 September 2005 SUPERSEDING MS8006C 4 September 2003 DETAIL SPECIFICATION SHEET HOSE ASSEMBLY, POLYTETRAFLUOROETHYLENE, PERMANENTLY ATTACHED FITTINGS, HIGH TEMPERATURE, MEDIUM PRESSURE, FLARELESS-TO-FLARELESS This specification is approved for use by all Departments and Agen
2、cies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-25579. Hose assembly dimensions for style A: See table l. TABLE I. Hose assembly dimensions for style A. 1/ Fitting ends Dimensions 2/ 3/ 1 2 Hose size
3、 A (nom) B ( max) C (max) F (max) 3/4 0.191 1.282 0.620 0.580 4 0.222 1.222 0.620 0.6545 0.235 1.340 0.680 0.726 6 0.230 1.469 0.750 0.798Straight Straight 8 0.310 1.640 0.880 1.014 10 0.356 1.940 0.967 1.15812 0.393 1.913 1.122 1.447 16Z 0.429 2.298 1.480 1.73620Z 0.393 2.577 1.750 2.328 24Z 0.398
4、2.800 2.150 2.621INCH-POUND1/ Style A uses class 1 fittings which are made from corrosion resistant steel (CRES). 2/ Dimensions are shown on figure 1. 3/ Apply NAS 1760 in accordance with MIL-DTL-25579/1, see requirements. FIGURE 1. Style A hose assembly. AMSC N/A FSC 4720 Source: http:/assist.daps.
5、dla.mil - Downloaded: 2005-10-05T07:15ZCheck the source to verify that this is the current version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8006C w/AMENDMENT 1 2 Hose assembly dimensions for style B: See table II. TABLE II. Hose a
6、ssembly dimensions for style B. 1/ Fitting ends Dimensions 2/ 3/ 1 2 Hose size A (nom) B (max)C (max)D (max)E (max)F (max)G (min) G (max) 3/4 0.191 1.282 0.620 1.240 0.950 0.580 0.412 0.537 4 0.222 1.222 0.620 1.490 0.970 0.654 0.404 0.5295 0.235 1.340 0.680 1.495 1.017 0.726 0.428 0.553 6 0.230 1.4
7、69 0.750 1.610 1.122 0.798 0.506 0.631Straight 45 8 0.310 1.640 0.880 1.722 1.426 1.014 0.542 0.789 10 0.356 1.940 0.967 2.037 1.596 1.158 0.631 0.877 12 0.393 1.913 1.122 2.368 1.739 1.447 0.631 0.952 16Z 0.429 2.298 1.480 2.583 1.931 1.736 0.741 1.069 20Z 0.393 2.577 1.750 2.946 2.084 2.328 0.863
8、1.196 24Z 0.398 2.800 2.150 3.210 2.376 2.621 1.012 1.402 1/ Style B uses class 1 fittings which are made from CRES. 2/ Dimensions are shown on figure 2. 3/ Apply NAS 1760 in accordance with MIL-DTL-25579/1, see requirements. FIGURE 2. Style B hose assembly. Source: http:/assist.daps.dla.mil - Downl
9、oaded: 2005-10-05T07:15ZCheck the source to verify that this is the current version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8006C w/AMENDMENT 1 3 Hose assembly dimensions for style C: Seed table III. TABLE III. Hose assembly dime
10、nsions for style C. 1/ 1/ Style C uses class 1 fittings which are made from CRES. Fitting ends Dimensions 2/ 3/ 1 2 Hose size A (nom) B (max) C (max) F (max) H (max) J (max) K (min) K (max)3/4 0.191 1.282 0.620 0.580 1.845 1.350 0.721 0.846 4 0.222 1.222 0.620 0.654 1.885 1.370 0.705 0.830 5 0.235 1
11、340 0.680 0.726 1.980 1.550 0.788 0.975 6 0.230 1.469 0.750 0.798 2.205 1.687 0.895 1.082 Straight 90 8 0.310 1.640 0.880 1.014 2.495 2.032 1.032 1.282 10 0.356 1.940 0.967 1.158 2.955 2.437 1.357 1.607 12 0.393 1.913 1.122 1.447 3.705 2.795 1.591 1.841 16Z 0.429 2.298 1.480 1.736 4.100 3.160 1.741
12、 1.991 20Z 0.393 2.577 1.750 2.328 4.835 3.664 2.021 2.396 24Z 0.398 2.800 2.150 2.621 5.480 4.251 2.403 2.778 2/ Dimensions are shown on figure 3. 3/ Apply NAS 1760 in accordance with MIL-DTL-25579/1, see requirements. FIGURE 3. Style C hose assembly. Source: http:/assist.daps.dla.mil - Downloaded:
13、 2005-10-05T07:15ZCheck the source to verify that this is the current version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8006C w/AMENDMENT 1 4 Hose assembly dimensions for style D: See table IV. TABLE IV. Hose assembly dimensions fo
14、r style D. 1/ 1/ Style D uses class 1 fittings which are made from CRES. Fitting ends Dimensions 2/ 3/ 1 2 Hose size A (nom) C (max) D (max) E (max) F (max) G (min) G (max) 3/4 0.191 0.620 1.240 0.950 0.580 0.412 0.537 4 0.222 0.620 1.490 0.970 0.654 0.404 0.529 5 0.235 0.680 1.495 1.017 0.726 0.428
15、 0.553 6 0.230 0.750 1.610 1.122 0.798 0.506 0.631 45 45 8 0.310 0.880 1.722 1.426 1.014 0.542 0.789 10 0.356 0.967 2.037 1.596 1.158 0.631 0.877 12 0.393 1.122 2.368 1.739 1.447 0.631 0.952 16Z 0.429 1.480 2.583 1.931 1.736 0.741 1.069 20Z 0.393 1.750 2.946 2.084 2.328 0.863 1.196 24Z 0.398 2.150 3
16、210 2.376 2.621 1.012 1.402 2/ Dimensions are shown on figure 4. 3/ Apply NAS 1760 in accordance with MIL-DTL-25579/1, see requirements. FIGURE 4. Style D hose assembly. Source: http:/assist.daps.dla.mil - Downloaded: 2005-10-05T07:15ZCheck the source to verify that this is the current version befo
17、re use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8006C w/AMENDMENT 1 5 Hose assembly dimensions for style E: See table V. TABLE V. Hose assembly dimensions for style E. 1/ 1/ Style E uses class 1 fittings which are made from CRES. Dimensions
18、2/ 3/ Fitting ends 1 2 Hose size A (nom) C (max) D (max)E (max)F (max)G (min) G (max)H (max) J (max) K (min) K (max)3/4 0.191 0.620 1.240 0.950 0.580 0.412 0.537 1.845 1.350 0.721 0.8464 0.222 0.620 1.490 0.970 0.654 1.404 0.529 1.885 1.370 0.705 0.8305 0.235 0.680 1.495 1.017 0.726 0.428 0.553 1.98
19、0 1.550 0.788 0.9756 0.230 0.750 1.610 1.122 0.798 0.506 0.631 2.205 1.687 0.895 1.08245 90 8 0.310 0.880 1.722 1.426 1.014 0.542 0.789 2.495 2.032 1.032 1.28210 0.356 0.967 2.037 1.596 1.158 0.631 0.877 2.955 2.437 1.357 1.60712 0.393 1.122 2.368 1.739 1.447 0.631 0.952 3.705 2.795 1.591 1.84116Z 0
20、429 1.480 2.583 1.931 1.736 0.741 1.069 4.100 3.160 1.741 1.99120Z 0.393 1.750 2.946 2.084 2.328 0.863 1.196 4.835 3.664 2.021 2.39624Z 0.398 2.150 3.210 2.376 2.621 1.012 1.402 5.480 4.251 2.403 2.7782/ Dimensions are shown on figure 5. 3/ Apply NAS 1760 in accordance with MIL-DTL-25579/1, see req
21、uirements. FIGURE 5. Style E hose assembly. Source: http:/assist.daps.dla.mil - Downloaded: 2005-10-05T07:15ZCheck the source to verify that this is the current version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8006C w/AMENDMENT 1
22、6 Hose assembly dimensions for style F: See table VI. TABLE VI. Hose assembly dimensions for style F. 1/ 1/ Style F uses class 1 fittings which are made from CRES. Fitting ends Dimensions 2/ 3/ 1 2 Hose size A (nom) C (max) F (max) H (max) J (max) K (min) K (max) 3/4 0.191 0.620 0.580 1.845 1.350 0.
23、721 0.846 4 0.222 0.620 0.654 1.885 1.370 0.705 0.830 5 0.235 0.680 0.726 1.980 1.550 0.788 0.975 6 0.230 0.750 0.798 2.205 1.687 0.895 1.082 90 90 8 0.310 0.880 1.014 2.495 2.032 1.032 1.282 10 0.356 0.967 1.158 2.955 2.437 1.357 1.607 12 0.393 1.122 1.447 3.705 2.795 1.591 1.841 16Z 0.429 1.480 1.
24、736 4.100 3.160 1.741 1.991 20Z 0.393 1.750 2.328 4.835 3.664 2.021 2.396 24Z 0.398 2.150 2.621 5.480 4.251 2.403 2.778 2/ Dimensions are shown on figure 6. 3/ Apply NAS 1760 in accordance with MIL-DTL-25579/1, see requirements. FIGURE 6. Style F hose assembly. Source: http:/assist.daps.dla.mil - Do
25、wnloaded: 2005-10-05T07:15ZCheck the source to verify that this is the current version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8006C w/AMENDMENT 1 7 Hose assembly dimensions for style G: See table VII. TABLE VII. Hose assembly di
26、mensions for style G. 1/ 1/ Style G uses class 2 fittings which are made from a combination of aluminum and CRES. Fitting ends Dimensions 2/ 3/ 1 2 Hose size A (nom) B ( max) C (max) F (max) 8 0.310 1.640 0.880 1.014 10 0.356 1.940 0.967 1.158Straight Straight 12 0.393 1.913 1.122 1.447 16Z 0.429 2.
27、298 1.480 1.73620Z 0.393 2.577 1.750 2.328 24Z 0.398 2.800 2.150 2.6212/ Dimensions are shown on figure 7. 3/ Apply NAS 1760 in accordance with MIL-DTL-25579/1, see requirements. FIGURE 7. Style G hose assembly. Source: http:/assist.daps.dla.mil - Downloaded: 2005-10-05T07:15ZCheck the source to ver
28、ify that this is the current version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8006C w/AMENDMENT 1 8 Hose assembly dimensions for style H: See table VIII. TABLE VIII. Hose assembly dimensions for style H. 1/ 1/ Style H uses class 2
29、 fittings which are made from a combination of aluminum and CRES. Fitting ends Dimensions 2/ 3/ 1 2 Hose size A (nom) B (max) C (max) D (max) E (max) F (max) G (min) G (max)8 0.310 1.640 0.880 1.722 1.426 1.014 0.542 0.789 10 0.356 1.940 0.967 2.037 1.596 1.158 0.631 0.877 Straight 45 12 0.393 1.913
30、 1.122 2.368 1.739 1.447 0.631 0.952 16Z 0.429 2.298 1.480 2.583 1.931 1.736 0.741 1.069 20Z 0.393 2.577 1.750 2.946 2.084 2.328 0.863 1.196 24Z 0.398 2.800 2.150 3.210 2.376 2.621 1.012 1.402 2/ Dimensions are shown on figure 8. 3/ Apply NAS 1760 in accordance with MIL-DTL-25579/1, see requirements
31、 FIGURE 8. Style H hose assembly. Source: http:/assist.daps.dla.mil - Downloaded: 2005-10-05T07:15ZCheck the source to verify that this is the current version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8006C w/AMENDMENT 1 9 Hose as
32、sembly dimensions for style J: See table IX. TABLE IX. Hose assembly dimensions for style J. 1/ 1/ Style J uses class 2 fittings which are made from a combination of aluminum and CRES. Fitting ends Dimensions 2/ 3/ 1 2 Hose size A (nom) B (max) C (max) F (max) H (max) J (max) K (min) K (max)8 0.310
33、1.640 0.880 1.014 2.495 2.032 1.032 1.282 10 0.356 1.940 0.967 1.158 2.955 2.437 1.357 1.607 Straight 90 12 0.393 1.913 1.122 1.447 3.705 2.795 1.591 1.841 16Z 0.429 2.298 1.480 1.736 4.100 3.160 1.741 1.991 20Z 0.393 2.577 1.750 2.328 4.835 3.664 2.021 2.396 24Z 0.398 2.800 2.150 2.621 5.480 4.251
34、2.403 2.778 2/ Dimensions are shown on figure 9. 3/ Apply NAS 1760 in accordance with MIL-DTL-25579/1, see requirements. FIGURE 9. Style J hose assembly. Source: http:/assist.daps.dla.mil - Downloaded: 2005-10-05T07:15ZCheck the source to verify that this is the current version before use.Provided b
35、y IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8006C w/AMENDMENT 1 10 Hose assembly dimensions for style K: See table X. TABLE X. Hose assembly dimensions for style K. 1/ 1/ Style K uses class 2 fittings which are made from a combination of aluminum and CRE
36、S. Fitting ends Dimensions 2/ 3/ 1 2 Hose size A (nom) C (max) D (max) E (max) F (max) G (min) G (max) 8 0.310 0.880 1.722 1.426 1.014 0.542 0.789 10 0.356 0.967 2.037 1.596 1.158 0.631 0.877 45 45 12 0.393 1.122 2.368 1.739 1.447 0.631 0.952 16Z 0.429 1.480 2.583 1.931 1.736 0.741 1.069 20Z 0.393 1
37、750 2.946 2.084 2.328 0.863 1.196 24Z 0.398 2.150 3.210 2.376 2.621 1.012 1.402 2/ Dimensions are shown on figure 10. 3/ Apply NAS 1760 in accordance with MIL-DTL-25579/1, see requirements. FIGURE 10. Style K hose assembly. Source: http:/assist.daps.dla.mil - Downloaded: 2005-10-05T07:15ZCheck the
38、source to verify that this is the current version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8006C w/AMENDMENT 1 11 Hose assembly dimensions for style M: See table XI. TABLE XI. Hose assembly dimensions for style M. 1/ 1/ Style M us
39、es class 2 fittings which are made from a combination of aluminum and CRES. Dimensions 2/ 3/ Fitting ends 1 2 Hose size A (nom) C (max) D (max)E (max)F (max)G (min) G (max)H (max) J (max) K (min) K (max)8 0.310 0.880 1.722 1.426 1.014 0.542 0.789 2.495 2.032 1.032 1.28210 0.356 0.967 2.037 1.596 1.1
40、58 0.631 0.877 2.955 2.437 1.357 1.60745 90 12 0.393 1.122 2.368 1.739 1.447 0.631 0.952 3.705 2.795 1.591 1.84116Z 0.429 1.480 2.583 1.931 1.736 0.741 1.069 4.100 3.160 1.741 1.99120Z 0.393 1.750 2.946 2.084 2.328 0.863 1.196 4.835 3.664 2.021 2.39624Z 0.398 2.150 3.210 2.376 2.621 1.012 1.402 5.48
41、0 4.251 2.403 2.7782/ Dimensions are shown on figure 11. 3/ Apply NAS 1760 in accordance with MIL-DTL-25579/1, see requirements. FIGURE 11. Style M hose assembly. Source: http:/assist.daps.dla.mil - Downloaded: 2005-10-05T07:15ZCheck the source to verify that this is the current version before use.P
42、rovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8006C w/AMENDMENT 1 12 Hose assembly dimensions for style N: See table XII. TABLE XII. Hose assembly dimensions for style N. 1/ 1/ Style N uses class 2 fittings which are made from a combination of alu
43、minum and CRES. Fitting ends Dimensions 2/ 3/ 1 2 Hose size A (nom) C (max) F (max) H (max) J (max) K (min) K (max) 8 0.310 0.880 1.014 2.495 2.032 1.032 1.282 10 0.356 0.967 1.158 2.955 2.437 1.357 1.607 90 90 12 0.393 1.122 1.447 3.705 2.795 1.591 1.841 16Z 0.429 1.480 1.736 4.100 3.160 1.741 1.99
44、1 20Z 0.393 1.750 2.328 4.835 3.664 2.021 2.396 24Z 0.398 2.150 2.621 5.480 4.251 2.403 2.778 2/ Dimensions are shown on figure 12. 3/ Apply NAS 1760 in accordance with MIL-DTL-25579/1, see requirements. FIGURE 12. Style N hose assembly. Source: http:/assist.daps.dla.mil - Downloaded: 2005-10-05T07:
45、15ZCheck the source to verify that this is the current version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8006C w/AMENDMENT 1 13 Protective sleeve code: See table XIII. TABLE XIII. Protective sleeve code. Code TypeA SAE AS1072 sleev
46、e, fire protection, silicone covered, temperature ranging from -65F to 450F, and intermittently to 500F, secured with CRES bands as required. 1/ B SAE AS1073 - code B sleeve, abrasion protection, heat shrinkable, black polyolefin, temperature ranging from -65F to 250F. C SAE AS1291 - code A sleeve,
47、chafe guard, extruded seamless white PTFE, temperature ranging from -65F to 450F, secured with CRES bands as required. D SAE AS1291 - code C sleeve, chafe guard, extruded seamless transparent FEP, temperature ranging from -65F to 350F, secured with CRES bands as required. E SAE AS1298 sleeve, heavy
48、wall chafe guard, extruded seamless black PTFE, temperature ranging from -65F to 450F, secured with CRES bands as required. L Lock-wire hole F Code A + L G Code B + L H Code C + L J Code D + L K Code E + L 1/ To prevent wicking of fluids, the cut end of the fire protective sleeve (code A) shall be coated with Room Temperature Vulcanized (RTV) silicone rubber prior to installation. After installation, cracks and voids in the fire protective sleeve shall be coated with RTV rubber to prevent expo
