1、 MS8008C w/AMENDMENT 1 09 September 2005 SUPERSEDING MS8008C 24 September 2003 DETAIL SPECIFICATION SHEET HOSE ASSEMBLY, POLYTETRAFLUOROETHYLENE, PERMANENTLY ATTACHED FITTINGS, HIGH TEMPERATURE, MEDIUM PRESSURE, FLARELESS-TO-FLANGE This specification is approved for use by all Departments and Agenci
2、es of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-25579. Hose assembly dimensions for style A: See table l. TABLE I. Hose assembly dimensions for style A. 1/ Fitting ends Dimensions 2/ 3/ 4/ 5/ 1 2 Hose
3、size A (nom) B ( max) C (max) F (max) M (max) P (max) 8 0.310 1.640 0.880 1.014 1.560 0.875 10 0.356 1.940 0.967 1.158 1.570 1.000 Straight Straight 12 0.393 1.913 1.122 1.447 1.640 1.250 16Z 0.429 2.298 1.480 1.736 1.750 1.500 20Z 0.393 2.577 1.750 2.328 1.990 1.844 24Z 0.398 2.800 2.150 2.621 2.26
4、0 2.125 INCH-POUND1/ Style A uses class 1 fittings which are made from corrosion resistant steel (CRES). 2/ Dimensions are shown on figure 1. 3/ Dimensions “A” and “B” are based on end of MS8000 series seal. 4/ Assembly length (see PIN) is based on end of MS8000 series seal to face of flange. 5/ App
5、ly NAS 1760 in accordance with MIL-DTL-25579/1, see requirements. FIGURE 1. Style A hose assembly. AMSC N/A FSC 4720 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8008C w/AMENDMENT 1 2 Hose assembly dimensions for style B: See table lI. TABLE II.
6、 Hose assembly dimensions for style B. 1/ 1/ Style B uses class 1 fittings which are made from CRES. 2/ Dimensions are shown on figure 2. 3/ Dimensions “A” and “B” are based on end of MS8000 series seal. 4/ Assembly length (see PIN) is based on end of MS8000 series seal to face of flange. 5/ Apply N
7、AS 1760 in accordance with MIL-DTL-25579/1, see requirements. FIGURE 2. Style B hose assembly. Hose assembly dimensions for style C: See table lII. TABLE III. Hose assembly dimensions for style C. 1/ 1/ Style C uses class 1 fittings which are made from CRES. Fitting ends Dimensions 2/ 3/ 4/ 5/ 1 2 H
8、ose size A (nom) B (max) C (max) D (max) F (max) N (max) P (max) R (min) R (max)8 0.310 1.640 0.880 1.722 1.014 0.606 0.875 0.303 0.428 10 0.356 1.940 0.967 2.037 1.158 0.658 1.000 0.340 0.465 Straight 45 12 0.393 1.913 1.122 2.368 1.447 0.789 1.250 0.433 0.558 16Z 0.429 2.298 1.480 2.583 1.736 0.92
9、9 1.500 0.470 0.657 20Z 0.393 2.577 1.750 2.946 2.328 1.020 1.844 0.534 0.721 24Z 0.398 2.800 2.150 3.210 2.621 1.186 2.125 0.589 0.839 Fitting ends Dimensions 2/ 3/ 4/ 5/ 1 2 Hose size A (nom) B (max) C (max) F (max) P (max) S (max) T (max) U (min) U (max)8 0.310 1.640 0.880 1.014 0.875 2.320 1.422
10、 0.857 0.982 10 0.356 1.940 0.967 1.158 1.000 2.875 1.499 0.861 1.015 Straight 90 12 0.393 1.913 1.122 1.447 1.250 3.606 1.807 1.032 1.246 16Z 0.429 2.298 1.480 1.736 1.500 3.981 2.174 1.156 1.434 20Z 0.393 2.577 1.750 2.328 1.844 4.435 2.590 1.344 1.715 24Z 0.398 2.800 2.150 2.621 2.125 5.075 3.103
11、 1.516 2.028 2/ Dimensions are shown on figure 3. 3/ Dimensions “A” and “B” are based on end of MS8000 series seal. 4/ Assembly length (see PIN) is based on end of MS8000 series seal to face of flange. 5/ Apply NAS 1760 in accordance with MIL-DTL-25579/1, see requirements. Provided by IHSNot for Res
12、aleNo reproduction or networking permitted without license from IHS-,-,-MS8008C w/AMENDMENT 1 3 FIGURE 3. Style C hose assembly. Hose assembly dimensions for style D: See table lV. TABLE IV. Hose assembly dimensions for style D. 1/ 1/ Style D uses class 1 fittings which are made from CRES. Dimension
13、s 2/ 3/ 4/ 5/ Fitting ends 1 2 Hose size A (nom) C (max) D (max) E (max) F (max)G (min) G (max)N (max)P (max) R (min) R (max)8 0.310 0.880 1.722 1.426 1.014 0.542 0.789 0.606 0.875 0.303 0.42810 0.356 0.967 2.037 1.596 1.158 0.631 0.877 0.658 1.000 0.340 0.46545 45 12 0.393 1.122 2.368 1.739 1.447 0
14、.631 0.952 0.789 1.250 0.433 0.55816Z 0.429 1.480 2.583 1.931 1.736 0.741 1.069 0.929 1.500 0.470 0.65720Z 0.393 1.750 2.946 2.084 2.328 0.863 1.196 1.020 1.844 0.534 0.72124Z 0.398 2.150 3.210 2.376 2.621 1.012 1.376 1.186 2.125 0.589 0.8392/ Dimensions are shown on figure 4. 3/ Dimensions “A” is b
15、ased on end of MS8000 series seal. 4/ Assembly length (see PIN) is based on end of MS8000 series seal to face of flange. 5/ Apply NAS 1760 in accordance with MIL-DTL-25579/1, see requirements. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8008C w
16、/AMENDMENT 1 4 FIGURE 4. Style D hose assembly. Hose assembly dimensions for style E: See table V. TABLE V. Hose assembly dimensions for style E. 1/ 1/ Style E uses class 1 fittings which are made from CRES. Dimensions 2/ 3/ 4/ 5/ Fitting ends 1 2 Hose size A (nom) C (max) D (max) E (max)F (max) G (
17、min)G (max)P (max)S (max) T (max) U (min)U (max)8 0.310 0.880 1.722 1.426 1.014 0.542 0.789 0.875 2.320 1.422 0.857 0.98210 0.356 0.967 2.037 1.596 1.158 0.631 0.877 1.000 2.875 1.499 0.861 1.01545 90 12 0.393 1.122 2.368 1.739 1.447 0.631 0.952 1.250 3.606 1.807 1.032 1.24616Z 0.429 1.480 2.583 1.9
18、31 1.736 0.741 1.069 1.500 3.981 2.174 1.156 1.43420Z 0.393 1.750 2.946 2.084 2.328 0.863 1.196 1.844 4.435 2.590 1.344 1.71524Z 0.398 2.150 3.210 2.376 2.621 1.012 1.376 2.125 5.075 3.103 1.516 2.0282/ Dimensions are shown on figure 5. 3/ Dimensions “A” is based on end of MS8000 series seal. 4/ Ass
19、embly length (see PIN) is based on end of MS8000 series seal to face of flange. 5/ Apply NAS 1760 in accordance with MIL-DTL-25579/1, see requirements. FIGURE 5. Style E hose assembly. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8008C w/AMENDME
20、NT 1 5 Hose assembly dimensions for style F: See table Vl. TABLE VI. Hose assembly dimensions for style F. 1/ 1/ Style F uses class 1 fittings which are made from CRES. Dimensions 2/ 3/ 4/ 5/ Fitting ends 1 2 Hose size A (nom) C (max) F (max) H (max)J (max)K (min)K (max)P (max)S (max) T (max) U (min
21、)U (max)8 0.310 0.880 1.014 2.495 2.032 1.032 1.282 0.875 2.320 1.422 0.857 0.98210 0.356 0.967 1.158 2.955 2.437 1.357 1.607 1.000 2.875 1.499 0.861 1.01590 90 12 0.393 1.122 1.447 3.705 2.795 1.591 1.841 1.250 3.606 1.807 1.032 1.24616Z 0.429 1.480 1.736 4.100 3.160 1.741 1.991 1.500 3.981 2.174 1
22、.156 1.43420Z 0.393 1.750 2.328 4.835 3.664 2.021 2.396 1.844 4.435 2.590 1.344 1.71524Z 0.398 2.150 2.621 5.480 4.251 2.403 2.778 2.125 5.075 3.103 1.516 2.0282/ Dimensions are shown on figure 6. 3/ Dimensions “A” is based on end of MS8000 series seal. 4/ Assembly length (see PIN) is based on end o
23、f MS8000 series seal to face of flange. 5/ Apply NAS 1760 in accordance with MIL-DTL-25579/1, see requirements. FIGURE 6. Style F hose assembly. Hose assembly dimensions for style G: See table VIl. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS80
24、08C w/AMENDMENT 1 6 TABLE VII. Hose assembly dimensions for style G. 1/ Fitting ends Dimensions 2/ 3/ 4/ 5/ 1 2 Hose size A (nom) C (max) D (max) E (max) F (max) G (min) G (max) M (max) P (max)8 0.310 0.880 1.722 1.426 1.014 0.542 0.789 1.560 0.875 10 0.356 0.967 2.037 1.596 1.158 0.631 0.877 1.570
25、1.000 45 Straight 12 0.393 1.122 2.368 1.739 1.447 0.631 0.952 1.640 1.250 16Z 0.429 1.480 2.583 1.931 1.736 0.741 1.069 1.750 1.500 20Z 0.393 1.750 2.946 2.084 2.328 0.863 1.196 1.990 1.844 24Z 0.398 2.150 3.210 2.376 2.621 1.012 1.376 2.260 2.125 1/ Style G uses class 1 fittings which are made fro
26、m CRES. 2/ Dimensions are shown on figure 7. 3/ Dimensions “A” is based on end of MS8000 series seal. 4/ Assembly length (see PIN) is based on end of MS8000 series seal to face of flange. 5/ Apply NAS 1760 in accordance with MIL-DTL-25579/1, see requirements. FIGURE 7. Style G hose assembly. Hose as
27、sembly dimensions for style H: See table VIIl. TABLE VIII. Hose assembly dimensions for style H. 1/ 1/ Style H uses class 1 fittings which are made from CRES. Fitting ends Dimensions 2/ 3/ 4/ 5/ 1 2 Hose size A (nom) C (max) F (max) H (max) J (max) K (min) K (max) M (max) P (max)8 0.310 0.880 1.014
28、2.495 2.032 1.032 1.282 1.560 0.875 10 0.356 0.967 1.158 2.955 2.437 1.357 1.607 1.570 1.000 90 Straight 12 0.393 1.122 1.447 3.705 2.795 1.591 1.841 1.640 1.250 16Z 0.429 1.480 1.736 4.100 3.160 1.741 1.991 1.750 1.500 20Z 0.393 1.750 2.328 4.835 3.664 2.021 2.396 1.990 1.844 24Z 0.398 2.150 2.621
29、5.480 4.251 2.403 2.778 2.260 2.125 2/ Dimensions are shown on figure 8. 3/ Dimensions “A” is based on end of MS8000 series seal. 4/ Assembly length (see PIN) is based on end of MS8000 series seal to face of flange. 5/ Apply NAS 1760 in accordance with MIL-DTL-25579/1, see requirements. Provided by
30、IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8008C w/AMENDMENT 1 7 FIGURE 8. Style H hose assembly. Hose assembly dimensions for style J: See table lX. TABLE IX. Hose assembly dimensions for style J. 1/ 1/ Style J uses class 1 fittings which are made from C
31、RES. Dimensions 2/ 3/ 4/ 5/ Fitting ends 1 2 Hose size A (nom) C (max) D (max) F (max)H (max)J (max)K (min)K (max)N (max) P (max) R (min)R (max)8 0.310 0.880 1.722 1.014 2.495 2.032 1.032 1.282 0.606 0.875 0.303 0.42810 0.356 0.967 2.037 1.158 2.955 2.437 1.357 1.607 0.658 1.000 0.340 0.46590 45 12
32、0.393 1.122 2.368 1.447 3.705 2.795 1.591 1.841 0.789 1.250 0.433 0.55816Z 0.429 1.480 2.583 1.736 4.100 3.160 1.741 1.991 0.929 1.500 0.470 0.65720Z 0.393 1.750 2.946 2.328 4.835 3.664 2.021 2.396 1.020 1.844 0.534 0.72124Z 0.398 2.150 3.210 2.621 5.480 4.251 2.403 2.778 1.186 2.125 0.589 0.8392/ D
33、imensions are shown on figure 9. 3/ Dimensions “A” is based on end of MS8000 series seal. 4/ Assembly length (see PIN) is based on end of MS8000 series seal to face of flange. 5/ Apply NAS 1760 in accordance with MIL-DTL-25579/1, see requirements. Provided by IHSNot for ResaleNo reproduction or netw
34、orking permitted without license from IHS-,-,-MS8008C w/AMENDMENT 1 8 FIGURE 9. Style J hose assembly. Hose assembly dimensions for style K: See table X. TABLE X. Hose assembly dimensions for style K. 1/ 1/ Style K uses class 2 fittings which are made from a combination of aluminum and CRES. Fitting
35、 ends Dimensions 2/ 3/ 4/ 5/ 1 2 Hose size A (nom) B ( max) C (max) F (max) M (max) P (max) 8 0.310 1.640 0.880 1.014 1.560 0.875 10 0.356 1.940 0.967 1.158 1.570 1.000Straight Straight 12 0.393 1.913 1.122 1.447 1.640 1.250 16Z 0.429 2.298 1.480 1.736 1.750 1.50020Z 0.393 2.577 1.750 2.328 1.990 1.
36、844 24Z 0.398 2.800 2.150 2.621 2.260 2.1252/ Dimensions are shown on figure 10. 3/ Dimensions “A” and “B” are based on end of MS8000 series seal. 4/ Assembly length (see PIN) is based on end of MS8000 series seal to face of flange. 5/ Apply NAS 1760 in accordance with MIL-DTL-25579/1, see requireme
37、nts. FIGURE 10. Style K hose assembly. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8008C w/AMENDMENT 1 9 Hose assembly dimensions for style M: See table Xl. TABLE XI. Hose assembly dimensions for style M. 1/ 1/ Style M uses class 2 fittings whi
38、ch are made from a combination of aluminum and CRES. 2/ Dimensions are shown on figure 11. 3/ Dimensions “A” and “B” are based on end of MS8000 series seal. 4/ Assembly length (see PIN) is based on end of MS8000 series seal to face of flange. 5/ Apply NAS 1760 in accordance with MIL-DTL-25579/1, see
39、 requirements. FIGURE 11. Style M hose assembly. Hose assembly dimensions for style N: See table XIl. TABLE XII. Hose assembly dimensions for style N. 1/ 1/ Style N uses class 2 fittings which are made from a combination of aluminum and CRES. Fitting ends Dimensions 2/ 3/ 4/ 5/ 1 2 Hose size A (nom)
40、 B (max) C (max) D (max) F (max) N (max) P (max) R (min) R (max) 8 0.310 1.640 0.880 1.722 1.014 0.606 0.875 0.303 0.428 10 0.356 1.940 0.967 2.037 1.158 0.658 1.000 0.340 0.465 Straight 45 12 0.393 1.913 1.122 2.368 1.447 0.789 1.250 0.433 0.558 16Z 0.429 2.298 1.480 2.583 1.736 0.929 1.500 0.470 0
41、.657 20Z 0.393 2.577 1.750 2.946 2.328 1.020 1.844 0.534 0.721 24Z 0.398 2.800 2.150 3.210 2.621 1.186 2.125 0.589 0.839 Fitting ends Dimensions 2/ 3/ 4/ 5/ 1 2 Hose size A (nom) B (max) C (max) F (max) P (max) S (max) T (max) U (min) U (max) 8 0.310 1.640 0.880 1.014 0.875 2.320 1.422 0.857 0.982 1
42、0 0.356 1.940 0.967 1.158 1.000 2.875 1.499 0.861 1.015 Straight 90 12 0.393 1.913 1.122 1.447 1.250 3.606 1.807 1.032 1.246 16Z 0.429 2.298 1.480 1.736 1.500 3.981 2.174 1.156 1.434 20Z 0.393 2.577 1.750 2.328 1.844 4.435 2.590 1.344 1.715 24Z 0.398 2.800 2.150 2.621 2.125 5.075 3.103 1.516 2.028 2
43、/ Dimensions are shown on figure 12. 3/ Dimensions “A” and “B” are based on end of MS8000 series seal. 4/ Assembly length (see PIN) is based on end of MS8000 series seal to face of flange. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8008C w/AME
44、NDMENT 1 10 5/ Apply NAS 1760 in accordance with MIL-DTL-25579/1, see requirements. FIGURE 12. Style N hose assembly. Hose assembly dimensions for style P: See table XIIl. TABLE XIII. Hose assembly dimensions for style P. 1/ 1/ Style P uses class 2 fittings which are made from a combination of alumi
45、num and CRES. Dimensions 2/ 3/ 4/ 5/ Fitting ends 1 2 Hose size A (nom) C (max) D (max)E (max)F (max)G (min)G (max)N (max)P (max) R (min) R (max)8 0.310 0.880 1.722 1.426 1.014 0.542 0.789 0.606 0.875 0.303 0.42810 0.356 0.967 2.037 1.596 1.158 0.631 0.877 0.658 1.000 0.340 0.46545 45 12 0.393 1.122
46、 2.368 1.739 1.447 0.631 0.952 0.789 1.250 0.433 0.55816Z 0.429 1.480 2.583 1.931 1.736 0.741 1.069 0.929 1.500 0.470 0.65720Z 0.393 1.750 2.946 2.084 2.328 0.863 1.196 1.020 1.844 0.534 0.72124Z 0.398 2.150 3.210 2.376 2.621 1.012 1.376 1.186 2.125 0.589 0.8392/ Dimensions are shown on figure 13. 3
47、/ Dimensions “A” is based on end of MS8000 series seal. 4/ Assembly length (see PIN) is based on end of MS8000 series seal to face of flange. 5/ Apply NAS 1760 in accordance with MIL-DTL-25579/1, see requirements. Provided by IHSNot for ResaleNo reproduction or networking permitted without license f
48、rom IHS-,-,-MS8008C w/AMENDMENT 1 11 FIGURE 13. Style P hose assembly. Hose assembly dimensions for style R: See table XlV. TABLE XIV. Hose assembly dimensions for style R. 1/ 1/ Style S uses class 2 fittings which are made from a combination of aluminum and CRES. Dimensions 2/ 3/ 4/ 5/ Fitting ends
49、 1 2 Hose size A (nom) C (max) F (max) H (max)J (max)K (min)K (max)P (max)S (max) T (max) U (min)U (max)8 0.310 0.880 1.014 2.495 2.032 1.032 1.282 0.875 2.320 1.422 0.857 0.98210 0.356 0.967 1.158 2.955 2.437 1.357 1.607 1.000 2.875 1.499 0.861 1.01590 90 12 0.393 1.122 1.447 3.705 2.795 1.591 1.841 1.250 3.606 1.807 1.032 1.24616Z 0.429 1.480 1.736 4.100
