1、 MS9314C 16 February 2010 SUPERSEDING MS9314B (ASG) 20 December 1966 DETAIL SPECIFICATION SHEET CAP ASSEMBLY, TUBE - SAE-AMS5646 This specification is approved for use by all Departments and Agencies of the Department of Defense . The requirements for acquiring the product described herein shall con
2、sist of this specification sheet. FIGURE 1. Cap assembly, tube. AMSC N/A FSC 4730INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS9314C 2 Dash number Tube OD (reference) inches (mm) Nut Cap A minimum inches (mm) Approx weight lb/100 (kg/1
3、00) -02 .125 (3.18) MS9198-02 MS9313-02 .200 (5.08) 1.58 (0.7) -03 .188 (4.78) MS9198-03 MS9313-03 .260 (6.60) 2.11 (1.0) -04 .250 (6.35) MS9198-04 MS9313-04 .325 (8.26) 2.83 (1.3) -05 .313 (7.95) MS9198-05 MS9313-05 .395 (10.03) 4.04 (1.8) -06 .375 (9.53) MS9198-06 MS9313-06 .460 (11.68) 4.59 (2.1)
4、 -07 .438 (11.13) MS9198-07 MS9313-07 .520 (13.21) 5.60 (2.5) -08 .500 (12.70) MS9198-08 MS9313-08 .590 (14.99) 7.95 (3.6) -09 .562 (14.27) MS9198-09 MS9313-09 .655 (16.64) 9.13 (4.1) -10 .625 (15.88) MS9198-10 MS9313-10 .720 (18.29) 10.67 (4.8) -11 .688 (17.48) MS9198-11 MS9313-11 .790 (20.07) 13.5
5、3 (6.1) -12 .750 (19.05) MS9198-12 MS9313-12 .855 (21.72) 16.30 (7.4) -14 .875 (22.23) MS9198-14 MS9313-14 .980 (24.89) 20.25 (9.2) -16 1.000 (25.40) MS9198-16 MS9313-16 1.110 (28.19) 23.56 (10.7) -18 1.125 (28.58) MS9198-18 MS9313-18 1.235 (31.37) 33.74 (15.3) -20 1.250 (31.75) MS9198-20 MS9313-20
6、1.365 (34.67) 37.02 (16.8) -24 1.500 (38.10) MS9198-24 MS9313-24 1.635 (41.53) 51.51 (23.4) -28 1.750 (44.45) MS9198-28 MS9313-28 1.910 (48.51) 76.61 (34.7) -32 2.000 (50.80) MS9198-32 MS9313-32 2.185 (55.50) 91.65 (41.6) -40 2.500 (63.50) MS9198-40 MS9313-40 2.685 (68.20) 118.37 (53.7) -48 3.000 (7
7、6.20) MS9198-48 MS9313-48 3.200 (81.28) 153.98 (69.8) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Assembly shall be free of all burrs and slivers. 4. Do not support cap on seat during staking or marking of PIN. 5. Caps shall be free from defects (crac
8、ks, etc.) as a result of staking. 6. Nut shall spin freely on cap after staking. 7. Minimum push-out force 10 pounds (4.5 kg). 8. For design features purposes, this standard takes precedence over documents referenced herein. FIGURE 1. Cap assembly, tube - Continued. Provided by IHSNot for ResaleNo r
9、eproduction or networking permitted without license from IHS-,-,-MS9314C 3 REQUIREMENTS: Dimensions and configurations: See figure 1. Material: Steel, corrosion and heat-resistant in accordance with SAE-AMS5646. PIN: MS9314 -08 PIN Example: MS9314-08 identifies a cap assembly, tube .500 inch (tube),
10、 CRES. Do not use unassigned PINs. Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents. This document references the following: MS9313 MS9198 SAE-AS478 SAE-AMS5646
11、CONCLUDING MATERIAL Custodians: Preparing activity: Navy - AS DLA - CC Air Force - 99 DLA CC (Project 4730-2009-086) Review activity: Air Force - 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Specification sheet number Cap assembly size (see figure 1) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
