1、 DETAIL SPECIFICATION SHEET COVER, PROTECTIVE, ELECTRICAL CONNECTOR, RECEPTACLE This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-22992
2、. FIGURE 1. Dimensions and configuration. AMSC N/A FSC 5935 MS17349F 12 March 2013 SUPERSEDING MS17349E 7 March 2007 INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS17349F 2 Cover size Type A Thread class 2B L max Q D max E min F clearan
3、ce (see note 4) G min 12 A 0.8750-0.1P-0.2L-DS .765 5.00 1.094 .83 1.016 12 B 6 14 A 1.0000-0.1P-0.2L-DS 1.219 .87 1.141 14 B 6 16 A 1.1250-0.1P-0.2L-DS .980 1.344 .97 1.266 16 B 6 18 A 1.2500-0.1P-0.2L-DS 1.469 1.01 1.391 18 B 8 20 A 1.3750-0.1P-0.2L-DS 1.562 1.12 1.516 20 B 8 22 A 1.5000-0.1P-0.2L
4、-DS 6.00 1.688 1.19 1.641 22 B 8 24 A 1.7500-0.1P-0.2L-DS 1.938 1.33 1.891 24 B 8 28 A 2.0000-0.1P-0.2L-DS 2.219 1.48 2.141 28 B 8 32 A 2.2500-0.1P-0.2L-DS 2.469 1.62 2.391 32 B 10 36 A 2.5000-0.1P-0.2L-DS 2.719 1.77 2.641 36 B 10 40 A 2.7500-0.1P-0.2L-DS 2.969 1.91 2.891 40 B 10 44 A 3.0000-0.1P-0.
5、2L-DS 3.219 2.05 3.141 44 B 10 FIGURE 1. Dimensions and configuration - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS17349F 3 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwis
6、e specified, tolerances are .016 (0.41 mm). 4. F clearance to accommodate screw size indicated. FIGURE 1. Dimensions and configuration - Continued. Inches mm Inches mm Inches mm .765 .830 .870 .875 .970 .980 1.000 1.010 1.016 1.094 1.120 1.125 1.141 1.190 1.219 1.250 1.266 19.43 21.10 22.10 22.225 2
7、4.64 24.89 25.40 25.70 25.81 27.79 28.45 28.575 28.98 30.23 30.96 31.75 32.16 1.330 1.344 1.375 1.391 1.469 1.480 1.500 1.516 1.562 1.620 1.641 1.688 1.750 1.770 1.891 1.910 1.938 33.80 34.14 34.925 35.33 37.31 37.60 38.10 38.51 39.67 41.15 41.68 42.86 44.45 45.00 48.03 48.50 49.22 2.000 2.050 2.141
8、 2.219 2.250 2.391 2.469 2.500 2.641 2.719 2.750 2.891 2.969 3.000 3.149 3.219 5.000 6.000 50.80 52.07 54.38 56.36 57.15 60.73 62.71 63.50 67.08 69.06 69.85 73.43 75.41 76.20 79.98 81.76 127.00 152.40 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-M
9、S17349F 4 REQUIREMENTS: Design and construction: See figure 1. Cover type shall be designated as A or B. Type A is used for MS17345, MS17347 and MS17348, and type B is used for MS17343 and MS17346. Chain shall be passivated stainless steel in accordance with type II, class 3, trade number 8 as speci
10、fied in RR-C-271 and shall be within one link of length specified. Chain shall move freely on protective cap after assembly. Cover finish shall be in accordance with MIL-DTL-22992. Cover shall be marked with the Part or Identifying Number (PIN) only when procured as a separate part. PIN example: MS1
11、7349 C 28 A MS number Finish Cover size Type (A or B) Qualification: Visual and mechanical examination. Magnetic permeability. Water immersion. Salt spray (corrosion). Tensile. Air leakage. Group A sampling plan: Lot and sample sizes shall be as specified in table I. Samples shall be randomly select
12、ed from the lot. If one or more defects are found, the lot shall be rescreened and defects removed. A new sample as specified in table I shall then be randomly selected. If one or more defects are found in the second sample lot, the lot shall not be supplied to this specification. TABLE I. Group A s
13、ampling plan. Lot size Sample size 1 to 13 100 percent 14 to 150 13 units 151 to 280 20 units 281 to 500 29 units 501 to 1,200 34 units 1,201 to 3.200 42 units Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS17349F 5 Changes from previous issue. Ma
14、rginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents. In addition to MIL-DTL-22992, this document references the following: MS17343 MS17345 MS17346 MS17347 MS17348 RR-C-271 CONCLUDING MATERIAL Cus
15、todians: Preparing activity: Army CR DLA CC Navy EC Air Force 85 DLA CC Review activities: (Project 59352012-188) Army AR, CR4, MI Navy AS, CG, MC, OS Air Force 19 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
