1、AMSC N/A FSC 1640 INCH-POUND MS21260N 19 September 2011 SUPERSEDING MS21260M 5 November 2001 DETAIL SPECIFICATION SHEET TERMINAL, WIRE ROPE, SWAGING, STUD This specification sheet is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the pro
2、duct described herein shall consist of this specification sheet, MIL-DTL-781, and QPL-781. FIGURE 1. Terminal, wire rope, swaging, stud. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS21260N 2 NOTES: (a) Reference dimensions are for design purpose
3、s only and are not an inspection requirement. (b) Swaged terminals shall conform to As for length X. FIGURE 2. Terminal, wire rope, swaging, stud after swaging. TABLE I. Dash numbers and dimensions. Dash number Wire rope diameter Minimum breaking strength lb 1/ Thread B UN-3A UNF-3A A As Nominal ref
4、erence Minimum RH thread LH thread L2RH L2LH 1/16 0.062 480 0.1380 (# 6)-40 0.160 +0.000 -0.005 0.138 +0.000 -0.005 S2RH S2LH L3RH L3LH 3/32 0.093 920 0.1900 (#10)-32 0.218 0.190 S3RH S3LH L4RH L4LH 1/8 0.125 2000 0.2500 (1/4)-28 0.250 0.219 S4RH S4LH L5RH L5LH 5/32 0.156 2800 0.297 0.250 S5RH S5LH
5、L6RH L6LH 3/16 0.187 4200 0.3125 (5/16)-24 0.359 0.313 S6RH S6LH -7RH -7LH 7/32 0.218 5600 0.3750 (3/8)-24 0.427 0.375 +0.000 -0.007 -8RH -8LH 1/4 0.250 7000 0.494 0.438 -9RH -9LH 9/32 0.281 8000 0.4375 (7/16)-20 0.563 0.500 +0.000 -0.008 -10RH -10LH 5/16 0.312 9800 0.5000 (1/2)-20 0.635 0.563 -12RH
6、 -12LH 3/8 0.375 14400 0.5625 (9/16)-18 0.703 0.625 -14RH -14LH 7/16 0.437 17600 0.6250 (5/8)-18 0.781 0.688 -16RH -16LH 1/2 0.500 22800 0.6250 (5/8)-18 0.844 0.750 +0.000 -0.009 -18RH -18LH 9/16 0.562 28500 0.7500 (3/4)-16 0.984 0.875 -20RH -20LH 5/8 0.625 35000 0.8750 (7/8)-14 1.109 1.000 +0.000 -
7、0.010 -24RH -24LH 3/4 0.750 49600 1.0000 (1)-12 1.359 1.250 +0.000 -0.012 -28RH -28LH 7/8 0.875 66500 1.1250 (1 1/8)-12 1.593 +0.000 -0.010 1.437 -32RH -32LH 1 1.000 85400 1.2500 (1 1/4)-12 1.812 1.625 1/ To achieve the minimum breaking strength, for the terminal test only, a galvanized carbon steel
8、 wire rope shall be used. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS21260N 3 TABLE I. Dash numbers and dimensions - Continued. Dash number B1C +.006 -.000 D E F G H RH thread LH thread Maximum Minimum Maximum Minimum L2RH L2LH 1.042 0.063 0.0
9、92 0.188 0.156 0.188. 0.1139 0.1094 0.031 0.015 S2RH S2LH L3RH L3LH 1.261 0.133 0.250 0.187 0.250 0.1638 0.1568 0.047 S3RH S3LH L4RH L4LH 1.511 0.195 0.313 0.250 0.313 0.2224 0.2152 S4RH S4LH L5RH L5LH 1.761 S5RH S5LH L6RH L6LH 2.011 0.245 0.375 0.312 0.375 0.2830 0.2754 S6RH S6LH -7RH -7LH 2.261 0.
10、306 0.438 0.375 0.438 0.3454 0.3378 -8RH -8LH 2.511 0.500 0.438 0.500 -9RH -9LH 2.761 0.361 0.625 0.563 0.625 0.4052 0.3972 -10RH -10LH 3.011 0.406 0.688 0.625 0.688 0.4678 0.4597 0.063 0.031 -12RH -12LH 3.511 0.476 0.750 0.688 0.750 0.5285 0.5201 -14RH -14LH 4.011 0.538 0.812 0.750 0.812 0.5909 0.5
11、826 -16RH -16LH 4.698 0.875 0.812 0.875 -18RH -18LH 5.011 0.654 1.000 0.875 1.000 0.7137 0.7050 0.078 0.048 -20RH -20LH 5.511 0.768 1.125 1.000 1.125 0.8558 0.8266 -24RH -24LH 6.511 0.893 1.438 1.125 1.438 0.9608 0.9516 -28RH -28LH 7.166 1.002 1.625 1.438 1.625 1.0819 1.0772 0.094 0.062 -32RH -32LH
12、8.229 1.128 1.875 1.625 1.812 1.2069 1.1972 TABLE I. Dash numbers and dimensions - Continued. Dash number L 0.063 Ls reference M N P Q +0.031 -0.016 S +0.062 -0.000 T L2 3.491 3.67 0.090 +0.010 -0.000 0.078 +0.005 -0.000 1.042 +0.031 -0.000 1.319 0.969 0.138 +0.000 -0.005 S2 2.616 2.79 L3 3.738 3.86
13、 0.119 0.109 1.261 1.581 1.188 0.190 S3 2.863 2.98 L4 4.020 4.28 0.154 0.141 1.511 1.863 1.438 0.219 S4 3.145 3.40 L5 4.314 4.66 0.188 0.172 1.761 2.157 1.688 0.250 S5 3.439 3.78 L6 4.612 4.78 0.223 0.203 2.011 2.455 1.938 0.313 S6 3.737 3.90 -7 4.914 5.21 0.257 0.234 2.261 2.757 2.188 0.375 +0.000
14、-0.007 -8 5.218 5.52 0.291 0.265 2.511 3.061 2.438 0.438 -9 5.542 5.90 0.326 0.297 2.761 3.385 2.688 0.500 +0.000 -0.008 -10 5.875 6.30 0.360 0.328 3.011 3.718 2.938 0.563 -12 6.608 7.01 0.430 +0.012 -0.000 0.404 +0.008 -0.000 3.511 +0.047 -0.000 4.281 3.438 0.625 -14 7.468 7.94 0.514 0.468 4.011 4.
15、812 3.938 0.688 -16 8.718 9.28 0.584 0.531 +0.009 -0.000 4.698 5.562 4.625 0.750 +0.000 -0.009 -18 9.188 9.78 0.653 0.594 5.011 6.000 4.938 0.875 -20 10.469 11.16 0.722 0.656 +0.010 -0.000 5.511 +0.062 -0.000 6.750 5.438 1.000 +0.000 -0.010 -24 12.188 12.76 0.860 +0.015 -0.000 0.781 +0.012 -0.000 6.
16、511 7.938 6.438 1.250 +0.000 -0.012 -28 12.851 13.61 1.013 0.921 7.166 8.601 7.094 1.437 -32 14.624 15.53 1.151 1.046 8.229 9.844 8.156 1.625 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS21260N 4 TABLE I. Dash numbers and dimensions - Continued.
17、 Dash number U reference V 0.005 W 0.016 X Y 0.047 2/ Z BB Minimum Minimum L2 0.094 0.063 1.174 0.70 0.375 0.03 0.008 (0.016 FIM) S2 L3 1.411 0.80 0.500 S3 L4 0.125 0.098 1.682 1.05 0.563 S4 L5 1.958 1.29 0.625 S5 L6 2.237 1.31 0.750 S6 -7 2.518 1.55 0.875 -8 2.784 1.70 -9 3.076 1.89 1.000 -10 3.326
18、 2.06 -12 3.828 3.12 1.125 0.010 (0.020 FIM) -14 4.375 3.57 1.250 -16 0.188 0.125 5.093 4.31 -18 5.468 4.51 1.500 -20 6.093 5.04 1.750 0.015 (0.030 FIM) -24 7.188 5.80 2.000 -28 7.846 6.31 0.020 (0.040 FIM) -32 9.000 7.26 2.250 2/ Includes last full thread engagement. REQUIREMENTS: 1. Material: Mate
19、rial shall be in accordance with MIL-DTL-781 2. Finish: Finish shall be in accordance with MIL-DTL-781. 3. Threads: Threads shall be in accordance with FED-STD-H28/20. 4. Swage: Swage shall be in accordance with MIL-DTL-6117. 5. Tolerances: Unless otherwise specified, tolerances: decimals 0.010, ang
20、les 3. NOTES: 1. The part or identifying number (PIN) to be used for terminals acquired to this specification is created as shown below. An “L“ in lieu of dash indicates long; an “S“ in lieu of a dash indicates short. The two letters following the dash number or letters “L“ or “R“ indicates directio
21、n of thread (left or right hand). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS21260N 5 EXAMPLE: MS 21260 - 7RH Dash number (see table I) Use “L“ for long or “S“ for short Specification sheet number MS prefix MS21260L2RH Indicates - Terminal, 0.
22、1380 (#6)-40 right hand thread, long. MS21260-7RH Indicates - Terminal, 0.3750 (3/8)-24 right hand thread. 2. Dimensions are in inches. 3. Remove burrs and sharp edges. (See MIL-DTL-781.) 4. Interpret drawing in accordance with ASME Y14.5M. 5. In the event of a conflict between the text of this docu
23、ment and the references cited herein, the text of this document takes precedence. 6. Unless otherwise specified, issues of reference documents are those in effect at the time of solicitation. 7. Interchangeability relationship: MS21260 parts can universally replace the canceled AN669 and NAS650 part
24、s identified by the same dash number; but the canceled AN669 and NAS650 parts cannot replace the superseding MS21260 parts. MS21260 corrosion resistant steel parts can universally replace the canceled carbon and alloy steel parts identified by the same dash number. 8. Carbon and alloy steel parts ar
25、e inactive for new design. 9. Cutter radius mark, which is used as a clip slot alignment indicator, must be present on this surface. 10. During fabrication of the clip slot groove, operation of the cutter shall be maintained for the length of the terminal shank until engagement of the wrenching shou
26、lder surface occurs (see note 9). Depending upon the part tolerance conditions, the cutter radius marks may or may not appear on shank surface and shall not be cause for rejection. 11. Locking clip slot (dimension G) is optional for sizes -12 and above. 12. Marking: Complete MS part number, indented
27、. Use two faces if required. For terminal sizes -2 through -5, use basic part number only, example, MS21260. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS21260N 6 CHANGES FROM PREVIOUS ISSUE: The margins of this specification are marked with ver
28、tical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the en
29、tire content irrespective of the marginal notations and relationship to the last previous issue. Custodians: Preparing Activity: Army - CR4 Navy - AS Air Force - 99 DLA - GS DLA - GS5 (Project 1640-2011-011) Review Activities: Navy - MC Air Force - 71 NOTE: The activities listed above were intereste
30、d in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST database at https:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
