1、AMSC N/A FSC 5930 INCH-POUND MS21356J 5 October 2011 SUPERSEDING MS21356H 4 September 1991 DETAIL SPECIFICATION SHEET SWITCH, TOGGLE, POSITIVE BREAK, MINIATURE, TOGGLE SEALED, PRINTED CIRCUIT BOARD TERMINALS, SINGLE POLE, .469 MOUNTING BUSHING This specification is approved for use by all Department
2、s and Agencies of the Department of Defense. The requirements for acquiring the products described herein shall consist of this specification sheet and MIL-DTL-8834. FIGURE 1. Dimensions and configuration. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-
3、MS21356J 2 Inches mm Inches mm Inches mm .005 .008 .012 .025 .030 .032 0.13 0.20 0.30 0.64 0.76 0.81 .038 .055 .072 .160 .200 .240 0.97 1.40 1.83 4.06 5.08 6.10 .364 .432 .438 .469 .572 .687 .750 9.25 10.97 11.13 11.91 14.53 17.45 19.05 NOTES: 1. Dimensions are in inches. 2. Metric equivalents a
4、re given for general information only. 3. Unless otherwise specified, tolerances are .010 (0.25 mm) on decimals and 5 on angles. 4. Terminals need not be marked. Terminal identification is shown for reference purposes only. FIGURE 1. Dimensions and configuration - Continued. REQUIREMENTS: For hardwa
5、re detail specifications, see appendix of MIL-DTL-8834. In the event of a conflict between the text of this specification and the references cited herein, the text of this specification shall take precedence. Dielectric withstanding voltage: For center on circuits, DWV shall be 1,200 V rms at sea le
6、vel. Toggle seal test: Method II. The switch shall be electrically and mechanically operative at the conclusion of the shock test with 2,000 foot pounds, except there can be transfer of the contact mechanism at all levels when tested in accordance with MIL-STD-202 , method 207. Terminals: Gold plate
7、d. Weight: .0429 pound maximum (19.4 grams). Strength of terminals: 5 pounds normal to the mounting plane and 1 pound in other planes. Altitude: 50,000 feet. 115 V ac 60 hertz electrical endurance tests are to be performed at room temperature and pressure. Provided by IHSNot for ResaleNo reproductio
8、n or networking permitted without license from IHS-,-,-MS21356J 3 TABLE I. Detail requirements. MS dash no Circuit made between terminals as indicated with the toggle lever in these positions: 1/ Current capacity in amperes Low current level switching 5 mV Resistive load Inductive load 28 volts dc 1
9、15 volts 28 volts dc 115 volts Opposite locking tab side 4/ Center position Locking tab side 4/ 60 Hertz ac 400 Hertz ac 60 Hertz ac 400 Hertz ac -211 on 2-3 off on 1-2 5 2 3 1 2/ 1 2 25 A 3/ -221 none off -231 on 1-2 -241 off none -271 mom-on 2-3 mom-on 1-2 -281 none -311 on 2-3 -321 5/ none on 2-3
10、 1/ Direction of movement of internal mechanism is opposite to the direction of the toggle movement. 2/ With time constant of .020 .002 second. 3/ Contact resistance not to exceed 50 during life, low current level switching. 4/ Non-functional terminals shall not be supplied. 5/ Delayed action of the
11、 switch toggle lever may cause circuit to close or open before snap action mechanism trips. Referenced documents: MIL-DTL-8834 MIL-STD-202. Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the ch
12、anges. Custodians: Preparing activity: Navy - AS DLA CC Air Force - 85 DLA - CC (Project 5930-2011-077) Review activities: Navy - EC Air Force - 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil/ . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
