1、 MS24588C INCH-POUND14 May 2007 SUPERSEDING MS24588B 22 September 2000 DETAIL SPECIFICATION SHEET NIPPLE, ADAPTER, HOSE TO TUBE, REUSABLE, HYDRAULIC, FUEL AND OIL LINES, 3/16 THROUGH 3/4 INCH TUBING SIZES This specification is approved for use by all Departments and Agencies of the Department of Def
2、ense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-5070. Inches mm .005 .010 .030 .25000.13 0.25 0.76 0.635FIGURE 1. Nipple dimension and configuration. AMSC N/A FSC 4730 Provided by IHSNot for ResaleNo reproduction or networking p
3、ermitted without license from IHS-,-,-MS24588C 2 Dash number A inches (mm) B inches (mm) C inches (mm) D inches (mm) E inches (mm) F inches (mm) G inches (mm) H inches (mm) J inches (mm) -3 1.275 (32.39) 1.255 (31.88) .326 (8.28) .321 (8.15) .185 (4.70) .180 (4.57) .234 (5.94) .228 (5.79) .235 (5.97
4、) .227 (5.77) .203 (5.16) .198 (5.03) .188 (4.78) .183 (4.65) .093 (2.36) .495 (12.57) -4 1.305 (33.15) 1.285 (32.64) .379 (9.63) .374 (9.50) .243 (6.17) .237 (6.02) .281 (7.14) .275 (6.99) .291 (7.39) .283 (7.19) .250 (6.35) .245 (6.22) .183 (4.65) .178 (4.52) .093 (2.36) .490 (12.45) -5 1.450 (36.
5、83) 1.430 (36.32) .442 (11.23) .437 (11.10) .308 (7.82) .302 (7.67) .365 (9.27) .357 (9.07) .368 (9.35) .360 (9.14) .329 (8.36) .324 (8.23) .199 (5.05) .194 (4.93) .107 (2.72) .565 (14.35) -6 1.665 (42.29) 1.645 (41.78) .504 (12.80) .499 (12.67) .368 (9.35) .362 (9.19) .421 (10.69) .414 (10.52) .429
6、 (10.90) .421 (10.69) .388 (9.86) .383 (9.73) .223 (5.66) .218 (5.54) .107 (2.72) .605 (15.37) -8 1.943 (49.35) 1.923 (48.84) .684 (17.37) .679 (17.25) .463 (11.76) .457 (11.61) .5625 (14.29) .5540 (14.07) .563 (14.30) .555 (14.10) .521 (13.23) .516 (13.11) .296 (7.52) .291 (7.39) .126 (3.20) .683 (
7、17.35) -10 2.100 (53.34) 2.080 (52.83) .800 (20.32) .795 (20.19) .579 (14.71) .573 (14.55) .6875 (17.46) .6790 (17.25) .692 (17.58) .684 (17.37) .646 (16.41) .641 (16.28) .312 (7.92) .307 (7.80) .126 (3.20) .730 (18.54) -12 2.424 (61.57) 2.404 (61.06) .975 (24.77) .970 (24.64) .690 (17.53) .682 (17.
8、32) .8125 (20.64) .8030 (20.40) .814 (20.68) .806 (20.47) .740 (18.80) .735 (18.67) .300 (7.62) .295 (7.49) .150 (3.81) .714 (18.14) FIGURE 1. Nipple dimension and configuration - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS24588C 3
9、Dash number K inches (mm) L inches (mm) M inches (mm) N .25 P (see note 5) PD S inches (mm) -3 .270 (6.86) .255 (6.48) .235 (5.97) .128 (3.25) .123 (3.12) 5 .234-32 UNS-2A .2131 .2100 .010 (.25) .005 (.13) -4 .200 (5.08) .305 (7.75) .285 (7.24) .175 (4.45) .170 (4.32) 4.5 .281-32 UNS-2A .2597 .2565
10、015 (.38) .009 (.23) -5 .280 (7.11) .365 (9.27) .345 (8.76) .237 (6.02) .232 (5.89) 4 .365-28 UNS-2A .3398 .3365 -6 .260 (6.60) .445 (11.30) .425 (10.80) .300 (7.62) .295 (7.49) 4 .421-28 UNS-2A .3968 .3932 -8 .480 (12.19) .580 (14.73) .560 (14.22) .394 (10.01) .390 (9.91) 4.5 .562-24 UNEF-2A - -10
11、 .515 (13.08) .690 (17.53) .670 (17.02) .488 (12.40) .484 (12.29) 5 .687-24 UNEF-2A - -12 .590 (14.99) .860 (21.84) .840 (21.34) .612 (15.54) .608 (15.44) 4 .812-20 UNEF-2A - .020 (.51) .010 (.25) NOTES 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless othe
12、rwise specified, tolerances are as follows: Angles .5; decimals .005 inch (0.13 mm). 4. Unless otherwise specified, maximum surface roughness shall be 125 in Rain accordance with ASME B46.1. 5. Threads shall be in accordance with MIL-S-7742. 6. Break all sharp edges and remove all hanging burrs and
13、slivers. 7. Part or Identifying Number (PIN). FIGURE 1. Nipple dimension and configuration - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS24588C 4 REQUIREMENTS: Dimensions and configurations: The design, construction, and physical dim
14、ensions shall be in accordance with MIL-DTL-5070 and figure 1 in case of conflict between this drawing and MIL-DTL-5070, this drawing shall govern. Intended use: This part is a component of MS24587. Materials: Materials shall be in accordance with MIL-DTL-5070. Finish: Finish shall be in accordance
15、with MIL-DTL-5070. Color identification: Color identification shall be accordance with MIL-DTL-5070. PIN example: MS 24588 -3 CCMaterial/finish code, see table I Dash number on figure 1 Specification number MS prefix TABLE I. Code for material and finish. Code Dash size Material/finish CC -3 thru -6
16、 Carbon Steel cadmium plating CZ -3 thru -6 Carbon steel zinc plating SS -3 through -6 Corrosion resistant steel - N/A AA -8 through -12 Aluminum anodic coating TA -3 through -12 Titanium - Anodized or fluoride phosphated. To the users of this document, it is recommended that the use of carbon steel
17、 material with cadmium plating be used only when the other materials and finishes specified in this document cannot meet performance requirements. Marking: The manufacturers Commercial and Government Entity (CAGE) Code or trademark shall be permanently marked on the nipple, see figure 1, or on a rem
18、ovable tag securely attached to the nipple. Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue, due to the extent of the changes. Referenced documents. In addition to MIL-DTL-5070, this document references the followin
19、g: MIL-S-7742 MS24587 ASME B46.1 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS24588C 5 CONCLUDING MATERIAL Custodians: Preparing activity: Army - AT DLA - CC Navy - AS Air Force - 99 (Project 4730-2005-038) DLA - CC Review activities: Army - AV
20、Navy - MC, SA Air Force - 11, 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
