1、 MS24589C INCH-POUND14 May 2007 SUPERSEDING MS24589B 22 September 2000 DETAIL SPECIFICATION SHEET NIPPLE, ADAPTER, HOSE TO TUBE, REUSABLE, HYDRAULIC, FUEL AND OIL LINES, 1 THROUGH 2 INCHES TUBING SIZES This specification is approved for use by all Departments and Agencies of the Department of Defens
2、e. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-5070. Inches mm .005 .010 .030 .047 .078 .137 0.13 0.25 0.76 1.19 1.98 2.54 FIGURE 1. Nipple dimensions and configuration. AMSC N/A Provided by IHSNot for ResaleNo reproduction or net
3、working permitted without license from IHS-,-,-FSC4730 MS24589C 2 Dash number A inches (mm) B inches (mm) C inches (mm) D inches (mm) E inches (mm) F inches (mm) G inches (mm) H inches (mm) J inches (mm) -16 2.146 (54.51) 2.126 (54.00) 1.224 (31.09) 1.218 (30.94) 1.061 (26.95) 1.052 (26.72) .900 (22
4、86) .890 (22.61) .990 (25.15) .980 (24.89) .363 (9.22) .358 (9.09) .692 (17.58) 1.118 (28.40) 1.088 (27.64) .200 (5.08) -20 2.372 (60.25) 2.352 (59.74) 1.536 (39.01) 1.530 (38.86) 1.311 (33.30) 1.302 (33.07) 1.125 (28.58) 1.115 (28.32) 1.235 (31.37) 1.225 (31.12) .380 (9.65) .370 (9.40) .746 (18.95
5、) 1.425 (36.20) 1.395 (35.43) .200 (5.08) -24 2.503 (63.58) 2.483 (63.07) 1.786 (45.36) 1.781 (45.24) 1.561 (39.65) 1.552 (39.42) 1.360 (34.54) 1.350 (34.29) 1.500 (38.10) 1.480 (37.59) .436 (11.07) .426 (10.82) .814 (20.68) 1.640 (41.66) 1.610 (40.89) .150 (3.81) -32 3.094 (78.59) 3.074 (78.08) 2.4
6、10 (61.21) 2.405 (61.09) 1.998 (50.75) 1.990 (50.55) 1.830 (46.48) 1.820 (46.23) 1.935 (49.15) 1.915 (48.64) .536 (13.61) .526 (13.36) .940 (23.88) 2.255 (57.28) 2.225 (56.52) .200 (5.08) Dash number K .25 L inches (mm) M PD -16 5 .815 (20.70) 1.062-18 UNEF-2A- -20 5 1.047 (26.59) 1.312-18 UNEF-2A-
7、24 5 1.281 (32.54) 1.562-18 UNEF-2A- -32 4 1.750 (44.45) 2.000-18 UNS-2A (see note 7) 1.9624 1.9573 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerances are as follows: angles .5; decimals .005 (0.13 mm). 4. Unless other
8、wise specified, maximum surface roughness shall be 125 in Rain accordance with ASME B46.1 5. Threads shall be in accordance with MIL-S-7742. 6. Break all sharp edges and remove all hanging burrs and slivers. 7. Pitch diameter. 8. Part or Identifying Number (PIN). FIGURE 1. Nipple dimensions and conf
9、iguration - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS24589C 3 REQUIREMENTS: Dimensions and configurations: The design, construction, and physical dimensions shall be in accordance with MIL-DTL-5070 and figure 1 in case of conflict
10、 between this drawing and MIL-DTL-5070, this drawing shall govern. Intended use. This part is a component of MS24587. Material: Aluminum shall be in accordance with MIL-DTL-5070. Finish. Finish shall be in accordance with MIL-DTL-5070. Color identification: Color identification shall be accordance w
11、ith MIL-DTL-5070. Part or Identifying Number (PIN) example: MS 24589 -16 AA Material/finish code, see table I Dash number on figure 1 Specification number MS prefix PIN example: TABLE I. Code for material and finish. Code Dash size Material/finish AA -16 through -32 Aluminum anodic coating Changes f
12、rom previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue, due to the extent of the changes. Referenced documents: In addition to MIL-DTL-5070, this document references the following: ASME B46.1 MIL-S-7742 MS24587 Provided by IHSNot f
13、or ResaleNo reproduction or networking permitted without license from IHS-,-,-MS24589C 4 CONCLUDING MATERIAL Custodians: Preparing activity: Army - AT DLA - CC Navy - AS Air Force - 99 (Project 4730-2005-039) DLA - CC Review activities: Army - AV Navy - MC, SA Air Force - 11, 71 NOTE: The activities
14、 listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
