1、 AMSC N/A 1 of 5 FSC 5945 INCH-POUND MS25465F 27 November 2003 SUPERSEDING MS25465E 20 Jan 1989 DETAIL SPECIFICATION SHEET RELAYS, ELECTROMAGNETIC, 5 AMPERES, 2 PDT, TYPE I, MAGNETIC LATCH, SOLDER TERMINALS, STUD MOUNTED, HERMETICALLY SEALED INACTIVE FOR NEW DESIGN AFTER 5 JUN 1987. NO SUPERSEDING S
2、PECIFICATION. (FOR NEW DESIGN USE MIL-PRF-6106/38) This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the relay described herein shall consist of this specification and the latest issue of MIL-PRF-6106. FIGURE 1. Design
3、, dimensions, and circuit diagram.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS25465F 2 Inches mm .000 0.00 .001 0.03 .005 0.13 .040 1.02 .062 1.57 .152 3.86 .172 4.37 .250 6.35 .375 9.53 .500 12.70 .687 17.45 .843 21.41 1.187 30.15 1.531 38.89
4、1.750 44.45 NOTES: 1/ Dimensions are in inches. 2/ Metric equivalents are given for general information only. 3/ Unless otherwise specified, tolerance is .010 (0.25 mm). 4/ Terminal numbers need not appear on relay headers provided there is affixed to the relay a suitable legible circuit diagram tha
5、t permanently and positively identifies each terminal location specified hereon. 5/ The use of diodes on ac relays is optional. Actual application must be shown on label. 6/ Relay is magnetically latched in both positions. Caution note to observe polarity must appear on relays with dc coils. 7/ Shoc
6、k, vibration, and acceleration requirements application with coils de-energized. 8/ In the event of conflict between the text of this standard and the references cited herein, the text of this standard shall take precedence. 9/ Referenced Government documents of the issue listed in that issue of the
7、 Department of Defense Index of Specifications and Standards (DoDISS) specified in the solicitation form a part of this standard to the extent specified herein. 10/ Pins to be perpendicular to header surface within 1 degree. 11/ Relay is magnetically latched in both positions. Caution note to observ
8、e polarity must appear on relays with dc coils. 12/ Shock, vibration, and acceleration requirements application with coils de-energized. FIGURE 1. Design, dimensions, and circuit diagram - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS
9、25465F 3 TABLE I. Dash numbers and characteristics. Dash number MS25465- Type Coil Terminal type Mounting means Max weight in pounds D1 I dc Solder hook Stud 0.18 A1 I ac Solder hook Stud 0.19 AD1 I ac-dc Solder hook Stud 0.19 TABLE II. Operating characteristics. Coil data Time - milliseconds max Ra
10、ted Max Max pick-up voltage Contact Bounce Main Aux PIN MS25465- Coil Volts 1/ Freq Hz Res Volts Amp Nor- mal 2/ High temptest Cont cur-rent test Drop out vol-tage Op-erate 3/ Rel-ease 4/ NO NC NO NC D1 X1, X2 Y1, Y2 28 dc N/A 29 0.12 18 18 19.8 N/A 25 N/A 2 2 N/A N/A A1 X1, X2 Y1, Y2 115 400 5/ N/A
11、 122 0.06 90 90 95 N/A 25 N/A 2 2 N/A N/A AD1 X1, X2 115 400 5/ N/A 122 0.06 90 90 95 N/A 25 N/A 2 2 N/A N/A Y1, Y2 28 dc N/A 29 0.12 18 18 19.8 N/A 25 N/A 2 2 N/A N/A 1/ CAUTION: Use of any coil voltage less than rated coil voltage will compromise the operation of the relay. 2/ Over the temperature
12、 range. 3/ With nominal coil voltage. 4/ From nominal coil voltage. 5/ MS25465-A1 and -AD1 may be used on 60 Hz if maximum ambient temperature is limited to +85C (maximum coil current shall be 0.066 ampere). TABLE II. Rated contact load (amperes per pole) (case grounded). 28 V dc 115 V ac, 1 phase 1
13、15/200 V ac, 3 phase 1/ Main Aux Main Aux Main Aux Type of load Life operating cycles x 103NO NC NO NC 400 Hz 60 Hz 400 Hz 60 Hz 400 Hz 60 Hz 400 Hz 60 Hz See appropriate notes Resistive 100 5 5 5 4 Inductive 100 Inductive 20 3 3 3 2 Motor 100 1.5 1.5 1.5 1 Lamp 100 0.8 0.8 0.8 0.6 Transfer load 2/
14、Mechanical life reduced current 400 1.25 1.25 1.25 1 Mixed loads Applicable per specification 1/ Absence of value indicates relay is not rated for 3-phase application. 2/ Transfer load indicates relay is suitable for transfer between unsynchronized ac power supplies at rating indicated Provided by I
15、HSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS25465F 4 REQUIREMENTS: Environmental characteristics: Temperature range -70C to +125C Max altitude rating 80,000 ft Shock G-level 50 gs Duration 11 ms Max duration contact opening 10 s Vibration sinusoidal G-level
16、 10 gs Frequency range 5-1,500 Hz Acceleration 15 gs Electrical characteristics: Insulation resistance, initial 100 megohms. After life or environmental tests 50 megohms. Dielectric strength (sea level). Initial After life tests Coil to case 1,000 V rms 1,000 V rms Aux contacts All other points 1,00
17、0 V rms 1,000 V rms Dielectric strength (altitude). (When mounted in mating socket) 80,000 ft Coil to case 250 V rms Aux contacts All other points 250 V rms Max contact drop initial 0.150 volt. After life test 0.175 volt. Overload current 20 amperes Rupture current 25 amperes Duty rating Continuous.
18、 RFI specification MIL-STD-461. (Applicable to coil circuits of ac operated relays.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS25465F 5 Conformance inspection. Performance of groups B and C tests are not applicable. Group A acceptance reports
19、 shall be submitted to the preparing activity on a yearly basis in order to retain qualification for this military specification sheet. Qualification by similarity: See MIL-PRF-6106. NOTES Referenced documents. In addition to MIL-PRF-6106, this specification sheet references the following documents.
20、 (Government documents are available on line at http:/assist.daps.dla.mil/quicksearch or www.dodssp.daps.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094). STANDARDS Department of Defense MIL-STD-461 - Requirements for the Control of E
21、lectromagnetic Interference Characteristics of Subsystems and Equipment Society of Automotive Engineers documents are available from the Society of Automotive Engineers 400 Commonwealth Drive Warrendale, Pennsylvania, United States, 15096-0001. http:/www.sae.org Society of Automotive Engineers (SAE)
22、 SAE-AMS3332 - Silicone Rubber Extreme Low-Temperature Resistant, 15-30 Custodians: Preparing activity:Navy - AS DLA - CC Air Force - 11 DLA - CC (Project 5945-1214-12) Review activities: Navy EC NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using ASSIST Online database at www.dodssp.daps.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
