1、 INCH-POUND MS27236B 14 May 2007 SUPERSEDING MS27236A 22 September 2000 DETAIL SPECIFICATION SHEET SHOULDER - DESIGNED FOR 45 AND 90 SWIVEL NUT, HOSE TO TUBE ADAPTERS, REUSABLE, HYDRAULIC, FUEL AND OIL LINES This specification is approved for use by all Departments and Agencies of the Department of
2、Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-5070. FIGURE 1. Shoulder dimensions and configuration.AMSC N/A FSC 4730 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27236
3、B 2 FIGURE 1. Shoulder dimensions and configuration - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27236B 3 Dash number A .007 (0.18) inches (mm) B Dia inches (mm)C D E max F inches (mm) G (ref) H inches (mm) J inches (mm) -4 .344 (8.
4、74) .305 (7.75) .285 (7.24) .190 (4.83) .185 (4.70) .076 (1.93) -5 .406 (10.31) .365 (9.27) .345 (8.76) .253 (6.43) .248 (6.30) -6 .422 (10.72) .445 (11.30).425 (10.80)0 0 30 .269 (6.83) .264 (6.71) .118 (3.00) .089 (2.26) .086 (2.18) -8 .437 (11.10) .580 (14.73).560 (14.22)2 .285 (7.24) .280 (7.11)
5、 -10 .500 (12.70) .690 (17.53).670 (17.02).347 (8.81) .342 (8.69) .156 (3.96) .100 (2.54) -12 .860 (21.84).840 (21.34).046 (1.17) .031 (.79)-16 .531 (13.49) 1.118 (28.40)1.088 (27.64).284 (7.21) .279 (7.09) -20 .594 (15.09) 1.425 (36.20)1.395 (35.43).347 (8.81) .342 (8.69) -24 .656 (16.66) 1.640 (41
6、.66)1.610 (40.89).409 (10.39) .404 (10.26) .077 (1.96) .062 (1.57) -32 .781 (19.84) 2.255 (57.28)2.225 (56.52)34 1.5 10 .534 (13.56) .529 (13.44) .250 (6.35) .046 (1.17) .031 (.79).130 (3.30) FIGURE 1. Shoulder dimensions and configuration - Continued.Provided by IHSNot for ResaleNo reproduction or
7、networking permitted without license from IHS-,-,-MS27236B 4 Dash number K .002 (0.05) inches (mm) L Dia inches (mm) M Dia inches (mm) N Dia inches (mm) P Dia inches (mm) Q Dia inches (mm) S inches (mm) -4 .129 (3.28) .178 (4.52) .254 (6.45) .251 (6.38) .298 (7.57) .293 (7.44) .384 (9.75) .379 (9.63
8、) -5 .173 (4.39) .209 (5.31) .316 (8.03) .313 (7.95) .346 (8.79) .341 (8.66) .447 (11.35) .442 (11.23) -6 .196 (4.98) .272 (6.91) .379 (9.63) .376 (9.55) .403 (10.24) .398 (10.11) .504 (12.80) .499 (12.67) .015 X 45 (0.38 X 45) max. break -8 .225 (5.72) .365 (9.27) .420 (10.67) .504 (12.80) .501 (12
9、.73) .564 (14.33) .559 (14.20) .684 (17.37) .679 (17.25) -10 .261 (6.63) .490 (12.45) .545 (13.84) .629 (15.98) .626 (15.90) .679 (17.25) .674 (17.12) .800 (20.32) .795 (20.19) -12 .214 (5.44) .615 (15.62) .670 (17.02) .754 (19.15) .751 (19.08) .821 (20.85) .816 (20.73) .972 (24.69) .967 (24.56) .01
10、5 (.38) .010 (.25) radius -16 .243 (6.17) .865 (21.97) .920 (23.37) 1.004 (25.50) 1.001 (25.43) 1.088 (27.64) 1.080 (27.43) 1.219 (30.96) 1.213 (30.81) -20 .322 (8.18) 1.115 (28.32) 1.170 (29.72) 1.254 (31.85) 1.251 (31.78) 1.385 (35.18) 1.377 (34.98) 1.531 (38.89) 1.525 (38.74) -24 .338 (8.59) 1.32
11、9 (33.76) 1.295 (32.89) 1.504 (38.20) 1.501 (38.13) 1.638 (41.61) 1.630 (41.40) 1.781 (45.24) 1.775 (45.09) .030 (.76) radius -32 .414 (10.52) 1.829 (46.46) 1.795 (45.59) 2.004 (50.90) 2.001 (50.83) 2.263 (57.48) 2.255 (57.28) 2.406 (61.11) 2.400 (60.96) .015 (.38) .010 (.25) radius FIGURE 1. Should
12、er dimensions and configuration - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27236B 5 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are for information only. 3. Unless otherwise specified, tolerances: angles 0.5 Decimals
13、 + .000/ -.005 (+.00/-.13mm). 4. Break all corners, radius .010/.005 (.25/.01 mm). 5. All diameters shall be concentric within .010 inch (0.25 mm) total indicator reading. 6. Unless otherwise specified, maximum surface roughness shall be 125 in Rain accordance with ASME B46.1. 7. Break all sharp edg
14、es and remove all burrs and slivers. FIGURE 1. Shoulder dimensions and configuration - Continued. REQUIREMENTS: Dimensions and configurations: The design, construction, and physical dimensions shall be in accordance with MIL-DTL-5070 and figure 1 in case of conflict between this drawing and MIL-DTL-
15、5070, this drawing shall govern. Intended use. This part is a component of MS27223, MS27225, MIL-DTL-5070/1 and MIL-DTL-5070/2. This item shall not be procured for stocking purposes. Materials: Materials shall be in accordance with MIL-DTL-5070. Finish: Finish shall be in accordance with MIL-DTL-507
16、0. Platings are applied after heat treats. Color identification: Color identification shall be in accordance with MIL-DTL-5070. Part or Identifying Number (PIN) example: MS 27236 -4 CZMaterial/finish code, see table I Dash number on figure 1 Specification number MS prefix TABLE I. Code for material
17、and finish. Code Dash size Material/finish CC -4 through -6 Carbon Steel - cadmium plating CZ -4 through -6 Carbon steel - zinc plating SS -4 through -6 Corrosion resistant steel - N/A AA -8 through -32 Aluminum - anodic coating TA -4 through -32 Titanium - anodized or fluoride phosphated. Changes f
18、rom previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue, due to the extent of the changes. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27236B 6 Referenced documents. In additio
19、n to MIL-DTL-5070, this document references the following: MIL-DTL-5070/1 MIL-DTL-5070/2 MS27223 MS27225 ASME B46.1 CONCLUDING MATERIAL Custodians: Preparing activity: Army - AT DLA - CC Navy - AS Air Force - 99 (Project 4730-2005-054) DLA - CC Review activities: Army - AV Navy - MC, SA Air Force -
20、11, 70, 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
