1、 MS27239E INCH-POUND14 May 2007 SUPERSEDING MS27239D 22 September 2000 DETAIL SPECIFICATION SHEET NIPPLE, STRAIGHT, ADAPTER, HOSE TO TUBE, REUSABLE, HYDRAULIC, FUEL AND OIL LINES, 1/4 THROUGH 4 INCH TUBE SIZES This specification is approved for use by all Departments and Agencies of the Department o
2、f Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-5070. Inch mm .010 .020 .030 0.25 0.51 0.76 FIGURE 1. Nipple dimensions and configuration. AMSC N/A FSC 4730 Provided by IHSNot for ResaleNo reproduction or networking permitt
3、ed without license from IHS-,-,-MS27239E 2 FIGURE 1. Nipple dimensions and configuration - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27239E 3 Dash number A (ref) inches (mm) B .010 (0.25) inches (mm) C(see note 5) .010 (0.25) inche
4、s (mm)D inches (mm) E inches (mm) F inches (mm) G Dia inches (mm) H maxJ inches (mm) K Dia .02 (0.51) inches (mm) L Dia inches (mm) M Dia inches (mm) N inches (mm) -4 1.310 (33.27) .250 (6.35) 1.060 (26.92) .097 (2.46) .092 (2.34) .093 (2.36) .250 (6.35) .245 (6.22) .450 (11.43).430 (10.92).34 (8.64
5、) .254 (6.45) .251 (6.38) .175 (4.45) -5 1.491 (37.87) 1.179 (29.95) .329 (8.36) .324 (8.23) .510 (12.95).490 (12.45).41 (10.41) .316 (8.03) .313 (7.95) .235 (5.97) -6 1.666 (42.32) .312 (7.92) 1.354 (34.39) .159 (4.04) .154 (3.91) .135 (3.43) .070 (1.78) .107 (2.72) .388 (9.86) .383 (9.73) 30 .580
6、14.73).560 (14.22).47 (11.94) .379 (9.63) .376 (9.55) .272 (6.91) .125 (3.18) -8 2.000 (50.80) 1.625 (41.28) .520 (13.21).510 (12.95).719 (18.26).688 (17.48).59 (14.99) .504 (12.80) .501 (12.73) .420 (10.67).150 (3.81) -10 2.175 (55.25) 1.800 (45.72) .222 (5.64) .217 (5.51) .126 (3.20) .645 (16.38)
7、635 (16.13).859 (21.82).828 (21.03).72 (18.29) .629 (15.98) .626 (15.90) .545 (13.84).097 (2.46) -12 2.469 (62.71) 2.094 (53.19) .046 (1.17) .031 (.79) .150 (3.81) .765 (19.43).755 (19.18).984 (24.99).953 (24.21).84 (21.34) .754 (19.15) .751 (19.08) .670 (17.02).150 (3.81) -16 1.973 (50.11) .375 (9
8、53) 1.598 (40.59) .128 (3.25) .123 (3.12) .077 (1.96) .062 (1.57) .990 (25.15).980 (24.89)1.266 (32.16)1.234 (31.34)1.09 (27.69) 1.004 (25.50) 1.001 (25.43) .920 (23.37)-20 2.271 (57.68) .500 (12.70) 1.771 (44.98) .253 (6.43) .248 (6.30) 1.239 (31.47)1.219 (30.96)1.515 (38.48)1.485 (37.72)1.34 (34.
9、04) 1.254 (31.85) 1.251 (31.78) 1.170 (29.72).200 (5.08) -24 2.373 (60.27) .562 (14.27) 1.811 (46.00) .315 (8.00) .310 (7.87) .137 (3.48) 1.485 (37.72)1.465 (37.21)1.765 (44.83)1.735 (44.07)1.59 1.504 (38.20) 1.501 (38.13) 1.295 (32.89).150 (3.81) -32 2.891 (73.43) .625 (15.88) 2.266 (57.56) .378 (9
10、60) .373 (9.47) .132 (3.35) 1.926 (48.92)1.906 (48.41)2.317 (58.85)2.297 (58.34)2.09 2.004 (50.90) 2.001 (50.83) 1.795 (45.59).200 (5.08) -40 3.219 (81.76) .503 (12.78).498 (12.65)2.389 (60.68)2.369 (60.17)2.827 (71.81)2.797 (71.04)2.59 2.379 (60.43) 2.376 (60.35) 2.295 (58.29)-48 3.344 (84.94) .75
11、0 (19.05) .875 (22.23) 2.469 (62.71) .628 (15.95).623 (15.82).046 (1.17) .031 (.79) .250 (6.35) 3.014 (76.56)2.994 (76.05)10 3.515 (89.28)3.485 (88.52)3.22 3.004 (76.30) 3.001 (76.23) 2.920 (74.17)0 FIGURE 1. Nipple dimensions and configuration - Continued. Provided by IHSNot for ResaleNo reproducti
12、on or networking permitted without license from IHS-,-,-MS27239E 4 Dash number P .25 Q (see note 6) Dia inches (mm) S Dia inches (mm) T PD U inches (mm) V 2 W X Dia inches (mm) -4 .128 (3.25) .123 (3.12) .281 (7.14) .275 (6.99) .281-32 UNS-2 (see note 8) .2597.2565.378 (9.60) .371 (9.42) .172 (4.37)
13、 .167 (4.24) -5 8 .175 (4.45) .170 (4.32) .365 (9.27) .357 (9.07) .365-28 UNS-2 (see note 8) .3398.3365.440 (11.18) .433 (11.00) .225 (5.72) .220 (5.59) -6 7 .237 (6.02) .232 (5.89) .421 (10.69) .414 (10.52) .421-28 UNS-2 (see note 8) .3968.3932.503 (12.78) .496 (12.60) 45 .015 max X45 break(0.38 ma
14、x X 45 break).292 (7.42) .287 (7.29) -8 6 .360 (9.14) .355 (9.02) .562 (14.27) .555 (14.10) .563-24 UNEF - 2A (see note 7) - .628 (15.95) .621 (15.77) .415 (10.54).410 (10.41)-10 5 .460 (11.68) .450 (11.43) .688 (17.48) .680 (17.27) .688-24 UNEF - 2A (see note 7) - .753 (19.13) .746 (18.95) .520 (13
15、21).510 (12.95)-12 4.5 .582 (14.78) .576 (14.63) .812 (20.62) .804 (20.42) .813-20 UNEF - 2A (see note 7) - .878 (22.30) .871 (22.12) .650 (16.51).640 (16.26)-16 .820 (20.83) .810 (20.57) 1.062 (26.97) 1.054 (26.77) .063-18 UNEF - 2A (see note 7) - 1.128 (28.65) 1.121 (28.47) 34 .900 (22.86).890 (2
16、2.61)-20 1.052 (26.72) 1.042 (26.47) 1.312 (33.32) 1.304 (33.12) 1.313-18 UNEF - 2A (see note 7) - 1.378 (35.00) 1.371 (34.82) 1.125 (28.58)1.115 (28.32)-24 5 1.286 (32.66) 1.276 (32.41) 1.562 (39.67) 1.554 (39.47) 1.688-18 UNEF - 2A (see note 7) - 1.766 (44.86) 1.734 (44.04) 45 1.360 (34.54)1.350 (
17、34.29)-32 1.755 (44.58) 1.745 (44.32) 2.000 (50.80) 1.991 (50.57) 2.000 - 18 UNS - 2A (see note 8)1.96001.96392.270 (57.66) 2.230 (56.64) 1.830 (46.48)1.820 (46.23)-40 2.219 (56.36) 2.199 (55.85) 2.500 (63.50) 2.489 (63.22) 2.500 - 12 UN - 2A (see note 7) - 2.645 (67.18) 2.605 (66.17) - -48 4 2.823
18、71.70) 2.803 (71.20) 3.125 (79.38) 3.114 (79.10) 3.125 - 12 UN - 2A (see note 7) - 3.270 (83.06) 3.230 (82.04) 34 .015 (0.38).010 (0.25)radius - FIGURE 1. Nipple dimensions and configuration - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,
19、MS27239E 5 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are for information only. 3. Unless otherwise specified, tolerances are as follows: Angles .5; decimals .005 inch (0.13 mm). 4. Unless otherwise specified, maximum surface roughness shall be 125 in Ra in accordance with ASME B46
20、1. 5. Unless otherwise specified, all outside diameters within this length shall be concentric within .005 inch (0.13 mm) total indicator reading. 6. Hole shall be concentric with external taper within .005 inch (0.13 mm) total indicator reading for a depth of .12 inch (3.0 mm) for a depth of .12 i
21、nch (3.05 mm). 7. Threads shall be in accordance with MIL-S-7742. 8. Threads shall be in accordance with ASME B1.1 (UNS). 9. Break all sharp edges and remove all burrs and slivers. FIGURE 1. Nipple dimensions and configuration - Continued. REQUIREMENTS: Dimensions and configurations: The design, con
22、struction, and physical dimensions shall be in accordance with MIL-DTL-5070 and figure 1 in case of conflict between this drawing and MIL-DTL-5070, this drawing shall govern. Intended use. This item shall not be procured for stocking purposes. This part is a component of MS27223, MS27225, MS27227, a
23、nd MS27229. Materials: Materials shall be in accordance with MIL-DTL-5070. Finish: Finish shall be in accordance with MIL-DTL-5070. Color identification: Color identification shall be in accordance with MIL-DTL-5070. Part or Identifying Number (PIN) example: MS 27239 -4 CZ Material/finish code see t
24、able I Dash number on figure 1 Specification number M prefix Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27239E 6 TABLE I. Code for material and finish. Code Dash size Material/finish CC -3 thru -6 Carbon Steel cadmium plating CZ -3 thru -6 Car
25、bon steel zinc plating SS -3 through -6 Corrosion resistant steel - N/A AA -8 through -48 Aluminum anodic coating TA -3 through -48 Titanium - Anodized or fluoride phosphated. To the users of this document, it is recommended that the use of carbon steel material with cadmium plating be used only whe
26、n the other materials and finishes specified in this document cannot meet performance requirements. Identification of product. The PIN and the manufacturers Commercial and Government Entity (CAGE) Code or trademark shall be permanently marked on the nipple or on a removable tag securely attached to
27、the part. Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue, due to the extent of the changes. Referenced documents. In addition to MIL-DTL-5070, this document references the following: MIL-S-7742 MS27223 MS27225 MS27
28、227 MS27229 ASME B1.1 ASME B46.1 CONCLUDING MATERIAL Custodians: Preparing activity: Army - AT DLA - CC Navy - AS Air Force - 99 (Project 4730-2005-057) DLA - CC Review activities: Army - AV Navy - MC, SA Air Force - 11, 70, 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
