1、INCH-POUND MS27266B 7 January 2009 SUPERSEDING MS27266A 17 June 2003 DETAIL SPECIFICATION SHEET INSERT, ELECTRICAL CONNECTOR - RAMP POWER, 416/240 VOLTS, MALE This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the produ
2、ct described herein shall consist of this specification sheet and MIL-DTL-38159. Inches mm Inches mm Inches mm .005 .010 .015 .031 .032 .062 .093 .125 .250 .350 .375 .406 .127 .254 .381 .787 .813 1.575 2.362 3.175 6.350 8.890 9.525 10.319 .438 .562 .586 .588 .654 .664 .829 1.000 1.175 1.302 1.658 2.
3、250 11.125 14.287 14.884 14.935 16.612 16.866 21.057 25.400 29.845 33.071 42.113 57.150 2.575 2.640 2.937 3.125 3.156 3.250 3.375 3.531 7.032 8.218 65.405 67.056 74.600 79.375 80.162 82.550 85.725 89.687 178.61 208.74 NOTES: 1. Dimensions are in inches. Metric equivalents are given for information o
4、nly. 2. The procurement specification for this part is MIL-DTL-38159. 3. Material: See procurement specification. 4. Remove all sharp edges. 5. Unless otherwise specified, tolerances on decimals are .010 inch. 6. For design feature purposes, this standard takes precedence over procurement documents
5、referenced herein. 7. Referenced documents shall be of the issue in effect on date of Invitation for Bid. 8. Part or Identifying Number (PIN): MS27266-1. 9. Electrical contact. See figure 2. 10. Electrical contact. See figure 3. FIGURE 1. Configurations and dimensions for MS27266-1. AMSC N/A FSC 593
6、5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27266B 2 FIGURE 1. Configurations and dimensions for MS27266-1 - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27266B 3 Inches mm Inc
7、hes mm .003 .004 .005 .063 .094 .188 .375 .406 .438 .500 .563 .076 .102 .127 1.588 2.381 4.763 9.525 10.319 11.113 12.700 14.288 .594 .656 .687 .718 .750 .813 1.000 2.750 6.781 15.081 16.669 17.450 18.237 19.050 20.638 25.40 69.85 172.24 NOTES: 1. For use with PIN MS27266-1. 2. Procurement specifica
8、tion MIL-DTL-38159. 3. Material: Copper alloy See procurement specification. 4. Finish: See procurement specification. 5. Unless otherwise specified, machined surfaces 125 or better in accordance with ASME B46.1. 6. Remove all burrs and break all edges. 7. All dimensions shown are for finished part
9、after plating. 8. Dimensions in inches. Unless otherwise specified, tolerances are 0.005 inch. 9. All diameters must be concentric to each other within 0.004 TIR. FIGURE 2. Contact, electrical, plug connector, ramp power, 416/240 volts, large, male. Provided by IHSNot for ResaleNo reproduction or ne
10、tworking permitted without license from IHS-,-,-MS27266B 4 Inches mm .002 .004 .005 .031 .216 .313 1.750 5.313 .051 .102 .127 .794 5.482 7.938 44.45 134.94 NOTES: 1. For use with MS27266-1. 2. Procurement specification MIL-DTL-38159. 3. Material: Brass, in accordance with ASTM-B36/B36M, ASTM-B121/B1
11、21M or ASTM-B124/B124M. See procurement specification. 4. Finish: See procurement specification. 5. Unless otherwise specified, machined surfaces 125 or better in accordance with ASME B46.1. 6. Remove all burrs and break all edges. 7. All dimensions shown are for finished part after plating. 8. Dime
12、nsions in inches. Unless otherwise specified, tolerances 0.005 inch. 9. All diameters must be concentric to each other within 0.004 TIR. FIGURE 3. Contact, electrical plug connector, ramp power, 416/240 volts, small, male. Provided by IHSNot for ResaleNo reproduction or networking permitted without
13、license from IHS-,-,-MS27266B 5 Dimensions and configurations: See figures 1, 2, and 3. Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Reference documents. In addition to MIL-DTL-3
14、8159, this document references the following. ASME B46.1 ASTM-B36/B36M ASTM-B121/B121M ASTM-B124/B124M CONCLUDING MATERIAL Custodians: Preparing activity: Air Force - 85 DLA - CC DLA - CC (Project 5935-2008-136) NOTE: The activities listed above were interested in this document as of date of this document. Since organization and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
