1、 DETAIL SPECIFICATION SHEET CONNECTORS, RECEPTACLE, ELECTRICAL, BOX, FLANGE MOUNT, SOLDER TYPE, BAYONET COUPLING, CLASS T, SERIES II This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall
2、consist of this specification sheet and MIL-DTL-27599. FIGURE 1. Receptacle, box, flange mount. AMSC N/A FSC 5935 INCH - POUNDMS27335E 31 August 2010 SUPERSEDING MS27335D 20 May 2005 Inactive for new design after 7 December 1998. Provided by IHSNot for ResaleNo reproduction or networking permitted w
3、ithout license from IHS-,-,-MS27335E 2 FIGURE 1. Receptacle, box, flange mount - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27335E 3 FIGURE 1. Receptacle, box, flange mount - Continued. Provided by IHSNot for ResaleNo reproduction o
4、r networking permitted without license from IHS-,-,-MS27335E 4 FIGURE 1. Receptacle, box, flange mount - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27335E 5 Inches mm Inches mm Inches mm Inches mm 0.001 0.0254 0.012 0.305 0.058 1.47
5、3 0.139 3.531 0.004 0.1016 0.015 0.381 0.063 1.600 0.188 4.775 0.005 0.127 0.02 0.508 0.078 1.981 0.223 5.664 0.010 0.254 0.039 0.991 0.116 2.947 0.239 6.071 0.011 0.279 0.053 1.346 0.126 3.200 0.322 8.179 NOTES: 1. Insert front surface shall be flat within .005 T.I.R. 2. Dimensions are in inches. M
6、etric equivalents are given for information only. 3. The point at which a gauge pin having the same basic diameter as the mating contact and a square face, touches socket contact spring. 4. Normal keyway position. For other keyway positions, see MIL-DTL-27599. 5. Diameters A and D shall be concentri
7、c within .015 T.I.R. 6. Diameter A with respect to diameter B, and diameter D with respect to diameter N, shall be concentric at MMC. 7. Diameters D and I shall be concentric within .005 T.I.R. at MMC. 8. The gauge features for GG shall be CC smaller than their MMC size at basic location. 9. The gau
8、ge features for GG shall be .010 smaller than their MMC size at basic location. FIGURE 1. Receptacle, box, flange mount - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27335E 6 TABLE I. Dimensions. 1/ 2/ Shell size A dia + .001 - .005
9、B dia + .000 - .016 over projections C dia + .006 - .002 D dia + .005 - .001 I dia .005 N dia + .005 - .006 8 .473 (12.01) .563 (14.30) .078 (1.98) .362 (9.19) .296 (7.52) .412 (10.46) 10 .590 (14.98) .680 (17.27) .490 (12.44) .413 (10.49) .540 (13.71) 12 .750 (19.05) .859 (21.82) .607 (15.42) .527
10、13.38) .689 (17.50) 14 .875 (22.22) .984 (25.00) .732 (18.59) .652 (16.56) .814 (20.67) 16 1.000 (25.40) 1.108 (28.14) .857 (21.77) .777 (19.73) .939 (23.85) 18 1.125 (28.57) 1.233 (31.32) .962 (24.43) .866 (22.00) 1.039 (26.39) 20 1.250 (31.75) 1.358 (34.49) .125 (3.175) 1.087 (27.60) .991 (25.17)
11、 1.164 (29.56) 22 1.375 (34.92) 1.483 (37.67) 1.212 (30.78) 1.116 (28.34) 1.289 (32.74) 24 1.500 (38.10) 1.610 (40.89) 1.337 33.96) 1.241 (31.52) 1.414 (35.91) See notes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27335E 7 TABL
12、E I. Dimensions Continued. 1/ 2/ Shell size Q max dia R BSC S max T + .010 - .005 V max dia CC 8 1.078 (27.38) .297 (7.54) .828 (21.03) .120 (3.05) .406 (10.31) .004 (.102) 10 1.266 (32.15) .3595 (9.1313) .954 (24.23) .516 (13.10) .010 (.254) 12 1.391 (35.33) .406 (10.31) 1.047 (26.59) .640 (16.26)
13、14 1.516 (38.50) .453 (11.50) 1.141 (28.98) .766 (19.45) 16 1.641 (41.68) .4845 (12.30) 1.234 (31.34) .890 (22.60) 18 1.766 (44.85) .531 (13.48) 1.328 (33.73) .984 (25.00) 20 1.891 (48.03) .578 (14.68) 1.453 (36.90) 1.109 (28.17) 22 2.016 (51.20) .625 (15.87) 1.578 (40.08) 1.234 (31.34) 24 2.204 (55
14、98) .6875 (17.46) 1.703 (43.25) .147 (3.73) 1.359 (34.52) 1/ Dimensions are in inches. 2/ Metric equivalents are given for information only. REQUIREMENTS: Dimensions and configurations: See figure 1 and table I. This connector mates with MS27336. Insert arrangement shall be in accordance with MIL-S
15、TD-1560. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27335E 8 Part or Identifying Number (PIN) example: MS27335 T 24 A 61 P A MS number Class Shell size Finish (color) Insert arrangement Style Polarizing position (No letter is required for norm
16、al position) Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents. In addition to MIL-DTL-27599, this document references the following: MIL-STD-1560 MS27336 CONCLUD
17、ING MATERIAL Custodians: Preparing activity: Air Force - 85 DLA - CC DLA - CC Review activities: Air Force - 99 (Project 5935-2010-101) DLA - IS NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
