1、 DETAIL SPECIFICATION SHEET CONNECTORS, RECEPTACLE, ELECTRICAL, JAM NUT MOUNTING, SOLDER TYPE, BAYONET COUPLING, CLASSES P AND T, SERIES II This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein
2、 shall consist of this specification sheet and MIL-DTL-27599. FIGURE 1. Receptacle, jam nut mounting. AMSC N/A FSC 5935 INCH - POUNDMS27337E 31 August 2010 SUPERSEDING MS27337D 20 May 2005 Inactive for new design after 7 December 1998. Provided by IHSNot for ResaleNo reproduction or networking permi
3、tted without license from IHS-,-,-MS27337E 2 FIGURE 1. Receptacle, jam nut mounting - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27337E 3 FIGURE 1. Receptacle, jam nut mounting - Continued. Provided by IHSNot for ResaleNo reproducti
4、on or networking permitted without license from IHS-,-,-MS27337E 4 Inches mm Inches mm Inches mm Inches mm 0.004 0.102 0.02 0.508 0.078 1.981 0.139 3.531 0.005 0.127 0.039 0.991 0.094 2.388 0.141 3.581 0.01 0.254 0.045 1.143 0.109 2.769 0.223 5.664 0.011 0.279 0.053 1.346 0.116 2.946 0.235 5.969 0.0
5、12 0.305 0.062 1.575 0.125 3.175 0.312 7.926 0.017 0.432 0.063 1.600 0.126 3.200 NOTES: 1. Dimensions are in inches. Metric equivalent are given for information only. 2. Insert front surface shall be flat within .005 T.I.R. 3. Diameters A, D, M, Q and Z shall be concentric within .015 T.I.R. 4. Diam
6、eters D and I shall be concentric within .005 T.I.R. at MMC. 5. Diameter A with respect to diameter B, and diameter D with respect to diameter N, shall be concentric at MMC. 6. Sides of groove may have 5 max taper. 7. Normal keyway position. For other keyway positions, see MIL-DTL-27599. 8. The poin
7、t at which a gauge pin having the same basic diameter as the mating contact and a square face, touches socket contact spring. 9. Recommended packing for o-ring shall be in accordance with SAE-AS3578. Recommended packing is for dimensions only. Material is optional. 10. The gauge features for GG shal
8、l be CC smaller than their MMC size at basic location. FIGURE 1. Receptacle, jam nut mounting - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27337E 5 TABLE I. Dimensions. 1/ 2/ Shell size A dia + .001 - .005 B dia + .000 - .016 over p
9、rojections C dia + .006 - .002 D dia + .005 - .001 F .005 H + .017 - .016 I dia .005 8 .473 (12.01) .563 (14.30) .078 (1.98) .362 (9.19) .438 (11.12) 1.062 (26.97) .296 (7.52) 10 .590 (14.98) .680 (17.27) .490 (12.44) 1.188 (30.17) .413 (10.49) 12 .750 (19.05) .859 (21.82) .607 (15.42) 1.312 (33.32)
10、 .527 (13.38) 14 .875 (22.22) .984 (25.00) .732 (18.59) 1.438 (36.52 .652 (16.56) 16 1.000 (25.40) 1.108 (28.14) .857 (21.77) 1.562 (39.67) .777 (19.73) 18 1.125 (28.57) 1.233 (31.32) .962 (24.43) 1.688 (42.87) .866 (22.00) 20 1.250 (31.75) 1.358 (34.49) .125 (3.175) 1.087 (27.60) .464 (11.78) 1.812
11、 (46.02) .991 (25.17) 22 1.375 (34.92) 1.483 (37.67) 1.212 (30.78) 2.000 (50.80) 1.116 (28.34) 24 1.500 (38.10) 1.610 (40.89) 1.337 33.96) 2.125 (53.97) 1.241 (31.52) See notes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27337E
12、 6 TABLE I. Dimensions - Continued. 1/ 2/ Shell size M Thread class 2A plated N dia + .005 - .006 N flat + .001 - .006 Q dia .016 S .016 8 7/8 - 20 UNEF .412 (10.46) .817 (20.75) 1.375 (34.92) 1.250 (31.75) 10 1 - 20 UNEF .540 (13.71) .941 (23.90) 1.500 (38.10) 1.375 (34.92) 12 1 1/8 - 18 UNEF .689
13、17.50) 1.065 (27.05) 1.625 (41.27) 1.500 (38.10) 14 1 1/4 - 18 UNEF .814 (20.67) 1.190 (30.23) 1.750 (44.45) 1.625 (41.27) 16 1 3/8 - 18 UNEF .939 (23.85) 1.320 (33.53) 1.938 (49.22) 1.750 (44.45) 18 1 1/2 - 18 UNEF 1.039 (26.39) 1.440 (36.57) 2.016 (51.20) 1.938 (49.22) 20 1 5/8 - 18 UNEF 1.164 (2
14、9.56) 1.565 (39.75) 2.141 (54.38) 2.016 (51.20) 22 1 3/4 - 18 UNS 1.289 (32.74) 1.690 (42.92) 2.265 (57.53) 2.141 (54.38) 24 1 7/8 - 16 UN 1.414 (35.91) 1.815 (46.10) 2.390 (60.70) 2.265 (57.53) See notes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without l
15、icense from IHS-,-,-MS27337E 7 TABLE I. Dimensions - Continued. 1/ 2/ Shell size Z dia + .006 - .005 CC DD min dia EE + .005 - .000 Recommended packing (O-ring) 8 .965 (24.51) .004 (.102) .678 (17.22) .140 (3.56) SAE-AS3578-022 10 1.090 (27.68) .010 (.254) .780 (19.81) SAE-AS3578-024 12 1.215 (30.86
16、) .963 (24.46) SAE-AS3578-026 14 1.340 (34.04) 1.088 (27.63) SAE-AS3578-028 16 1.477 (37.51) 1.222 (31.04) SAE-AS3578-029 18 1.602 (40.69) 1.333 (33.86) SAE-AS3578-030 20 1.727 (43.86) 1.458 (37.03) .166 (4.22) SAE-AS3578-031 22 1.852 (47.04) 1.583 (40.21) SAE-AS3578-032 24 1.977 (50.21) 1.708 (43.3
17、8) SAE-AS3578-033 1/ Dimensions are in inches. 2/ Metric equivalent are given for information only. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27337E 8 FIGURE 2. Receptacle, rear accessory areas. Provided by IHSNot for ResaleNo reproduction or
18、 networking permitted without license from IHS-,-,-MS27337E 9 TABLE II. Dimensions (rear accessory). 1/ 2/ Shell size LT max overall length VV thread UNEF-2A MOD (plated) LP max overall length XP min dia YP max dia size major dia MOD 8 .203 (5.16) .4375 - 28 .421 - .417 (10.69 10.60) .438 (11.12) .3
19、17 (8.05) .531 (13.48) 10 .5625 - 24 .542 - .538 (13.76 13.66) .434 (11.02) .641 (16.28) 12 .6875 - 24 .667 - .663 (16.94 16.84) .548 (13.92) .766 (19.45) 14 .8125 - 20 .791 - .787 (20.09 19.98) .673 (17.09) .891 (22.63) 16 .9375 - 20 .916 - .912 (23.26 23.16) .798 (20.27) 1.016 (25.80) 18 1.0625 -
20、18 1.034 - 1.030 (26.26 26.16) .899 (22.83) 1.125 (28.57) 20 .188 (4.77) 1.1875 - 18 1.158 - 1.154 (29.41 29.31) 1.024 (26.01) 1.250 (31.75) 22 1.3125 - 18 1.283 - 1.279 (32.58 32.48) 1.149 (29.18) 1.375 (34.92) 24 .250 (6.35) 1.4375 - 18 1.408 - 1.404 (35.76 35.66) 1.274 (32.36) 1.500 (38.10) 1/ Di
21、mensions are in inches. 2/ Metric equivalents are given for information only. REQUIREMENTS: Dimensions and configurations: See figures 1 and 2 and tables I and II. This connector mates with MS27336. Insert arrangement shall be in accordance with MIL-STD-1560. Provided by IHSNot for ResaleNo reproduc
22、tion or networking permitted without license from IHS-,-,-MS27337E 10 Part or Identifying Number (PIN) example: MS27337 T 12 A 98 P A MS number Class Shell size Finish (color) Insert arrangement Style Polarizing position (No letter is required for normal position) Changes from previous issue. Margin
23、al notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents. In addition to MIL-DTL-27599, this document references the following: MS27336 MIL-STD-1560 SAE-AS3578 Provided by IHSNot for ResaleNo reproduction
24、 or networking permitted without license from IHS-,-,-MS27337E 11 CONCLUDING MATERIAL Custodians: Preparing activity: Air Force - 85 DLA - CC DLA - CC Review activities: Air Force - 99 (Project 5935-2010-141) DLA - IS NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
